Abstract: This article discusses stress analysis and the shape characteristics of the inflatable wing, and then introduces the design method of inflatable wing, in order to accurately approximate a standard airfoil. It specifically analyses the aerodynamic characteristics of the inflatable wing with the method of CFD, along with comparing to standard airfoil, afterwards we carries out the manufacture of inflatable wing and the flight test.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: In the present work we report a gram negative
bacterial isolate, from soil of a dye industry, with promising
biorefining and bioremediation potential. This isolate (GBS.5) could
utilize carbazole (nitrogen containing polycyclic aromatic
hydrocarbon) as the sole source of nitrogen and carbon and utilize
almost 98% of 3mM carbazole in 100 hours. The specific activity of
our GBS.5 isolate for carbazole degradation at 30°C and pH 7.0 was
found to be 11.36 μmol/min/g dry cell weight as compared to 10.4
μmol/min/g dry cell weight, the highest reported specific activity till
date. The presence of car genes (the genes involved in
denitrogenation of carbazole) was confirmed through PCR
amplification.
Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.