Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: This paper discusses a qualitative simulator QRiOM
that uses Qualitative Reasoning (QR) technique, and a process-based
ontology to model, simulate and explain the behaviour of selected
organic reactions. Learning organic reactions requires the application
of domain knowledge at intuitive level, which is difficult to be
programmed using traditional approach. The main objective of
QRiOM is to help learners gain a better understanding of the
fundamental organic reaction concepts, and to improve their
conceptual comprehension on the subject by analyzing the multiple
forms of explanation generated by the software. This paper focuses
on the generation of explanation based on causal theories to explicate
various phenomena in the chemistry subject. QRiOM has been tested
with three classes problems related to organic chemistry, with
encouraging results. This paper also presents the results of
preliminary evaluation of QRiOM that reveal its explanation
capability and usefulness.
Abstract: Gas condensate Reservoirs show complicated thermodynamic behavior when their pressure reduces to under dew point pressure. Condensate blockage around the producing well cause significant reduction of production rate as well bottom-hole pressure drops below saturation pressure. The main objective of this work was to examine the well test analysis of naturally fractured lean gas condensate reservoir and investigate the effect of condensate formed around the well-bore on behavior of single phase pseudo pressure and its derivative curves. In this work a naturally fractured lean gas condensate reservoir is simulated with compositional simulator. Different sensitivity analysis done on Corry parameters and result of simulator is feed to analytical well testing software. For consideration of these phenomena eighteen compositional models with Capillary number effect are constructed. Matrix relative permeability obeys Corry relative permeability and relative permeability in fracture is linear. Well testing behavior of these models are studied and interpreted. Results show different sensitivity analysis on relative permeability of matrix does not have strong effect on well testing behavior even most part of the matrix around the well is occupied with condensate.
Abstract: Many metrics were proposed to evaluate the
characteristics of the analysis and design model of a given product
which in turn help to assess the quality of the product. Function point
metric is a measure of the 'functionality' delivery by the software.
This paper presents an analysis of a set of programs of a project
developed in Cµ through Function Points metric. Function points
are measured for a Data Flow Diagram (DFD) of the case developed
at initial stage. Lines of Codes (LOCs) and possible errors are
calculated with the help of measured Function Points (FPs). The
calculations are performed using suitable established functions.
Calculated LOCs and errors are compared with actual LOCs and
errors found at the time of analysis & design review, implementation
and testing. It has been observed that actual found errors are more
than calculated errors. On the basis of analysis and observations,
authors conclude that function point provides useful insight and helps
to analyze the drawbacks in the development process.
Abstract: Data mining incorporates a group of statistical
methods used to analyze a set of information, or a data set. It operates
with models and algorithms, which are powerful tools with the great
potential. They can help people to understand the patterns in certain
chunk of information so it is obvious that the data mining tools have
a wide area of applications. For example in the theoretical chemistry
data mining tools can be used to predict moleculeproperties or
improve computer-assisted drug design. Classification analysis is one
of the major data mining methodologies. The aim of thecontribution
is to create a classification model, which would be able to deal with a
huge data set with high accuracy. For this purpose logistic regression,
Bayesian logistic regression and random forest models were built
using R software. TheBayesian logistic regression in Latent GOLD
software was created as well. These classification methods belong to
supervised learning methods.
It was necessary to reduce data matrix dimension before construct
models and thus the factor analysis (FA) was used. Those models
were applied to predict the biological activity of molecules, potential
new drug candidates.
Abstract: Due to the environmental and price issues of current
energy crisis, scientists and technologists around the globe are
intensively searching for new environmentally less-impact form of
clean energy that will reduce the high dependency on fossil fuel.
Particularly hydrogen can be produced from biomass via thermochemical
processes including pyrolysis and gasification due to the
economic advantage and can be further enhanced through in-situ
carbon dioxide removal using calcium oxide. This work focuses on
the synthesis and development of the flowsheet for the enhanced
biomass gasification process in PETRONAS-s iCON process
simulation software. This hydrogen prediction model is conducted at
operating temperature between 600 to 1000oC at atmospheric
pressure. Effects of temperature, steam-to-biomass ratio and
adsorbent-to-biomass ratio were studied and 0.85 mol fraction of
hydrogen is predicted in the product gas. Comparisons of the results
are also made with experimental data from literature. The
preliminary economic potential of developed system is RM 12.57 x
106 which equivalent to USD 3.77 x 106 annually shows economic
viability of this process.
Abstract: Vision-based intelligent vehicle applications often require large amounts of memory to handle video streaming and image processing, which in turn increases complexity of hardware and software. This paper presents an FPGA implement of a vision-based blind spot warning system. Using video frames, the information of the blind spot area turns into one-dimensional information. Analysis of the estimated entropy of image allows the detection of an object in time. This idea has been implemented in the XtremeDSP video starter kit. The blind spot warning system uses only 13% of its logic resources and 95k bits block memory, and its frame rate is over 30 frames per sec (fps).
