Abstract: The problem of conjugate free convection in a square
cavity filled with nanofluid and heated from below by spatial wall
temperature is studied numerically using the finite difference method.
Water-based nanofluid with copper nanoparticles are chosen for the
investigation. Governing equations are solved over a wide range
of nanoparticle volume fraction (0 ≤ φ ≤ 0.2), wave number
((0 ≤ λ ≤ 4) and thermal conductivity ratio (0.44 ≤ Kr ≤ 6). The
results presented for values of the governing parameters in terms of
streamlines, isotherms and average Nusselt number. It is found that
the flow behavior and the heat distribution are clearly enhanced with
the increment of the non-uniform heating.
Abstract: Due to the increasing growth of internet users, the emerging applications of multicast are growing day by day and there is a requisite for the design of high-speed switches/routers. Huge amounts of effort have been done into the research area of multicast switch fabric design and algorithms. Different traffic scenarios are the influencing factor which affect the throughput and delay of the switch. The pointer based multicast scheduling algorithms are not performed well under non-uniform traffic conditions. In this work, performance of the switch has been analyzed by applying the advanced multicast scheduling algorithm OQSMS (Optimal Queue Selection Based Multicast Scheduling Algorithm), MDDR (Multicast Due Date Round-Robin Scheduling Algorithm) and MDRR (Multicast Dual Round-Robin Scheduling Algorithm). The results show that OQSMS achieves better switching performance than other algorithms under the uniform, non-uniform and bursty traffic conditions and it estimates optimal queue in each time slot so that it achieves maximum possible throughput.
Abstract: Wetting efficiency of microstructures or nanostructures patterned on Si wafers is a real challenge in integrated circuits manufacturing. In fact, bad or non-uniform wetting during wet processes limits chemical reactions and can lead to non-complete etching or cleaning inside the patterns and device defectivity. This issue is more and more important with the transistors size shrinkage and concerns mainly high aspect ratio structures. Deep Trench Isolation (DTI) structures enabling pixels’ isolation in imaging devices are subject to this phenomenon. While low-frequency acoustic reflectometry principle is a well-known method for Non Destructive Test applications, we have recently shown that it is also well suited for nanostructures wetting characterization in a higher frequency range. In this paper, we present a high-frequency acoustic reflectometry characterization of DTI wetting through a confrontation of both experimental and modeling results. The acoustic method proposed is based on the evaluation of the reflection of a longitudinal acoustic wave generated by a 100 µm diameter ZnO piezoelectric transducer sputtered on the silicon wafer backside using MEMS technologies. The transducers have been fabricated to work at 5 GHz corresponding to a wavelength of 1.7 µm in silicon. The DTI studied structures, manufactured on the wafer frontside, are crossing trenches of 200 nm wide and 4 µm deep (aspect ratio of 20) etched into a Si wafer frontside. In that case, the acoustic signal reflection occurs at the bottom and at the top of the DTI enabling its characterization by monitoring the electrical reflection coefficient of the transducer. A Finite Difference Time Domain (FDTD) model has been developed to predict the behavior of the emitted wave. The model shows that the separation of the reflected echoes (top and bottom of the DTI) from different acoustic modes is possible at 5 Ghz. A good correspondence between experimental and theoretical signals is observed. The model enables the identification of the different acoustic modes. The evaluation of DTI wetting is then performed by focusing on the first reflected echo obtained through the reflection at Si bottom interface, where wetting efficiency is crucial. The reflection coefficient is measured with different water / ethanol mixtures (tunable surface tension) deposited on the wafer frontside. Two cases are studied: with and without PFTS hydrophobic treatment. In the untreated surface case, acoustic reflection coefficient values with water show that liquid imbibition is partial. In the treated surface case, the acoustic reflection is total with water (no liquid in DTI). The impalement of the liquid occurs for a specific surface tension but it is still partial for pure ethanol. DTI bottom shape and local pattern collapse of the trenches can explain these incomplete wetting phenomena. This high-frequency acoustic method sensitivity coupled with a FDTD propagative model thus enables the local determination of the wetting state of a liquid on real structures. Partial wetting states for non-hydrophobic surfaces or low surface tension liquids are then detectable with this method.
