Abstract: In the present study, the effect of Si, Al, Ti, Zr, and Nb addition on the microstructure and hot workability of cast M42 tool steels, basically consisting of 1.0C, 0.2Mn, 3.8Cr, 1.5W, 8.5Co, 9.2Mo, and 1.0V in weight percent has been investigated. Tool steels containing Si of 0.25 and 0.5wt.%, Al of 0.06 and 0.12wt.%, Ti of 0.3wt.%, Zr of 0.3wt.%, and Nb of 0.3wt.% were cast into ingots of 140mm ´ 140mm ´ 330mm by vacuum induction melting. After solution treatment at 1150oC for 1.5hr followed by furnace cooling, hot rolling at 1180oC was conducted on the ingots. Addition of titanium, zirconium and niobium was found to retard the decomposition of the eutectic carbides and result in the deterioration of hot workability of the tool steels, while addition of aluminum and silicon showed relatively well decomposed carbide structure and resulted in sound hot rolled plates.
Abstract: This paper proposes a novel e-learning model that is
based on a dynamic formative evaluation. On evaluating the existing
format of e-learning, conditions regarding repetitive learning to
achieve mastery, causes issues for learners to lose tension and become
neglectful of learning. The dynamic formative evaluation proposed is
able to supplement limitation of the existing approaches. Since a
repetitive learning method does not provide a perfect feedback, this
paper puts an emphasis on the dynamic formative evaluation that is
able to maximize learning achievement. Through the dynamic
formative evaluation, the instructor is able to refer to the evaluation
result when making an estimation about the learner. To show the flow
chart of learning, based on the dynamic formative evaluation, the
model proves its effectiveness and validity.
Abstract: Al/Cu clad sheet has been fabricated by using differential speed rolling (DSR) process, which caused severe shear deformation between Al and Cu plate to easily bond to each other. Rolling was carried out at 100 and 150oC with speed ratios from 1.4 to 2.2, in which the total thickness reduction was in the range between 14 and 46%. Interfacial microstructure and mechanical properties of Al/Cu clad were investigated by scanning electron microscope equipped with energy dispersive X-ray detector, and tension tests. The DSR process was very effective to provide a good interface for atoms diffusion during subsequent annealing. The strength of bonding was higher with the increasing speed ratio. Post heat treatment enhanced the mechanical properties of clad sheet by forming intermetallic compounds in the interface area.
Abstract: As the ecology of Lake Shihwa has been restored significantly nowadays, the urban development is in progress around Lake Shihwa areas. Each development project includes a plan on utilizing waterfront areas, but there exist a difference on waterfront design criteria between experts and users. Therefore, it is significant to analyze preferences in design elements of existing waterfront parks around Lake Shihwa (Ansan Waterfront Park, Shihwa Reed Wetland Park, and T-Light Park) based on users’ perspectives and to reflect the result on upcoming waterfront developments. This study derives design elements on waterfront parks from literature reviews. The survey questionnaires are created based on these classified elements and the surveys are conducted to experts and users with in-depth interviews. For all three parks, several park facilities appear to be not recognized by users. Therefore the circulation path should be introduced in guide maps and information activities and furthermore in disposition of park facilities.
Abstract: In this paper, the development of the ephemeris generation module used for the Thaichote satellite operations is presented. It is a vital part of the flight dynamics system, which comprises, the orbit determination, orbit propagation, event prediction and station-keeping maneouvre modules. In the generation of the spacecraft ephemeris data, the estimated orbital state vector from the orbit determination module is used as an initial condition. The equations of motion are then integrated forward in time to predict the satellite states. The higher geopotential harmonics, as well as other disturbing forces, are taken into account to resemble the environment in low-earth orbit. Using a highly accurate numerical integrator based on the Burlish-Stoer algorithm the ephemeris data can be generated for long-term predictions, by using a relatively small computation burden and short calculation time. Some events occurring during the prediction course that are related to the mission operations, such as the satellite’s rise/set viewed from the ground station, Earth and Moon eclipses, the drift in groundtrack as well as the drift in the local solar time of the orbital plane are all detected and reported. When combined with other modules to form a flight dynamics system, this application is aimed to be applied for the Thaichote satellite and successive Thailand’s Earth-observation missions.
