Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: Rice husk is one of the alternative fuels for Thailand because of its high potential and environmental benefits. Nonetheless, the environmental profile of the electricity production from rice husk must be assessed to ensure reduced environmental damage. A 10 MW pilot plant using rice husk as feedstock is the study site. The environmental impacts from rice husk power plant are evaluated by using the Life Cycle Assessment (LCA) methodology. Energy, material and carbon balances have been determined for tracing the system flow. Carbon closure has been used for describing of the net amount of CO2 released from the system in relation to the amount being recycled between the power plant and the CO2 adsorbed by rice husk. The transportation of rice husk to the power plant has significant on global warming, but not on acidification and photo-oxidant formation. The results showed that the impact potentials from rice husk power plant are lesser than the conventional plants for most of the categories considered; except the photo-oxidant formation potential from CO. The high CO from rice husk power plant may be due to low boiler efficiency and high moisture content in rice husk. The performance of the study site can be enhanced by improving the combustion efficiency.
Abstract: This paper presents a new sensor-based online method for generating collision-free near-optimal paths for mobile robots pursuing a moving target amidst dynamic and static obstacles. At each iteration, first the set of all collision-free directions are calculated using velocity vectors of the robot relative to each obstacle and target, forming the Directive Circle (DC), which is a novel concept. Then, a direction close to the shortest path to the target is selected from feasible directions in DC. The DC prevents the robot from being trapped in deadlocks or local minima. It is assumed that the target's velocity is known, while the speeds of dynamic obstacles, as well as the locations of static obstacles, are to be calculated online. Extensive simulations and experimental results demonstrated the efficiency of the proposed method and its success in coping with complex environments and obstacles.
Abstract: We present a new intuitionistic fuzzy aggregation
operator called the intuitionistic fuzzy ordered weighted
averaging-weighted average (IFOWAWA) operator. The main
advantage of the IFOWAWA operator is that it unifies the OWA
operator with the WA in the same formulation considering the degree
of importance that each concept has in the aggregation. Moreover, it is
able to deal with an uncertain environment that can be assessed with
intuitionistic fuzzy numbers. We study some of its main properties and
we see that it has a lot of particular cases such as the intuitionistic
fuzzy weighted average (IFWA) and the intuitionistic fuzzy OWA
(IFOWA) operator. Finally, we study the applicability of the new
approach on a financial decision making problem concerning the
selection of financial strategies.
Abstract: Following the loss of NASA's Space Shuttle
Columbia in 2003, it was determined that problems in the agency's
organization created an environment that led to the accident. One
component of the proposed solution resulted in the formation of the
NASA Engineering Network (NEN), a suite of information retrieval
and knowledge-sharing tools. This paper describes the
implementation of communities of practice, which are formed along
engineering disciplines. Communities of practice enable engineers to
leverage their knowledge and best practices to collaborate and take
information learning back to their jobs and embed it into the
procedures of the agency. This case study offers insight into using
traditional engineering disciplines for virtual collaboration, including
lessons learned during the creation and establishment of NASA-s
communities.
Abstract: Current image-based individual human recognition
methods, such as fingerprints, face, or iris biometric modalities
generally require a cooperative subject, views from certain aspects,
and physical contact or close proximity. These methods cannot
reliably recognize non-cooperating individuals at a distance in the
real world under changing environmental conditions. Gait, which
concerns recognizing individuals by the way they walk, is a relatively
new biometric without these disadvantages. The inherent gait
characteristic of an individual makes it irreplaceable and useful in
visual surveillance.
In this paper, an efficient gait recognition system for human
identification by extracting two features namely width vector of
the binary silhouette and the MPEG-7-based region-based shape
descriptors is proposed. In the proposed method, foreground objects
i.e., human and other moving objects are extracted by estimating
background information by a Gaussian Mixture Model (GMM) and
subsequently, median filtering operation is performed for removing
noises in the background subtracted image. A moving target classification
algorithm is used to separate human being (i.e., pedestrian)
from other foreground objects (viz., vehicles). Shape and boundary
information is used in the moving target classification algorithm.