Abstract: Parallel Compressor Model (PCM) is a simplified approach to predict compressor performance with inlet distortions. In PCM calculation, it is assumed that the sub-compressors’ outlet static pressure is uniform and therefore simplifies PCM calculation procedure. However, if the compressor’s outlet duct is not long and straight, such assumption frequently induces error ranging from 10% to 15%. This paper provides a revised calculation method of PCM that can correct the error. The revised method employs energy equation, momentum equation and continuity equation to acquire needed parameters and replace the equal static pressure assumption. Based on the revised method, PCM is applied on two compression system with different blades types. The predictions of their performance in non-uniform inlet conditions are yielded through the revised calculation method and are employed to evaluate the method’s efficiency. Validating the results by experimental data, it is found that although little deviation occurs, calculated result agrees well with experiment data whose error ranges from 0.1% to 3%. Therefore, this proves the revised calculation method of PCM possesses great advantages in predicting the performance of the distorted compressor with limited exhaust duct.
Abstract: Compressor fans in modern aircraft engines are of considerate importance, as they provide majority of thrust required by the aircraft. Their challenging environment is frequently subjected to non-uniform inflow conditions. These conditions could be either due to the flight operating requirements such as take-off and landing, wake interference from aircraft fuselage or cross-flow wind conditions. So, in highly maneuverable flights regimes of fighter aircrafts affects the overall performance of an engine. Since the flow in compressor of an aircraft application is highly sensitive because of adverse pressure gradient due to different flow orientations of the aircraft. Therefore, it is prone to unstable operations. This paper presents the study that focuses on axial compressor response to inlet flow orientations for the range of angles as 0 to 15 degrees. For this purpose, NASA Rotor-37 was taken and CFD mesh was developed. The compressor characteristics map was generated for the design conditions of pressure ratio of 2.106 with the rotor operating at rotational velocity of 17188.7 rpm using CFD simulating environment of ANSYS-CFX®. The grid study was done to see the effects of mesh upon computational solution. Then, the mesh giving the best results, (when validated with the available experimental NASA’s results); was used for further distortion analysis. The flow in the inlet nozzle was given angle orientations ranging from 0 to 15 degrees. The CFD results are analyzed and discussed with respect to stall margin and flow separations due to induced distortions.
Abstract: This paper has focused on the most important parameters in the LSC uptake; inlet Re number and Sc number in the presence of non-uniform magnetic field. The magnetic field is arising from the thin wire with electric current placed vertically to the arterial blood vessel. According to the results of this study, applying magnetic field can be a treatment for atherosclerosis by reducing LSC along the vessel wall. Homogeneous porous layer as a arterial wall has been regarded. Blood flow has been considered laminar and incompressible containing Ferro fluid (blood and 4 % vol. Fe3O4) under steady state conditions. Numerical solution of governing equations was obtained by using the single-phase model and control volume technique for flow field.
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: This paper studies a mathematical model based on the
integral equations for dynamic analyzes numerical investigations of a
non-uniform or multi-material composite beam. The beam is
subjected to a sub-tangential follower force and elastic foundation.