Abstract: This paper is about middleware which enables group-user applications on mobile devices in physical proximity to interact with other devices without intervention of a central server. Requirements of the middleware are identified from service usage scenarios, and the functional architecture of the middleware is specified. These requirements include Group Management, Synchronization, and Resource Management. Group Management needs to provide various capabilities to such applications with respect to managing multiple users (e.g., creation of groups, discovery of group or individual users, member join/leave, election of a group manager and service-group association) using D2D communication technology. We designed the middleware for the above requirements on the Android platform.
Abstract: CFRP (Carbon Fiber Reinforced Polymer) is mainly used as reinforcing material for degraded structures owing to its advantages including its non-corrodibility, high strength and lightweight properties. Recently, dedicated studies focused not only on its simple bonding but also on its tensioning. The tension necessary for prestressing requires the anchoring of multi-CFRP tendons with high capacity and the surface treatment of the CFRP tendons may also constitute an important issue according to the type of anchor. The wedge type, swage type or bonded type anchor can be used to anchor the CFRP tendon. The bonded type anchor presents the disadvantage to lengthen the length of the anchor due to the low bond strength of the CFRP tendon without surface treatment. This study intends to overcome this drawback through the application of a method enlarging the bond area at the end of the CFRP tendon. This method enlarges the bond area by splitting the end of the CFRP tendon along its length and can be applied when CFRP is produced by pultrusion. The application of this method shows that the mono-CFRP tendon and 3-multi CFRP tendon secured the anchor performance corresponding to the tensile performance of the CFRP tendon and that the 7-multi tendon secured anchor performance corresponding to 90% of the tensile strength due to the occurrence of buckling in the steel tube anchorage.
Abstract: Existence of plastic equation of state has been investigated by performing a series of load relaxation tests at various temperatures using an Al-Li alloy. A plastic equation of state is first developed from a simple kinetics consideration for a mechanical activation process of a leading dislocation piled up against grain boundaries. A series of load relaxation test has been conducted at temperatures ranging from 200 to 530oC to obtain the stress-strain rate curves. A plastic equation of state has been derived from a simple consideration of dislocation kinetics and confirmed by experimental results.
Abstract: Automated intelligent, clinical decision support systems generally promote to help or to assist physicians and patients regarding to prevention of diseases or treatment of illnesses using computer represented knowledge and information. In this paper, assessment factors affecting the proper design of clinical decision support system were investigated. The required procedure steps for gathering the data from clinical trial and extracting the information from large volume of healthcare repositories were listed, which are necessary for validation and verification of evidence-based implementation of clinical decision support system. The goal of this paper is to extract useful evaluation factors affecting the quality of the clinical decision support system in the design, development, and implementation of a computer-based decision support system.
Abstract: This paper aims to quantify the impact of natural disaster on tourism by the change of annual visitors to scenic spots. The data of visitors to Alishan, Sun Moon Lake, Sitou and Palace Museum in Taiwan during 1986 to 2012 year is collected, and the trend analysis is used to predict the annual visitors to these scenic spots. The findings show that 1999 Taiwan earthquake had significant effect on the visitors to Alishan, Sun Moon Lake and Sitou with an average impact of 55.75% during 1999 to 2000 year except for Palace Museum. The impact was greater as closer epicenter of 1999 earthquake. And the discovery period of visitors is about 2 to 9 years. Further, the impact of heavy rainfall on Alishan, Taiwan is estimated. As the accumulative rainfall reaches to 500 mm, the impact on visitors can be predicted.