Subsequently, width vector of the outer contour of binary silhouette
and the MPEG-7 Angular Radial Transform coefficients are taken as
the feature vector. Next, the Principal Component Analysis (PCA)
is applied to the selected feature vector to reduce its dimensionality.
These extracted feature vectors are used to train an Hidden Markov
Model (HMM) for identification of some individuals. The proposed
system is evaluated using some gait sequences and the experimental
results show the efficacy of the proposed algorithm.
Abstract: This study demonstrates the use of Class F fly ash in
combination with lime or lime kiln dust in the full depth reclamation
(FDR) of asphalt pavements. FDR, in the context of this paper, is a
process of pulverizing a predetermined amount of flexible pavement
that is structurally deficient, blending it with chemical additives and
water, and compacting it in place to construct a new stabilized base
course. Test sections of two structurally deficient asphalt pavements
were reclaimed using Class F fly ash in combination with lime and
lime kiln dust. In addition, control sections were constructed using
cement, cement and emulsion, lime kiln dust and emulsion, and mill
and fill. The service performance and structural behavior of the FDR
pavement test sections were monitored to determine how the fly ash
sections compared to other more traditional pavement rehabilitation
techniques. Service performance and structural behavior were
determined with the use of sensors embedded in the road and Falling
Weight Deflectometer (FWD) tests. Monitoring results of the FWD
tests conducted up to 2 years after reclamation show that the cement,
fly ash+LKD, and fly ash+lime sections exhibited two year resilient
modulus values comparable to open graded cement stabilized
aggregates (more than 750 ksi). The cement treatment resulted in a
significant increase in resilient modulus within 3 weeks of
construction and beyond this curing time, the stiffness increase was
slow. On the other hand, the fly ash+LKD and fly ash+lime test
sections indicated slower shorter-term increase in stiffness. The fly
ash+LKD and fly ash+lime section average resilient modulus values
at two years after construction were in excess of 800 ksi. Additional
longer-term testing data will be available from ongoing pavement
performance and environmental condition data collection at the two
pavement sites.
Abstract: The number of framework conceived for e-learning
constantly increase, unfortunately the creators of learning materials
and educational institutions engaged in e-formation adopt a
“proprietor" approach, where the developed products (courses,
activities, exercises, etc.) can be exploited only in the framework
where they were conceived, their uses in the other learning
environments requires a greedy adaptation in terms of time and
effort. Each one proposes courses whose organization, contents,
modes of interaction and presentations are unique for all learners,
unfortunately the latter are heterogeneous and are not interested by
the same information, but only by services or documents adapted to
their needs. Currently the new tendency for the framework
conceived for e-learning, is the interoperability of learning materials,
several standards exist (DCMI (Dublin Core Metadata Initiative)[2],
LOM (Learning Objects Meta data)[1], SCORM (Shareable Content
Object Reference Model)[6][7][8], ARIADNE (Alliance of Remote
Instructional Authoring and Distribution Networks for Europe)[9],
CANCORE (Canadian Core Learning Resource Metadata
Application Profiles)[3]), they converge all to the idea of learning
objects. They are also interested in the adaptation of the learning
materials according to the learners- profile. This article proposes an
approach for the composition of courses adapted to the various
profiles (knowledge, preferences, objectives) of learners, based on
two ontologies (domain to teach and educational) and the learning
objects.
Abstract: A new chelating resin is prepared by coupling Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer. The resulting sorbent has been characterized by FT-IR, elemental analysis and thermogravimetric analysis (TGA) and studied for preconcentrating of Fe (II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the iron ions was 6.5. The resin was subjected to evaluation through batch binding of mentioned metal ion. Quantitative desorption occurs instantaneously with 0.5 M HNO3. The sorption capacity was found 4.1 mmol.g-1 of resin for Fe (II) in the aqueous solution. The chelating resin can be reused for 10 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 97% was obtained the metal ions with 0.5 M HNO3 as eluting agent. The method was applied for metal ions determination from industrial waste water sample.