The boundary conditions are represented by generalized
parameterized fixations by the linear and rotary springs. A
mathematical formula based on Euler-Bernoulli beam theory is
presented for beams with variable cross-sections. The non-uniform
section introduces non-uniformity in the rigidity and inertia of beams
and consequently, more complicated equilibrium who governs the
equation. Using the boundary element method and radial basis
functions, the equation of motion is reduced to an algebro-differential
system related to internal and boundary unknowns. A generalized
formula for the deflection, the slope, the moment and the shear force
are presented. The free vibration of non-uniform loaded beams is
formulated in a compact matrix form and all needed matrices are
explicitly given. The dynamic stability analysis of slender beam is
illustrated numerically based on the coalescence criterion. A realistic
case related to an industrial chimney is investigated.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: The elastic properties and fracture of two-dimensional
graphene were calculated purely from the atomic bonding (stretching
and bending) based on molecular mechanics method. Considering the
representative unit cell of graphene under various loading conditions,
the deformations of carbon bonds and the variations of the interlayer
distance could be realized numerically under the geometry constraints
and minimum energy assumption. In elastic region, it was found that
graphene was in-plane isotropic. Meanwhile, the in-plane deformation
of the representative unit cell is not uniform along armchair direction
due to the discrete and non-uniform distributions of the atoms. The
fracture of graphene could be predicted using fracture criteria based on
the critical bond length, over which the bond would break. It was
noticed that the fracture behavior were directional dependent, which
was consistent with molecular dynamics simulation results.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: Water flow management is one of the most important
parts of river engineering. Non-uniformity distribution of rainfall and
various flow demand with unreasonable flow management will be
caused destroyed of river ecosystem. Then, it is very serious to
determine ecosystem flow requirement. In this paper, Flow duration
curve indices method which has hydrological based was used to
evaluate environmental flow in Gharasou River, Ardabil, Iran. Using
flow duration curve, Q90 and Q95 for different return periods were
calculated. Their magnitude were determined as 1-day, 3-day, 7-day
and 30 day. According the second method, hydraulic alteration
indices often had low and medium range. In order to maintain river at
an acceptable ecological condition, minimum daily discharge of
index Q95 is 0.7 m3.s-1.
Abstract: Due to water shortage, application of saline water for
irrigation is an urgent in agriculture. In this study the effect of
calcium and potassium application as additive in saline root media for
reduce salinity adverse effects was investigated on tomato growth in
a hydroponic system with unequal distribution of salts in the root
media, which was divided in to two equal parts containing full
Johnson nutrient solution and 40 mMNaCl solution, alone or in
combination with KCl (6 mM), CaCl2 (4 mM), K+Ca (3+2 mM) or
half-strength Johnson nutrient solution. The root splits were
exchanged every 7 days. Results showed that addition of calcium,
calcium-potassium and nutrition elements equivalent to half the
concentration of Johnson formula to the saline-half of culture media
minimized the reduction in plant growth caused by NaCl, although
addition of potassium to culture media wasn’t effective. The greatest
concentration of sodium was observed at the shoot of treatments
which had smallest growth. According to the results of this study, in
case of dynamic and non-uniform distribution of salts in the root
media, by addition of additive to the saline solution, it would be
possible to use of saline water with no significant growth reduction.
Abstract: Tumor is an uncontrolled growth of tissues in any part
of the body. Tumors are of different types and they have different
characteristics and treatments. Brain tumor is inherently serious and
life-threatening because of its character in the limited space of the
intracranial cavity (space formed inside the skull). Locating the tumor
within MR (magnetic resonance) image of brain is integral part of the
treatment of brain tumor. This segmentation task requires
classification of each voxel as either tumor or non-tumor, based on
the description of the voxel under consideration. Many studies are
going on in the medical field using Markov Random Fields (MRF) in
segmentation of MR images. Even though the segmentation process
is better, computing the probability and estimation of parameters is
difficult. In order to overcome the aforementioned issues, Conditional
Random Field (CRF) is used in this paper for segmentation, along
with the modified artificial bee colony optimization and modified
fuzzy possibility c-means (MFPCM) algorithm. This work is mainly
focused to reduce the computational complexities, which are found in
existing methods and aimed at getting higher accuracy. The
efficiency of this work is evaluated using the parameters such as
region non-uniformity, correlation and computation time. The
experimental results are compared with the existing methods such as
MRF with improved Genetic Algorithm (GA) and MRF-Artificial
Bee Colony (MRF-ABC) algorithm.
Abstract: This study models the use of transcutaneous electrical
nerve stimulation on skin with a disk electrode in order to simulate
tissue damage. The current density distribution above a disk electrode
is known to be a dynamic and non-uniform quantity that is intensified
at the edges of the disk. The non-uniformity is subject to change
through using various electrode geometries or stimulation methods.