Abstract: This paper presents a car parking monitoring system using wireless sensor networks. Multiple sensor nodes and a sink node, a gateway, and a server constitute a wireless network for monitoring a parking lot. Each of the sensor nodes is equipped with a 3-axis AMR sensor and deployed in the center of a parking space. Each sensor node reads its sensor values periodically and transmits the data to the sink node if the current and immediate past sensor values show a difference exceeding a threshold value. The sensor nodes and sink node use the 448 MHz band for wireless communication. Since RF transmission only occurs when sensor values show abrupt changes, the number of RF transmission operations is reduced and battery power can be conserved. The data from the sensor nodes reach the server via the sink node and gateway. The server determines which parking spaces are taken by cars based upon the received sensor data and reference values. The reference values are average sensor values measured by each sensor node when the corresponding parking spot is not occupied by a vehicle. Because the decision making is done by the server, the computational burden of the sensor node is relieved, which helps reduce the duty cycle of the sensor node.
Abstract: Textures of AZ31 Mg alloy sheets were evaluated by using neutron diffraction method in this study. The AZ31 sheets were fabricated either by conventional casting and subsequent hot rolling or strip casting. The effect of warm rolling was investigated using the AZ31 Mg alloy sheet produced by conventional casting. Warm rolling of 30% thickness reduction per pass was possible without any side-crack at temperatures as low as 200oC under the roll speed of 30 m/min. The initial microstructure of conventionally cast specimen was found to be partially recrystallized structures. Grain refinement was found to occur actively during the warm rolling. The (0002),(10-10) (10-11),and (10-12) complete pole figures were measured using the HANARO FCD (Neutron Four Circle Diffractometer) and ODF were calculated. The major texture of all specimens can be expressed by ND//(0001) fiber texture. Texture of hot rolled specimen showed the strongest fiber component, while that of strip cast sheet seemed to be similar to random distribution.
Abstract: This paper describes fast and efficient method for page segmentation of document containing nonrectangular block. The segmentation is based on edge following algorithm using small window of 16 by 32 pixels. This segmentation is very fast since only border pixels of paragraph are used without scanning the whole page. Still, the segmentation may contain error if the space between them is smaller than the window used in edge following. Consequently, this paper reduce this error by first identify the missed segmentation point using direction information in edge following then, using X-Y cut at the missed segmentation point to separate the connected columns. The advantage of the proposed method is the fast identification of missed segmentation point. This methodology is faster with fewer overheads than other algorithms that need to access much more pixel of a document.
Abstract: Identification of cancer genes that might anticipate
the clinical behaviors from different types of cancer disease is
challenging due to the huge number of genes and small number of
patients samples. The new method is being proposed based on
supervised learning of classification like support vector machines
(SVMs).A new solution is described by the introduction of the
Maximized Margin (MM) in the subset criterion, which permits to
get near the least generalization error rate. In class prediction
problem, gene selection is essential to improve the accuracy and to
identify genes for cancer disease. The performance of the new
method was evaluated with real-world data experiment. It can give
the better accuracy for classification.
Abstract: In this paper, we validate crater detection in moon surface image using FLDA. This proposal assumes that it is applied to SLIM (Smart Lander for Investigating Moon) project aiming at the pin-point landing to the moon surface. The point where the lander should land is judged by the position relations of the craters obtained via camera, so the real-time image processing becomes important element. Besides, in the SLIM project, 400kg-class lander is assumed, therefore, high-performance computers for image processing cannot be equipped. We are studying various crater detection methods such as Haar-Like features, LBP, and PCA. And we think these methods are appropriate to the project, however, to identify the unlearned images obtained by actual is insufficient. In this paper, we examine the crater detection using FLDA, and compare with the conventional methods.
Abstract: Most of researches for conventional simulations were
studied focusing on flocks with a single species. While there exist the
flocking behaviors with a single species in nature, the flocking
behaviors are frequently observed with multi-species. This paper
studies on the flocking simulation for heterogeneous agents. In order
to simulate the flocks for heterogeneous agents, the conventional
method uses the identifier of flock, while the proposed method defines
the feature vector of agent and uses the similarity between agents by
comparing with those feature vectors. Based on the similarity, the
paper proposed the attractive force and repulsive force and then
executed the simulation by applying two forces. The results of
simulation showed that flock formation with heterogeneous agents is
very natural in both cases. In addition, it showed that unlike the
existing method, the proposed method can not only control the density
of the flocks, but also be possible for two different groups of agents to
flock close to each other if they have a high similarity.