Abstract: Nanostructured Iron Oxide with different
morphologies of rod-like and granular have been suc-cessfully
prepared via a solid-state reaction in the presence of NaCl, NaBr, NaI
and NaN3, respectively. The added salts not only prevent a drastic
increase in the size of the products but also provide suitable
conditions for the oriented growth of primary nanoparticles. The
formation mechanisms of these materials by solid-state reaction at
ambient temperature are proposed. The photocatalytic experiments
for congo red (CR) have demonstrated that the mixture of α-Fe2O3
and Fe3O4 nanostructures were more efficient than α-Fe2O3
nanostructures.
Abstract: The purpose of this study is i) to investigate the driving factors and barriers of the adoption of Information and Communication Technology (ICT) in Halal logistic and ii) to develop an ICT adoption framework for Halal logistic service provider. The Halal LSPs selected for the study currently used ICT service platforms, such as accounting and management system for Halal logistic business. The study categorizes the factors influencing the adoption decision and process by LSPs into four groups: technology related factors, organizational and environmental factors, Halal assurance related factors, and government related factors. The major contribution in this study is the discovery that technology related factors (ICT compatibility with Halal requirement) and Halal assurance related factors are the most crucial factors among the Halal LSPs applying ICT for Halal control in transportation-s operation. Among the government related factors, ICT requirement for monitoring Halal included in Halal Logistic Standard on Transportation (MS2400:2010) are the most influencing factors in the adoption of ICT with the support of the government. In addition, the government related factors are very important in the reducing the main barriers and the creation of the atmosphere of ICT adoption in Halal LSP sector.
Abstract: Environmental factors affect agriculture production
productivity and efficiency resulted in changing of profit efficiency.
This paper attempts to estimate the impacts of environmental factors
to profitability of rice farmers in the Red River Delta of Vietnam. The
dataset was extracted from 349 rice farmers using personal
interviews. Both OLS and MLE trans-log profit functions were used
in this study. Five production inputs and four environmental factors
were included in these functions. The estimation of the stochastic
profit frontier with a two-stage approach was used to measure
profitability. The results showed that the profit efficiency was about
75% on the average and environmental factors change profit
efficiency significantly beside farm specific characteristics. Plant
disease, soil fertility, irrigation apply and water pollution were the
four environmental factors cause profit loss in rice production. The
result indicated that farmers should reduce household size, farm
plots, apply row seeding technique and improve environmental
factors to obtain high profit efficiency with special consideration is
given for irrigation water quality improvement.
Abstract: Today we tend to go back to the past to our root
relation to nature. Therefore in search of friendly spaces there are
elements of natural environment introduced as elements of spatial
composition. Though reinvented through the use of the new
substance such as greenery, water etc. made possible by state of the
art technologies, still, in principal, they remain the same. As a result,
sustainable design, based upon the recognized means of composition
in addition to the relation of architecture and urbanism vs. nature
introduces a new aesthetical values into architectural and urban
space.
Abstract: In this research, an aerobic composting method is
studied to reuse organic waste from rubber factory waste as soil fertilizer and to study the effect of cellulolytic microbial activator
(CMA) as the activator in the rubber factory waste composting. The
performance of the composting process was monitored as a function
of carbon and organic matter decomposition rate, temperature and
moisture content. The results indicate that the rubber factory waste is best composted with water hyacinth and sludge than composted
alone. In addition, the CMA is more affective when mixed with the rubber factory waste, water hyacinth and sludge since a good fertilizer is achieved. When adding CMA into the rubber factory
waste composted alone, the finished product does not achieve a
standard of fertilizer, especially the C/N ratio.