One of these methods known as edge-retarded stimulation has shown
to reduce this edge enhancement. Though progress has been made in
modeling the behavior of a disk electrode, little has been done to test
the validity of these models in simulating the actual heat transfer
from the electrode. This simulation uses finite element software to
couple the injection of current from a disk electrode to heat transfer
described by the Pennesbioheat transfer equation. An example
application of this model is studying an experimental form of
stimulation, known as edge-retarded stimulation. The edge-retarded
stimulation method will reduce the current density at the edges of the
electrode. It is hypothesized that reducing the current density edge
enhancement effect will, in turn, reduce temperature change and
tissue damage at the edges of these electrodes. This study tests this
hypothesis as a demonstration of the capabilities of this model. The
edge-retarded stimulation proved to be safer after this simulation. It is
shown that temperature change and the fraction of tissue necrosis is
much greater in the square wave stimulation. These results bring
implications for changes of procedures in transcutaneous electrical
nerve stimulation and transcutaneous spinal cord stimulation as well.
Abstract: Photoacoustic imaging (PAI) is a non-invasive and
non-ionizing imaging modality that combines the absorption contrast
of light with ultrasound resolution. Laser is used to deposit optical
energy into a target (i.e., optical fluence). Consequently, the target
temperature rises, and then thermal expansion occurs that leads to
generating a PA signal. In general, most image reconstruction
algorithms for PAI assume uniform fluence within an imaging object.
However, it is known that optical fluence distribution within the
object is non-uniform. This could affect the reconstruction of PA
images. In this study, we have investigated the influence of optical
fluence distribution on PA back-propagation imaging using finite
element method. The uniform fluence was simulated as a triangular
waveform within the object of interest. The non-uniform fluence
distribution was estimated by solving light propagation within a
tissue model via Monte Carlo method. The results show that the PA
signal in the case of non-uniform fluence is wider than the uniform
case by 23%. The frequency spectrum of the PA signal due to the
non-uniform fluence has missed some high frequency components in
comparison to the uniform case. Consequently, the reconstructed
image with the non-uniform fluence exhibits a strong smoothing
effect.
Abstract: In this paper we introduce a bacteria-leukocyte model
with bacteria chemotaxsis. We assume that bacteria develop a tactic
defence mechanism as a response to Leukocyte phagocytosis. We
explore the effect of this tactic motion on Turing space in two
parameter spaces. A fine tuning of bacterial chemotaxis shows a
significant effect on developing a non-uniform steady state.
Abstract: A study to estimate the size of the cabin and major
aircraft components as well as detect and avoid interference between
internally placed components and the external surface, during the
conceptual design synthesis and optimisation to explore the design
space of a BWB, was conducted. Sizing of components follows the
Bradley cabin sizing and rubber engine scaling procedures to size
the cabin and engine respectively. The interference detection and
avoidance algorithm relies on the ability of the Class Shape Transform
parameterisation technique to generate polynomial functions of the
surfaces of a BWB aircraft configuration from the sizes of the
cabin and internal objects using few variables. Interference detection
is essential in packaging of non-conventional configuration like
the BWB because of the non-uniform airfoil-shaped sections and
resultant varying internal space. The unique configuration increases
the need for a methodology to prevent objects from being placed in
locations that do not sufficiently enclose them within the geometry.
Abstract: This paper describes a new efficient blind source separation method; in this method we uses a non-uniform filter bank and a new structure with different sub-bands. This method provides a reduced permutation and increased convergence speed comparing to the full-band algorithm. Recently, some structures have been suggested to deal with two problems: reducing permutation and increasing the speed of convergence of the adaptive algorithm for correlated input signals. The permutation problem is avoided with the use of adaptive filters of orders less than the full-band adaptive filter, which operate at a sampling rate lower than the sampling rate of the input signal. The decomposed signals by analysis bank filter are less correlated in each sub-band than the input signal at full-band, and can promote better rates of convergence.