Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Supply chain consists of all stages involved, directly
or indirectly, includes all functions involved in fulfilling a customer
demand. In two stage transportation supply chain problem,
transportation costs are of a significant proportion of final product
costs. It is often crucial for successful decisions making approaches
in two stage supply chain to explicit account for non-linear
transportation costs. In this paper, deterministic demand and finite
supply of products was considered. The optimized distribution level
and the routing structure from the manufacturing plants to the
distribution centres and to the end customers is determined using
developed mathematical model and solved by proposed particle
swarm optimization based genetic algorithm. Numerical analysis of
the case study is carried out to validate the model.
Abstract: This article presents a detailed analysis and comparative
performance evaluation of model reference adaptive control systems.
In contrast to classical control theory, adaptive control methods allow
to deal with time-variant processes. Inspired by the works [1] and
[2], two methods based on the MIT rule and Lyapunov rule are
applied to a linear first order system. The system is simulated and
it is investigated how changes to the adaptation gain affect the
system performance. Furthermore, variations in the reference model
parameters, that is changing the desired closed-loop behaviour are
examinded.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: This paper proposes a method for speckle reduction in
medical ultrasound imaging while preserving the edges with the
added advantages of adaptive noise filtering and speed. A nonlinear
image diffusion method that incorporates local image parameter,
namely, scatterer density in addition to gradient, to weight the
nonlinear diffusion process, is proposed. The method was tested for
the isotropic case with a contrast detail phantom and varieties of
clinical ultrasound images, and then compared to linear and some
other diffusion enhancement methods. Different diffusion parameters
were tested and tuned to best reduce speckle noise and preserve
edges. The method showed superior performance measured both
quantitatively and qualitatively when incorporating scatterer density
into the diffusivity function. The proposed filter can be used as a
preprocessing step for ultrasound image enhancement before
applying automatic segmentation, automatic volumetric calculations,
or 3D ultrasound volume rendering.
Abstract: Diffuse viral encephalitis may lack fever and other cardinal signs of infection and hence its distinction from other acute encephalopathic illnesses is challenging. Often, the EEG changes seen routinely are nonspecific and reflect diffuse encephalopathic changes only. The aim of this study was to use nonlinear dynamic mathematical techniques for analyzing the EEG data in order to look for any characteristic diagnostic patterns in diffuse forms of encephalitis.It was diagnosed on clinical, imaging and cerebrospinal fluid criteria in three young male patients. Metabolic and toxic encephalopathies were ruled out through appropriate investigations. Digital EEGs were done on the 3rd to 5th day of onset. The digital EEGs of 5 male and 5 female age and sex matched healthy volunteers served as controls.Two sample t-test indicated that there was no statistically significant difference between the average values in amplitude between the two groups. However, the standard deviation (or variance) of the EEG signals at FP1-F7 and FP2-F8 are significantly higher for the patients than the normal subjects. The regularisation dimension is significantly less for the patients (average between 1.24-1.43) when compared to the normal persons (average between 1.41-1.63) for the EEG signals from all locations except for the Fz-Cz signal. Similarly the wavelet dimension is significantly less (P = 0.05*) for the patients (1.122) when compared to the normal person (1.458). EEGs are subdued in the case of the patients with presence of uniform patterns, manifested in the values of regularisation and wavelet dimensions, when compared to the normal person, indicating a decrease in chaotic nature.
Abstract: Daily production of information and importance of the sequence of produced data in forecasting future performance of market causes analysis of data behavior to become a problem of analyzing time series. But time series that are very complicated, usually are random and as a result their changes considered being unpredictable. While these series might be products of a deterministic dynamical and nonlinear process (chaotic) and as a result be predictable. Point of Chaotic theory view, complicated systems have only chaotically face and as a result they seem to be unregulated and random, but it is possible that they abide by a specified math formula. In this article, with regard to test of strange attractor and biggest Lyapunov exponent probability of chaos on several foreign exchange rates vs. IRR (Iranian Rial) has been investigated. Results show that data in this market have complex chaotic behavior with big degree of freedom.
Abstract: In this paper, the C1-conforming finite element method is analyzed for a class of nonlinear fourth-order hyperbolic partial differential equation. Some a priori bounds are derived using Lyapunov functional, and existence, uniqueness and regularity for the weak solutions are proved. Optimal error estimates are derived for both semidiscrete and fully discrete schemes.
Abstract: This paper describes a complex energy signal model
that is isomorphic with digital human fingerprint images. By using
signal models, the problem of fingerprint matching is transformed
into the signal processing problem of finding a correlation between
two complex signals that differ by phase-rotation and time-scaling. A
technique for minutiae matching that is independent of image
translation, rotation and linear-scaling, and is resistant to missing
minutiae is proposed. The method was tested using random data
points. The results show that for matching prints the scaling and
rotation angles are closely estimated and a stronger match will have a
higher correlation.