Finally, the finished products of composting rubber factory waste and water hyacinth and sludge (both CMA and without CMA), can be an environmental friendly alternative to solve the disposal problems of rubber factory waste. Since the C/N ratio, pH, moisture
content, temperature, and nutrients of the finished products are acceptable for agriculture use.
Abstract: In this paper an effective approach for segmenting
human skin regions in images taken at different environment is
proposed. The proposed method uses a color distance map that is
flexible enough to reliably detect the skin regions even if the
illumination conditions of the image vary. Local image conditions is
also focused, which help the technique to adaptively detect differently
illuminated skin regions of an image. Moreover, usage of local
information also helps the skin detection process to get rid of picking
up much noisy pixels.
Abstract: Business transformation initiatives are required by
any organization to jump from its normal mode of operation to the
one that is suitable for the change in the environment such as
competitive pressures, regulatory requirements, changes in labor
market, etc., or internal such as changes in strategy/vision, changes in
the capability, change in the management, etc. Recent advances in
information technology in automating the business processes have
the potential to transform an organization to provide it with a
sustained competitive advantage. Process constitutes the skeleton of
a business. Thus, for a business to exist and compete well, it is
essential for the skeleton to be robust and agile. This paper details
“transformation" from a business perspective, methodologies to bring
about an effective transformation, process-based transformation, and
the role of services computing in this. Further, it details the benefits
that could be achieved through services computing.
Abstract: Fuzzy logic control (FLC) systems have been tested in
many technical and industrial applications as a useful modeling tool
that can handle the uncertainties and nonlinearities of modern control
systems. The main drawback of the FLC methodologies in the
industrial environment is challenging for selecting the number of
optimum tuning parameters.
In this paper, a method has been proposed for finding the optimum
membership functions of a fuzzy system using particle swarm
optimization (PSO) algorithm. A synthetic algorithm combined from
fuzzy logic control and PSO algorithm is used to design a controller
for a continuous stirred tank reactor (CSTR) with the aim of
achieving the accurate and acceptable desired results. To exhibit the
effectiveness of proposed algorithm, it is used to optimize the
Gaussian membership functions of the fuzzy model of a nonlinear
CSTR system as a case study. It is clearly proved that the optimized
membership functions (MFs) provided better performance than a
fuzzy model for the same system, when the MFs were heuristically
defined.
Abstract: Innovation, technology and knowledge are the trilogy
of impact to support the challenges arising from uncertainty.
Evidence showed an opportunity to ask how to manage in this
environment under constant innovation. In an attempt to get a
response from the field of Management Sciences, based in the
Contingency Theory, a research was conducted, with
phenomenological and descriptive approaches, using the Case Study
Method and the usual procedures for this task involving a focus
group composed of managers and employees working in the
pharmaceutical field. The problem situation was raised; the state of
the art was interpreted and dissected the facts. In this tasks were
involved four establishments. The result indicates that these focused
ventures have been managed by its founder empirically and is
experimenting agility described in this work. The expectation of this
study is to improve concepts for stakeholders on creativity in
business.
Abstract: This paper discusses the issues and challenge that
academia faced in knowledge sharing at a research university in
Malaysia. The partial results of interview are presented from the
actual study. The main issues in knowledge sharing practices are
university structure and designation and title. The academia
awareness in sharing knowledge is also influenced by culture. Our
investigation highlight that the concept of reciprocal relationship of
sharing knowledge may hinder knowledge sharing awareness among
academia. Hence, we concluded that further investigation could be
carried out on the social interaction and trust culture among academia
in sharing knowledge within research/ranking university
environment.
Abstract: To improve the material characteristics of single- and
poly-crystals of pure copper, the respective relationships between crystallographic orientations and microstructures, and the bending and mechanical properties were examined. And texture distribution is also
analyzed. A grain refinement procedure was performed to obtain a
grained structure. Furthermore, some analytical results related to
crystal direction maps, inverse pole figures, and textures were obtained from SEM-EBSD analyses. Results showed that these
grained metallic materials have peculiar springback characteristics with various bending angles.