Abstract: Along with increasing development of generation of supersonic planes especially fighters and request for increasing the performance and maneuverability scientists and engineers suggested the delta and double delta wing design. One of the areas which was necessary to be researched, was the Aerodynamic review of this type of wings in high angles of attack at low speeds that was very important in landing and takeoff the planes and maneuvers. Leading Edges of the wings,cause the separation flow from wing surface and then formation of powerful vortex with high rotational speed which studing the mechanism and location of formation and also the position of the vortex breakdown in high angles of attack is very important. In this research, a double delta wing with 76o/45o sweep angles at high angle of attack in steady state and incompressible flow were numerically analyzed with Fluent software. With analaysis of the numerical results, we arrived the most important characteristic of the double delta wings which is keeping of lift at high angles of attacks.
Abstract: Ti-6Al-4V alloy has demonstrated a high strength to
weight ratio as well as good properties at high temperature. The
successful application of the alloy in some important areas depends
on suitable joining techniques. Friction welding has many
advantageous features to be chosen for joining Titanium alloys. The
present work investigates the feasibility of producing similar metal
joints of this Titanium alloy by rotary friction welding method. The
joints are produced at three different speeds and the performances of
the welded joints are evaluated by conducting microstructure studies,
Vickers Hardness and tensile tests at the joints. It is found that the
weld joints produced are sound and the ductile fractures in the tensile
weld specimens occur at locations away from the welded joints. It is
also found that a rotational speed of 1500 RPM can produce a very
good weld, with other parameters kept constant.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: This paper quantifies the impact of providing a shortterm
excess active power support of a variable speed wind turbine
(VSWT) and effect of super magnetic energy storage (SMES) unit on
frequency control, particularly temporary minimum frequency (TMF)
term. To demonstrate the effect of these factors on the power system
frequency, a three-area power system is considered as a test system.
Abstract: The Navier Stokes Equations (NSE) for an incompressible fluid of variable viscosity in the presence of an unknown external force in Von-Mises system x,\ are transformed, and some new exact solutions for a class of flows characterized by equation y f x a\b for an arbitrary state equation are determined, where f x is a function, \ the stream function, a z 0 and b are the arbitrary constants. In three, out of four cases, the function f x is arbitrary, and the solutions are the solutions of the flow equations for all the flows characterized by the equationy f x a\b. Streamline patterns for some forms of f x in unbounded and bounded regions are given.
Abstract: Later marine propeller is the main component of ship
propulsion system. For a non-series propeller, it is difficult to
indicate the open water marine propeller performance without an
experimental study to measure the marine propeller parameters.
In the present study, the open water performance of a non-series
marine propeller has been carried out experimentally. The
geometrical aspects of a commercial non-series marine propeller
have been measured for a propeller blade area ratio of 0.3985. The
measured propeller performance parameters were the thrust and
torque coefficients for different propeller rotational speed and
different water channel flow velocity, then the open water
performance for the propeller has been plotted.
In addition, a direct comparison between the obtained
experimental results and a theoretical study of a B-series marine
propeller of the same blade area ratio has been carried out. A
correction factor has been introduced to apply the operating
conditions of the experimental results to that of the theoretical study
for the studied marine propeller.
Abstract: The primary objective of this paper was to construct a
“kinematic parameter-independent modeling of three-axis machine
tools for geometric error measurement" technique. Improving the
accuracy of the geometric error for three-axis machine tools is one of
the machine tools- core techniques. This paper first applied the
traditional method of HTM to deduce the geometric error model for
three-axis machine tools. This geometric error model was related to the
three-axis kinematic parameters where the overall errors was relative
to the machine reference coordinate system. Given that the
measurement of the linear axis in this model should be on the ideal
motion axis, there were practical difficulties. Through a measurement
method consolidating translational errors and rotational errors in the
geometric error model, we simplified the three-axis geometric error
model to a kinematic parameter-independent model. Finally, based on
the new measurement method corresponding to this error model, we
established a truly practical and more accurate error measuring
technique for three-axis machine tools.
Abstract: A brushless DC motor with integrated drive circuit for air management system is presented. Using magnetic equivalent circuit model a basic design of the motor is determined, and specific configurations are inspected thanks to finite element analysis. In order to reduce an unbalanced magnetic force in an axial direction, induced forces between a stator core and a permanent magnet are calculated with respect to the relative positions of them. For the high efficiency, and high power density, BLDC motor and drive are developed. Also vibration mode and eccentricity of a rotor are considered at the rated and maximum rotational speed Through the experimental results, a validity of the simulated one is confirmed.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: For many chemical and biological processes, the understanding of the mixing phenomenon and flow behavior in a stirred tank is of major importance. A three-dimensional numerical study was performed using the software Fluent, to study the flow field in a stirred tank with a Rushton turbine. In this work, we first studied the flow generated in the tank with a Rushton turbine. Then, we studied the effect of the variation of turbine’s submergence on the thermodynamic quantities defining the flow field. For that, four submergences were considered, while maintaining the same rotational speed (N =250rpm). This work intends to optimize the aeration performances of a Rushton turbine in a stirred tank.
Abstract: The Euler-s equation of motion is extended to include
the viscosity stress tensor leading to the formulation of Navier–
Stokes type equation. The latter is linearized and applied to
investigate the rotational motion or vorticity in a viscous fluid.
Relations for the velocity of viscous waves and attenuation parameter
are obtained in terms of viscosity (μ) and the density (¤ü) of the fluid.
μ and ¤ü are measured experimentally as a function of temperature for
two different samples of light and heavy crude oil. These data
facilitated to determine the activation energy, velocity of viscous
wave and the attenuation parameter. Shear wave velocity in heavy oil
is found to be much larger than the light oil, whereas the attenuation
parameter in heavy oil is quite low in comparison to light one. The
activation energy of heavy oil is three times larger than light oil.
