Abstract: Cold press technique is a traditional method to obtain oil. The cold-pressing procedure involves neither heat nor chemical treatments; therefore, cold press technique has low oil yield. The cold pressed herbal material residue still contains some oil after cold press. In this study, the oil that is remained in the cold pressed aniseed was extracted with hexane; and it was analyzed to determine physicochemical properties and quality parameters. It was found that the aniseed after cold press process still contained 10% oil. The values of other analysis parameters were 2.1 mgKOH/g for free fatty acid (FFA) and 7.6 meq02/kg for peroxide. Cold pressed aniseed oil values were determined as 2.1 mgKOH/g for FFA and 4.5 meq02/kg for peroxide, respectively. In addition, fatty acid composition was analyzed, and it was found that both types of oil had same fatty acid compositions. The main fatty acids were oleic, linoleic and palmitic acids.
Abstract: Society demands more reliable manufacturing processes
capable of producing high quality products in shorter production
cycles. New control algorithms have been studied to satisfy this
paradigm, in which Fault-Tolerant Control (FTC) plays a significant
role. It is suitable to detect, isolate and adapt a system when a harmful
or faulty situation appears. In this paper, a general overview about
FTC characteristics are exposed; highlighting the properties a system
must ensure to be considered faultless. In addition, a research to
identify which are the main FTC techniques and a classification
based on their characteristics is presented in two main groups:
Active Fault-Tolerant Controllers (AFTCs) and Passive Fault-Tolerant
Controllers (PFTCs). AFTC encompasses the techniques capable of
re-configuring the process control algorithm after the fault has been
detected, while PFTC comprehends the algorithms robust enough
to bypass the fault without further modifications. The mentioned
re-configuration requires two stages, one focused on detection,
isolation and identification of the fault source and the other one in
charge of re-designing the control algorithm by two approaches: fault
accommodation and control re-design. From the algorithms studied,
one has been selected and applied to a case study based on an
industrial hydraulic-press. The developed model has been embedded
under a real-time validation platform, which allows testing the FTC
algorithms and analyse how the system will respond when a fault
arises in similar conditions as a machine will have on factory. One
AFTC approach has been picked up as the methodology the system
will follow in the fault recovery process. In a first instance, the fault
will be detected, isolated and identified by means of a neural network.
In a second instance, the control algorithm will be re-configured to
overcome the fault and continue working without human interaction.
Abstract: As a way of managing the increasing volume and complexity of information that circulates in the present time, graphical representations are increasingly used, which add meaning to the information presented in communication media, through an efficient communication design. The visual culture itself, driven by technological evolution, has been redefining the forms of communication, so that contemporary visual communication represents a major impact on society. This article presents the results and respective comparative analysis of four publications in the Iberian press, focusing on the formal aspects of newspapers and the space they dedicate to the various communication elements. Two Portuguese newspapers and two Spanish newspapers were selected for this purpose. The findings indicated that the newspapers show a similarity in the use of graphic solutions, which corroborate a visual trend in communication design. The results also reveal that Spanish newspapers are more meticulous with graphic consistency. This study intended to contribute to improving knowledge of the Iberian generalist press.
Abstract: Since 1989, with the Fall of the Berlin Wall, Germany has undergone a profound restructuring political and economic process. When the Euro Crisis broke out, Germany was no longer the “sick man” of Europe. Instead, it had recovered its dominance as the strongest and wealthiest economy within the European Union. With the European Debt Crisis, that has been taking place in the European Union since the end of 2009, Germany´s Chancellor Angela Merkel has gained the power of deciding, so to say, on the fate of the debtor nations, but she neither stands for binding German commitments, nor refuses assistance. A debate on whether Merkel’s hesitation has been deliberated and used as a means of coercion has arisen on international print media, and the Portuguese Press has been no exception. This study, which was conducted by using news reporting, opinion articles, interviews and editorials, published in the Portuguese weekly Expresso and the daily Público, from 2008 to 2015, tries to show how Merkel’s hesitation, depicted in the press by the term “Merkiavelli”, was perceived in Portugal, a country that had to embrace the austerity measures, imposed by the European Central Bank, but defined under Angela Merkel´s leading role.
Abstract: This text focuses on the visual construction of youth in press photographs in socialist Czechoslovakia. It deals with photographs in a magazine for young readers, Mladý svět, published by the Socialist Union of Youth of Czechoslovakia. The aim of this study was to develop a methodological tool for uncovering the values and the ideological messages in the strategies used in the visual construction of reality in the socialist press. Two methods of visual analysis were applied to the photographs, a quantitative content analysis and a social semiotic analysis. The social semiotic analysis focused on images representing youth in their free time. The study shows that the meaning of a socialist press photograph is a result of a struggle for ideological power between formal and informal ideologies. This struggle takes place within the process of production of the photograph and also within the process of interpretation of the photograph.
Abstract: Military interventions have an important place in the Turkish Political History. Military interventions are commonly called coup in the society. By coup we mean that the armed forces seize political power either by a group of officer in the army or by chain of command. Coups not only weaken but also suspend the democracy in a country. All periods of coup created its own victims. Two military coups which took place in May 27, 1960 and September 12, 1980 are the most important ones in terms of political and social effect in the Turkish Political History. Apart these, March 12, 1971, February 28, 1997 and April 27, 2007 e-memorandum are the periods when Army submitted a memorandum and intervened the political government indirectly. Beside the memorandums and coups there were also many coup attempts that have been experienced in the Turkish Political History. In this study, we examined the coup attempted by FETO’s military members in the evening of July 15, 2016 from the point of the Turkish Press. Cumhuriyet, Haber Türk, Hürriyet, Milliyet, Sabah, Star, Yeni Akit and Yeni Şafak Newspapers which have different publication policies were examined within the scope of the study. The first pages of the newspapers dated July 16, 2016 were examined using content analysis method. The headlines, news, news headlines and the visual materials used for news were examined and the collected data were analysed.
