Abstract: The objective of this research is to mitigate and prevent
the alkali silica reactivity (ASR) in highway construction projects.
ASR is a deleterious reaction initiated when the silica content of the
aggregate reacts with alkali hydroxides in cement in the presence of
relatively high moisture content. The ASR results in the formation of
an expansive white colored gel-like material which forms the
destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the
State of Arkansas were mixed and mortar bars were poured according
to the ASTM specifications. Mortar bars expansion was measured
versus time and aggregates with potential ASR problems were
detected. Different types of supplementary cementitious materials
(SCMs) were used in remixing mortar bars with highly reactive
aggregates. Length changes for remixed bars proved that different
types of SCMs can be successfully used in reducing the expansive
effect of ASR. SCMs percentage by weight is highly dependent on
the SCM type. The result of this study will help avoiding future
losses due to ASR cracking in construction project and reduce the
maintenance, repair, and replacement budgets required for highways
network.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: This paper focuses on the study of DC-to-DC
converters, which are suitable for low-voltage high-power
applications. The output voltages generated by renewable energy
sources such as photovoltaic arrays and fuel cell stacks are
generally low and required to be increased to high voltage levels.
Development of DC-to-DC converters, which provide high step-up
voltage conversion ratios with high efficiencies and low voltage
stresses, is one of the main issues in the development of renewable
energy systems. A procedure for three converters−conventional
DC-to-DC converter, interleaved boost converter, and isolated flyback
based converter, is illustrated for a given set of specifications. The
selection among the converters for the given application is based on
the voltage conversion ratio, efficiency, and voltage stresses.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: Digital reference service is when a traditional library
reference service is provided electronically. In most cases users do
not get full satisfaction from using digital reference service due to
variety of reasons. This paper discusses the formal specification of
web services applications for digital reference services (WSDRS).
WSDRS is an informal model that claims to reduce the problems of
digital reference services in libraries. It uses web services technology
to provide efficient digital way of satisfying users’ need in the
reference section of libraries. Informal model is in natural language
which is inconsistent and ambiguous that may cause difficulties to the
developers of the system. In order to solve this problem we decided
to convert the informal specifications into formal specifications. This
is supposed to reduce the overall development time and cost. We use
Z language to develop the formal model and verify it with Z/EVES
theorem prover tool.
Abstract: The web services applications for digital reference
service (WSDRS) of LIS model is an informal model that claims to
reduce the problems of digital reference services in libraries. It uses
web services technology to provide efficient way of satisfying users’
needs in the reference section of libraries. The formal WSDRS model
consists of the Z specifications of all the informal specifications of
the model. This paper discusses the formal validation of the Z
specifications of WSDRS model. The authors formally verify and
thus validate the properties of the model using Z/EVES theorem
prover.
Abstract: The use of Flexible AC Transmission System
(FACTS) devices in a power system can potentially overcome
limitations of the present mechanically controlled transmission
system. Also, the advance of technology makes possible to include
new energy storage devices in the electrical power system. The
integration of Superconducting Magnetic Energy Storage (SMES)
into Static Synchronous Compensator (STATCOM) can lead to
increase their flexibility in improvement of power system dynamic
behaviour by exchanging both active and reactive powers with power
grids. This paper describes structure and behaviour of SMES,
specifications and performance principles of the STATCOM/SMES
compensator. Moreover, the benefits and effectiveness of integrated
SMES with STATCOM in power systems is presented. Also, the
performance of the STATCOM/SMES compensator is evaluated
using an IEEE 3-bus system through the dynamic simulation by
PSCAD/EMTDC software.
Abstract: This paper presents an approach for the classification of
an unstructured format description for identification of file formats.