Abstract: This paper presents the design of a ring-shaped tri-axial fore sensor that can be incorporated into the tip of a guidewire for use in minimally invasive surgery (MIS). The designed sensor comprises a ring-shaped structure located at the center of four cantilever beams. The ringdesign allows surgical tools to be easily passed through which largely simplified the integration process. Silicon nanowires (SiNWs) are used aspiezoresistive sensing elementsembeddedon the four cantilevers of the sensor to detect the resistance change caused by the applied load.An integration scheme with new designed guidewire tip structure having two coils at the distal end is presented. Finite element modeling has been employed in the sensor design to find the maximum stress location in order to put the SiNWs at the high stress regions to obtain maximum output. A maximum applicable force of 5 mN is found from modeling. The interaction mechanism between the designed sensor and a steel wire has been modeled by FEM. A linear relationship between the applied load on the steel wire and the induced stress on the SiNWs were observed.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: This research investigates the effects of the opening
shape and location on the structural behavior of reinforced concrete
deep beam with openings, while keeping the opening size unchanged.
The software ANSYS 12.1 is used to handle the nonlinear finite
element analysis. The ultimate strength of reinforced concrete deep
beam with opening obtained by ANSYS 12.1 shows fair agreement
with the experimental results, with a difference of no more than 20%. The present work concludes that the opening location has much more effect on the structural strength than the opening shape. It was
concluded that placing the openings near the upper corners of the
deep beam may double the strength, and the use of a rectangular
narrow opening, with the long sides in the horizontal direction, can save up to 40% of structural strength of the deep beam.
Abstract: This paper presents a simple and sensitive kinetic
spectrophotometric method for the determination of ramipril in
commercial dosage forms. The method is based on the reaction of the
drug with 1-chloro-2,4-dinitrobenzene (CDNB) in dimethylsulfoxide
(DMSO) at 100 ± 1ºC. The reaction is followed
spectrophotometrically by measuring the rate of change of the
absorbance at 420 nm. Fixed-time (ΔA) and equilibrium methods are
adopted for constructing the calibration curves. Both the calibration
curves were found to be linear over the concentration ranges 20 - 220
μg/ml. The regression analysis of calibration data yielded the linear
equations: Δ A = 6.30 × 10-4 + 1.54 × 10-3 C and A = 3.62 × 10-4 +
6.35 × 10-3 C for fixed time (Δ A) and equilibrium methods,
respectively. The limits of detection (LOD) for fixed time and
equilibrium methods are 1.47 and 1.05 μg/ml, respectively. The
method has been successfully applied to the determination of ramipril
in commercial dosage forms. Statistical comparison of the results
shows that there is no significant difference between the proposed
methods and Abdellatef-s spectrophotometric method.
Abstract: A multivariable discontinuous feedback linearization approach is proposed to position control of an electrically driven fast robot manipulator. A desired performance is achieved by selecting a useful controller and suitable sampling rate and considering saturation for actuators. There is a high flexibility to apply the proposed control approach on different electrically driven manipulators. The control approach can guarantee the stability and satisfactory tracking performance. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a desired performance for control system under technical specifications.
Abstract: The increasing competitiveness in manufacturing
industry is forcing manufacturers to seek effective processing
schedules. The paper presents an optimization manufacture
scheduling approach for dependent details processing with given
processing sequences and times on multiple machines. By defining
decision variables as start and end moments of details processing it is
possible to use straightforward variables restrictions to satisfy
different technological requirements and to formulate easy to
understand and solve optimization tasks for multiple numbers of
details and machines. A case study example is solved for seven base
moldings for CNC metalworking machines processed on five
different machines with given processing order among details and
machines and known processing time-s duration. As a result of linear
optimization task solution the optimal manufacturing schedule
minimizing the overall processing time is obtained. The
manufacturing schedule defines the moments of moldings delivery
thus minimizing storage costs and provides mounting due-time
satisfaction. The proposed optimization approach is based on real
manufacturing plant problem. Different processing schedules variants
for different technological restrictions were defined and implemented
in the practice of Bulgarian company RAIS Ltd. The proposed
approach could be generalized for other job shop scheduling
problems for different applications.
Abstract: As global industry developed rapidly, the energy
demand also rises simultaneously. In the production process, there’s a
lot of energy consumed in the process. Formally, the energy used in
generating the heat in the production process. In the total energy
consumption, 40% of the heat was used in process heat, mechanical
work, chemical energy and electricity. The remaining 50% were
released into the environment. It will cause energy waste and
environment pollution. There are many ways for recovering the waste
heat in factory. Organic Rankine Cycle (ORC) system can produce
electricity and reduce energy costs by recovering the waste of low
temperature heat in the factory. In addition, ORC is the technology
with the highest power generating efficiency in low-temperature heat
recycling. However, most of factories executives are still hesitated
because of the high implementation cost of the ORC system, even a lot
of heat are wasted. Therefore, this study constructs a nonlinear
mathematical model of waste heat recovery equipment configuration
to maximize profits. A particle swarm optimization algorithm is
developed to generate the optimal facility installation plan for the ORC
system.
Abstract: This present paper proposes the modified Elastic Strip
method for mobile robot to avoid obstacles with a real time system in
an uncertain environment. The method deals with the problem of
robot in driving from an initial position to a target position based on
elastic force and potential field force. To avoid the obstacles, the
robot has to modify the trajectory based on signal received from the
sensor system in the sampling times. It was evident that with the
combination of Modification Elastic strip and Pseudomedian filter to
process the nonlinear data from sensor uncertainties in the data
received from the sensor system can be reduced. The simulations and
experiments of these methods were carried out.