Abstract: Dynamics of a vapour bubble generated due to a high local energy input near a circular thin bronze plate in the absence of the buoyancy forces is numerically investigated in this paper. The bubble is generated near a thin bronze plate and during the growth and collapse of the bubble, it deforms the nearby plate. The Boundary Integral Equation Method is employed for numerical simulation of the problem. The fluid is assumed to be incompressible, irrotational and inviscid and the surface tension on the bubble boundary is neglected. Therefore the fluid flow around the vapour bubble can be assumed as a potential flow. Furthermore, the thin bronze plate is assumed to have perfectly plastic behaviour. Results show that the displacement of the circular thin bronze plate has considerable effect on the dynamics of its nearby vapour bubble. It is found that by decreasing the thickness of the thin bronze plate, the growth and collapse rate of the bubble becomes higher and consequently the lifetime of the bubble becomes shorter.
Abstract: Magnetic Resonance Imaging play a vital role in the decision-diagnosis process of brain MR images. For an accurate diagnosis of brain related problems, the experts mostly compares both T1 and T2 weighted images as the information presented in these two images are complementary. In this paper, rotational and translational invariant form of Local binary Pattern (LBP) with additional gray scale information is used to retrieve similar slices of T1 weighted images from T2 weighted images or vice versa. The incorporation of additional gray scale information on LBP can extract more local texture information. The accuracy of retrieval can be improved by extracting moment features of LBP and reweighting the features based on users feedback. Here retrieval is done in a single subject scenario where similar images of a particular subject at a particular level are retrieved, and multiple subjects scenario where relevant images at a particular level across the subjects are retrieved.
Abstract: The changing economic climate has made global
manufacturing a growing reality over the last decade, forcing
companies from east and west and all over the world to
collaborate beyond geographic boundaries in the design,
manufacture and assemble of products. The ISO10303 and
ISO14649 Standards (STEP and STEP-NC) have been
developed to introduce interoperability into manufacturing
enterprises so as to meet the challenge of responding to
production on demand. This paper describes and illustrates a
STEP compliant CAD/CAPP/CAM System for the manufacture
of rotational parts on CNC turning centers. The information
models to support the proposed system together with the data
models defined in the ISO14649 standard used to create the NC
programs are also described. A structured view of a STEP
compliant CAD/CAPP/CAM system framework supporting the
next generation of intelligent CNC controllers for turn/mill
component manufacture is provided. Finally a proposed
computational environment for a STEP-NC compliant system
for turning operations (SCSTO) is described. SCSTO is the
experimental part of the research supported by the specification
of information models and constructed using a structured
methodology and object-oriented methods. SCSTO was
developed to generate a Part 21 file based on machining
features to support the interactive generation of process plans
utilizing feature extraction. A case study component has been
developed to prove the concept for using the milling and turning
parts of ISO14649 to provide a turn-mill CAD/CAPP/CAM
environment.
Abstract: This research was to study effect of rotational speed
and eccentric factors, which were affected on looseness of bearing.
The experiment was conducted on three rotational speeds and five
eccentric distances with 5 replications. The results showed that
influenced factor affected to looseness of bearing was rotational
speed and eccentric distance which showed statistical significant.
Higher rotational speed would cause on high looseness. Moreover,
more eccentric distance, more looseness of bearing. Using bearing at
high rotational with high eccentric of shaft would be affected
bearing fault more than lower rotational speed. The prediction
equation of looseness was generated by regression analysis. The
prediction has an effected to the looseness of bearing at 91.5%.
Abstract: This paper presents the application of a signal
intensity independent registration criterion for 2D rigid body
registration of medical images using 1D binary projections. The
criterion is defined as the weighted ratio of two projections. The ratio
is computed on a pixel per pixel basis and weighting is performed by
setting the ratios between one and zero pixels to a standard high
value. The mean squared value of the weighted ratio is computed
over the union of the one areas of the two projections and it is
minimized using the Chebyshev polynomial approximation using
n=5 points. The sum of x and y projections is used for translational
adjustment and a 45deg projection for rotational adjustment. 20 T1-
T2 registration experiments were performed and gave mean errors
1.19deg and 1.78 pixels. The method is suitable for contour/surface
matching. Further research is necessary to determine the robustness
of the method with regards to threshold, shape and missing data.
Abstract: The aim of the study was to evaluate the effect of
texturizers on the rheological properties of the apple mass and
desserts made from various raw materials. The apple varieties -
‘Antonovka’, ‘Baltais Dzidrais’, and ‘Zarja Alatau’ harvested in
Latvia, were used for the experiment. The apples were processed in a
blender unpeeled for obtaining a homogenous mass. The apple mass
was analyzed fresh and after storage at –18ºC. Both fresh and thawed
apple mass samples with added gelatin, xantan gum, and sodium
carboxymethylcellulose were whisked obtaining dessert. Pectin, pH
and soluble dry matter of the product were determined. Apparent
viscosity was measured using a rotational viscometer DV–III Ultra.
Pectin content in frozen apple mass decreased significantly (p
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: Rotational Smart Lighting Control System can supply
the quantity of lighting which is required to run plants by rotating few
LED and Fluorescent instead of that are used in the existing plant
factories.The initial installation of the existing plants factory is
expensive, so in order to solve the problem with smart lighting control
system was developed.
The beam required intensity for the growth of crops, Photosynthetic
Photon Flux Density(PPFD)is calculated; and the number of LED, are
installed on the blades, set; using the Lighting Simulation
Program.Relux, it is able to confirm that the difference of the beam
intensity between the center and the outer of lighting system when the
lighting device is rotating.