The main contribution of this work is the employment of data mining
techniques to support file format selection with just the unstructured
text description that comprises the most important format features for
a particular organisation. Subsequently, the file format indentification
method employs file format classifier and associated configurations to
support digital preservation experts with an estimation of required file
format. Our goal is to make use of a format specification knowledge
base aggregated from a different Web sources in order to select file
format for a particular institution. Using the naive Bayes method,
the decision support system recommends to an expert, the file format
for his institution. The proposed methods facilitate the selection of
file format and the quality of a digital preservation process. The
presented approach is meant to facilitate decision making for the
preservation of digital content in libraries and archives using domain
expert knowledge and specifications of file formats. To facilitate
decision-making, the aggregated information about the file formats is
presented as a file format vocabulary that comprises most common
terms that are characteristic for all researched formats. The goal is to
suggest a particular file format based on this vocabulary for analysis
by an expert. The sample file format calculation and the calculation
results including probabilities are presented in the evaluation section.
Abstract: In order to address construction project requirements
and specifications, scholars and practitioners need to establish
taxonomy according to a scheme that best fits their need. While
existing characterization methods are continuously being improved,
new ones are devised to cover project properties which have not been
previously addressed. One such method, the Project Definition Rating
Index (PDRI), has received limited consideration strictly as a
classification scheme. Developed by the Construction Industry
Institute (CII) in 1996, the PDRI has been refined over the last two
decades as a method for evaluating a project's scope definition
completeness during front-end planning (FEP). The main
contribution of this study is a review of practical project classification
methods, and a discussion of how PDRI can be used to classify
projects based on their readiness in the FEP phase. The proposed
model has been applied to 59 construction projects in Ontario, and
the results are discussed.
Abstract: In this paper, a new concept of closed-loop design for a
product is presented. The closed-loop design model is developed by
integrating forward design and reverse design. Based on this new
concept, a closed-loop design model for sustainable manufacturing by
integrated evaluation of forward design, reverse design, and green
manufacturing using a fuzzy analytic network process is developed. In
the design stage of a product, with a given product requirement and
objective, there can be different ways to design the detailed
components and specifications. Therefore, there can be different
design cases to achieve the same product requirement and objective.
Subsequently, in the design evaluation stage, it is required to analyze
and evaluate the different design cases. The purpose of this research is
to develop a model for evaluating the design cases by integrated
evaluating the criteria in forward design, reverse design, and green
manufacturing. A fuzzy analytic network process method is presented
for integrated evaluation of the criteria in the three models. The
comparison matrices for evaluating the criteria in the three groups are
established. The total relational values among the three groups
represent the total relational effects. In applications, a super matrix
model is created and the total relational values can be used to evaluate
the design cases for decision-making to select the final design case. An
example product is demonstrated in this presentation. It shows that the
model is useful for integrated evaluation of forward design, reverse
design, and green manufacturing to achieve a closed-loop design for
sustainable manufacturing objective.
Abstract: The coaxial transformer-coupled push-pull circuitry
has been used widely in HF and VHF amplifiers for many decades
without significant changes in the topology of the transformers. Basic
changes over the years concerned the construction and turns ratio of
the transformers as has been imposed upon the newer technologies
active devices demands. The balun transmission line transformers
applied in push-pull amplifiers enable input/output impedance
transformation, but are mainly used to convert the balanced output
into unbalanced and the input unbalanced into balanced. A simple
and affordable alternative solution over the traditional coaxial
transformer is the coreless planar balun. A key advantage over the
traditional approach lies in the high specifications repeatability;
simplifying the amplifier construction requirements as the planar
balun constitutes an integrated part of the PCB copper layout. This
paper presents the performance analysis of a planar LDMOS
MRFE6VP5600 Push-Pull amplifier that enables robust operation in
Band III, DVB-T, DVB-T2 standards but functions equally well in
Band II, for DRM+ new generation transmitters.
Abstract: Moodle is an open source learning management
system that enables creation of a powerful and flexible learning
environment. Many organizations, especially learning institutions
have customized Moodle open source LMS for their own use. In
general open source LMSs are of great interest due to many
advantages they offer in terms of cost, usage and freedom to
customize to fit a particular context. Tanzania Secondary School e-
Learning (TanSSe-L) system is the learning management system for
Tanzania secondary schools. TanSSe-L system was developed using
a number of methods, one of them being customization of Moodle
Open Source LMS. This paper presents few areas on the way Moodle
OS LMS was customized to produce a functional TanSSe-L system
fitted to the requirements and specifications of Tanzania secondary
schools’ context.