Abstract: Solutions for the temperature profile around a moving
heat source are obtained using both analytic and finite element
(FEM) methods. Analytic and FEM solutions are applied to study the
temperature profile in welding. A moving heat source is represented
using both point heat source and uniform distributed disc heat source
models. Analytic solutions are obtained by solving the partial
differential equation for energy conservation in a solid, and FEM
results are provided by simulating welding using the ANSYS
software. Comparison is made for quasi steady state conditions. The
results provided by the analytic solutions are in good agreement with
results obtained by FEM.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: Testing accounts for the major percentage of technical
contribution in the software development process. Typically, it
consumes more than 50 percent of the total cost of developing a
piece of software. The selection of software tests is a very important
activity within this process to ensure the software reliability
requirements are met. Generally tests are run to achieve maximum
coverage of the software code and very little attention is given to the
achieved reliability of the software. Using an existing methodology,
this paper describes how to use Bayesian Belief Networks (BBNs) to
select unit tests based on their contribution to the reliability of the
module under consideration. In particular the work examines how the
approach can enhance test-first development by assessing the quality
of test suites resulting from this development methodology and
providing insight into additional tests that can significantly reduce
the achieved reliability. In this way the method can produce an
optimal selection of inputs and the order in which the tests are
executed to maximize the software reliability. To illustrate this
approach, a belief network is constructed for a modern software
system incorporating the expert opinion, expressed through
probabilities of the relative quality of the elements of the software,
and the potential effectiveness of the software tests. The steps
involved in constructing the Bayesian Network are explained as is a
method to allow for the test suite resulting from test-driven
development.
Abstract: The primary cause of Total Hip Replacement (THR)
failure for younger patients is aseptic loosening. This complication is
twice more likely to happen in acetabular cup than in femoral stem.
Excessive micromotion between bone and implant will cause
loosening and it depends in patient activities, age and bone. In this
project, the effects of different metal back design of press fit on
osseointegration of the acetabular cup are carried out. Commercial
acetabular cup designs, namely Spiked, Superfix and Quadrafix are
modelled and analyzed using commercial finite element software.
The diameter of acetabular cup is based on the diameter of acetabular
rim to make sure the component fit to the acetabular cavity. A new
design of acetabular cup are proposed and analyzed to get better
osseointegration between the bones and implant interface. Results
shows that the proposed acetabular cup designs are more stable
compared to other designs with respect to stress and displacement
aspects.
Abstract: e-Government structures permits the government to operate in a more transparent and accountable manner of which it increases the power of the individual in relation to that of the government. This paper identifies the factors that determine customer-s attitude towards e-Government services using a theoretical model based on the Technology Acceptance Model. Data relating to the constructs were collected from 200 respondents. The research model was tested using Structural Equation Modeling (SEM) techniques via the Analysis of Moment Structure (AMOS 16) computer software. SEM is a comprehensive approach to testing hypotheses about relations among observed and latent variables. The proposed model fits the data well. The results demonstrated that e- Government services acceptance can be explained in terms of compatibility and attitude towards e-Government services. The setup of the e-Government services will be compatible with the way users work and are more likely to adopt e-Government services owing to their familiarity with the Internet for various official, personal, and recreational uses. In addition, managerial implications for government policy makers, government agencies, and system developers are also discussed.
Abstract: In this paper, we generalize several techniques in
developing Fault Tolerant Software. We introduce property
“Correctness" in evaluating N-version Systems and compare it to
some commonly used properties such as reliability or availability.
We also find out the relation between this property and the number of
versions of system. Our experiments to verify the correctness and the
applicability of the relation are also presented.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: An empirical study of web applications that use
software frameworks is presented here. The analysis is based on two
approaches. In the first, developers using such frameworks are
required, based on their experience, to assign weights to parameters
such as database connection. In the second approach, a performance
testing tool, OpenSTA, is used to compute start time and other such
measures. From such an analysis, it is concluded that open source
software is superior to proprietary software. The motivation behind
this research is to examine ways in which a quantitative assessment
can be made of software in general and frameworks in particular.
Concepts such as metrics and architectural styles are discussed along
with previously published research.
Abstract: This paper describes a system-level SoC energy
consumption estimation method based on a dynamic behavior of
embedded software in the early stages of the SoC development. A
major problem of SOC development is development rework caused by
unreliable energy consumption estimation at the early stages. The
energy consumption of an SoC used in embedded systems is strongly
affected by the dynamic behavior of the software. At the early stages
of SoC development, modeling with a high level of abstraction is
required for both the dynamic behavior of the software, and the
behavior of the SoC. We estimate the energy consumption by a UML
model-based simulation. The proposed method is applied for an actual
embedded system in an MFP. The energy consumption estimation of
the SoC is more accurate than conventional methods and this proposed
method is promising to reduce the chance of development rework in
the SoC development. ∈
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: Stuck-pipe in drilling operations is one of the most
pressing and expensive problems in the oil industry. This paper
describes a computational simulation and an experimental study of
the hydrodynamic vibrator, which may be used for liquidation of
stuck-pipe problems during well drilling. The work principle of the
vibrator is based upon the known phenomena of Vortex Street of
Karman and the resulting generation of vibrations. We will discuss
the computational simulation and experimental investigations of
vibrations in this device. The frequency of the vibration parameters
has been measured as a function of the wide range Reynolds Number.
The validity of the computational simulation and of the assumptions
on which it is based has been proved experimentally. The
computational simulation of the vibrator work and its effectiveness
was carried out using FLUENT software. The research showed high
degree of congruence with the results of the laboratory tests and
allowed to determine the effect of the granular material features upon
the pipe vibration in the well. This study demonstrates the potential
of using the hydrodynamic vibrator in a well drilling system.