Abstract: In the current study, fly ash obtained from a thermal power plant was used as reinforcement in pure magnesium. The composite materials with different fly ash contents were produced with powder metallurgical methods. Powder mixtures were sintered at 540oC under 30 MPa pressure for 15 minutes in a vacuum assisted hot press. Results showed that increasing ash content continuously increases hardness of the composite. On the other hand, minimum wear damage was obtained at 2 wt. % ash content. Addition of higher level of fly ash results with formation of cracks in the matrix and increases wear damage of the material.
Abstract: Shellac is a natural polyester resin secreted by insects. Pectins are natural, non-toxic and water-soluble polysaccharides extracted from the peels of citrus fruits or the leftovers of apples. Both polymers are allowed for the use in the pharmaceutical industry and as a food additive. SSB Aquagold® is the aqueous solution of shellac and can be used for a coating process as an enteric or controlled drug release polymer. In this study, tablets containing 10 mg methylene blue as a model drug were prepared with a rotary press. Those tablets were coated with mixtures of shellac and one of the pectin different types (i.e. CU 201, CU 501, CU 701 and CU 020) mostly in a 2:1 ratio or with pure shellac in a small scale fluidized bed apparatus. A stable, simple and reproducible three-stage coating process was successfully developed. The drug contents of the coated tablets were determined using UV-VIS spectrophotometer. The characterization of the surface and the film thickness were performed with the scanning electron microscopy (SEM) and the light microscopy. Release studies were performed in a dissolution apparatus with a basket. Most of the formulations were enteric coated. The dissolution profiles showed a delayed or sustained release with a lagtime of at least 4 h. Dissolution profiles of coated tablets with pure shellac had a very long lagtime ranging from 13 to 17.9 h and the slopes were quite high. The duration of the lagtime and the slope of the dissolution profiles could be adjusted by adding the proper type of pectin to the shellac formulation and by variation of the coating amount. In order to apply a coating formulation as a colon delivery system, the prepared film should be resistant against gastric fluid for at least 2 h and against intestinal fluid for 4-6 h. The required delay time was gained with most of the shellac-pectin polymer mixtures. The release profiles were fitted with the modified model of the Korsmeyer-Peppas equation and the Hixson-Crowell model. A correlation coefficient (R²)> 0.99 was obtained by Korsmeyer-Peppas equation.
Abstract: In the article, the wire winding process for the reinforcement of a pressure vessel frame has been studied. Firstly, the importance of the wire winding method has been explained. The main step in the design process is the methodology axial force control and wire winding process. The hot isostatic press and wire winding process introduce. With use the equilibrium term in the pressure vessel and frame, stresses in the frame wires analyzed. A case study frame was studied to control axial force in the hot isostatic press. Frame and them wires simulated then friction effect and wires effect in elastic yoke in the simulation model considered. Then theoretical and simulate resulted compare and vessel pressure import to frame because we assurance wire wounded not received to yielding point.
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: This research aims to study employment trends in
printing industry for prepress support by Suan Sunandha University
Fund. The objectives of this research are to explain the trends of the
employment in Thai Printing Industry for prepress in Bangkok and
the description of different personnel that prepress entrepreneur need
and also the problems of employment.
The population of prepress entrepreneurs is about 100
organizations in the area of Bangkok. The questionnaires has been
taken and analyzed with SPSS program by using the average
percentage and standard deviation.
This research is multiple case studies. The conceptual framework
is developed on the basis of the open systems theory.
The research result show that
1. The most of prepress entrepreneur have trend to choose the
employee by any sex, the age 25-29 years old, bachelor degree
and have 1-2 years experience.
2. The most problems are the understanding in job,
communication/relation and the understanding in new
technology.
3. The trends aims to employment in 1-3 years have 57.8% for
prepress industry in Bangkok.
This research suggests that:
1. Thai printing industry for prepress in Bangkok need quality
employee that expert in printing technology.
2. Prepress entrepreneur should have agreement to development
with university for practice the employee.
3. Prepress entrepreneur should support personal to fulfill the
knowledge.
Abstract: Recently, the advanced technologies that offer high
precision product, relative easy, economical process and also rapid
production are needed to realize the high demand of ultra precision
micro part. In our research, micromanufacturing based on soft
lithography and nanopowder injection molding was investigated. The
silicone metal pattern with ultra thick and high aspect ratio succeeds to
fabricate Polydimethylsiloxane (PDMS) micro mold. The process
followed by nanopowder injection molding (PIM) by a simple vacuum
hot press. The 17-4ph nanopowder with diameter of 100 nm, succeed
to be injected and it forms green sample microbearing with thickness,
microchannel and aspect ratio is 700μm, 60μm and 12, respectively.
Sintering process was done in 1200 C for 2 hours and heating rate
0.83oC/min. Since low powder load (45% PL) was applied to achieve
green sample fabrication, ~15% shrinkage happen in the 86% relative
density. Several improvements should be done to produce high
accuracy and full density sintered part.