Abstract: This research was to study on background and social
and cultural context of Kamchanoad community for sustainable
tourism management. All data was collected through in-depth
interview with village headmen, community committees, teacher,
monks, Kamchanoad forest field officers and respected senior citizen
above 60 years old in the community who have lived there for more
than 40 years. Altogether there were 30 participants for this research.
After analyzing the data, content from interview and discussion,
Kamchanoad has both high land and low land in the region as well as
swamps that are very capable of freshwater animals’ conservation.
Kamchanoad is also good for agriculture and animal farming. 80% of
Kamchanoad’s land are forest, freshwater and rice farms.
Kamchanoad was officially set up as community in 1994 as “Baan
Nonmuang”. Inhabitants in Kamchanoad make a living by farming
based on sufficiency economy. They have rice farm, eucalyptus farm,
cassava farm and rubber tree farm. Local people in Kamchanoad still
believe in the myth of Srisutto Naga. They are still religious and love
to preserve their traditional way of life. In order to understand how to
create successful tourism business in Kamchanoad, we have to study
closely on local culture and traditions. Outstanding event in
Kamchanoad is the worship of Grand Srisutto, which is on the fullmoon
day of 6th month or Visakhabucha Day. Other big events are
also celebration at the end of Buddhist lent, Naga firework, New
Year celebration, Boon Mahachart, Songkran, Buddhist Lent, Boon
Katin and Loy Kratong. Buddhism is the main religion in
Kamchanoad. The promotion of tourism in Kamchanoad is expected
to help spreading more income for this region. More infrastructures
will be provided for local people as well as funding for youth support
and people activities.
Abstract: People detection from images has a variety of applications such as video surveillance and driver assistance system, but is still a challenging task and more difficult in crowded environments such as shopping malls in which occlusion of lower parts of human body often occurs. Lack of the full-body information requires more effective features than common features such as HOG. In this paper, new features are introduced that exploits global self-symmetry (GSS) characteristic in head-shoulder patterns. The features encode the similarity or difference of color histograms and oriented gradient histograms between two vertically symmetric blocks. The domain-specific features are rapid to compute from the integral images in Viola-Jones cascade-of-rejecters framework. The proposed features are evaluated with our own head-shoulder dataset that, in part, consists of a well-known INRIA pedestrian dataset. Experimental results show that the GSS features are effective in reduction of false alarmsmarginally and the gradient GSS features are preferred more often than the color GSS ones in the feature selection.
Abstract: This paper presents an automated inspection algorithm
for a thick plate. Thick plates typically have various types of surface
defects, such as scabs, scratches, and roller marks. These defects have
individual characteristics including brightness and shape. Therefore, it
is not simple to detect all the defects. In order to solve these problems
and to detect defects more effectively, we propose a dual light
switching lighting method and a defect detection algorithm based on
Gabor filters.
Abstract: This work was conducted to improve the level of
resistant starch (RS) in a rice noodle using unripe banana flour and to
investigate the effect of substitution of unripe banana flour for rice
flour on the physical properties of rice noodle. In order to prepare
rice noodles, the unripe banana flour were replaced the rice flour
with different degrees of substitutions including 0, 20, 40, 60, 80, and
100%. The results indicated that substitution of unripe banana flour
was significantly affected the viscosity properties of noodle flour,
color, cooking loss, RS and total starch content of noodle. It was
found that the noodle prepared from 100% unripe banana indicated
the greatest changes on the viscosity properties and color profiles. It
also showed the highest values of cooking loss (2.53%), tensile
strength (129.03%), and RS content (13.15%).