Abstract: Experimental & numeral study of temperature
distribution during milling process, is important in milling quality
and tools life aspects. In the present study the milling cross-section
temperature is determined by using Artificial Neural Networks
(ANN) according to the temperature of certain points of the work
piece and the point specifications and the milling rotational speed of
the blade. In the present work, at first three-dimensional model of the
work piece is provided and then by using the Computational Heat
Transfer (CHT) simulations, temperature in different nods of the
work piece are specified in steady-state conditions. Results obtained
from CHT are used for training and testing the ANN approach. Using
reverse engineering and setting the desired x, y, z and the milling
rotational speed of the blade as input data to the network, the milling
surface temperature determined by neural network is presented as
output data. The desired points temperature for different milling
blade rotational speed are obtained experimentally and by
extrapolation method for the milling surface temperature is obtained
and a comparison is performed among the soft programming ANN,
CHT results and experimental data and it is observed that ANN soft
programming code can be used more efficiently to determine the
temperature in a milling process.
Abstract: Interaction between human, location and activity
defines space. In the framework of these relations, space is a
container for current specifications in relations of the 3 mentioned
elements. The change of land utility considered with average
performance range, urban regulations, society requirements etc. will
provide welfare and comfort for citizens. From an engineering view it
is fundamental that choosing a proper location for a specific civil
activity requires evaluation of locations from different perspectives.
The debate of desirable establishment of municipal service elements
in urban regions is one of the most important issues related to urban
planning. In this paper, the research type is applicable based on goal,
and is descriptive and analytical based on nature. Initially existing
terminals in Esfahan are surveyed and then new locations are
presented based on evaluated criteria. In order to evaluate terminals
based on the considered factors, an AHP model is used at first to
estimate weight of different factors and then existing and suggested
locations are evaluated using Arc GIS software and AHP model
results. The results show that existing bus terminals are located in
fairly proper locations. Further results of this study suggest new
locations to establish terminals based on urban criteria.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Several of the practical industrial control processes are
multivariable processes. Due to the relation amid the variables
(interaction), delay in the loops, it is very intricate to design a
controller directly for these processes. So first, the interaction of the
variables is analyzed using Relative Normalized Gain Array
(RNGA), which considers the time constant, static gain and delay
time of the processes. Based on the effect of RNGA, relative gain
array (RGA) and NI, the pair (control configuration) of variables to
be controlled by decentralized control is selected. The equivalent
transfer function (ETF) of the process model is estimated as first
order process with delay using the corresponding elements in the
Relative gain array and Relative average residence time array
(RARTA) of the processes. Secondly, a decentralized Proportional-
Integral (PI) controller is designed for each ETF simply using
frequency response specifications. Finally, the performance and
robustness of the algorithm is comparing with existing related
approaches to validate the effectiveness of the projected algorithm.
Abstract: Monocopter is a single-wing rotary flying vehicle
which has the capability of hovering. This flying vehicle includes two
dynamic parts in which more efficiency can be expected rather than
other Micro UAVs due to the extended area of wing compared to its
fuselage. Low cost and simple mechanism in comparison to other
vehicles such as helicopter are the most important specifications of
this flying vehicle.
In the previous paper we discussed the introduction of the final
system but in this paper, the experimental design process of
Monocopter and its control algorithm has been investigated in
general. Also the editorial bugs in the previous article have been
corrected and some translational ambiguities have been resolved.
Initially by constructing several prototypes and carrying out many
flight tests the main design parameters of this air vehicle were
obtained by experimental measurements. Eventually the required
main monocopter for this project was constructed. After construction
of the monocopter in order to design, implementation and testing of
control algorithms first a simple optic system used for determining
the heading angle. After doing numerous tests on Test Stand, the
control algorithm designed and timing of applying control inputs
adjusted. Then other control parameters of system were tuned in
flight tests. Eventually the final control system designed and
implemented using the AHRS sensor and the final operational tests
performed successfully.
Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.