Abstract: Motor imagery classification provides an important basis for designing Brain Machine Interfaces [BMI]. A BMI captures and decodes brain EEG signals and transforms human thought into actions. The ability of an individual to control his EEG through imaginary mental tasks enables him to control devices through the BMI. This paper presents a method to design a four state BMI using EEG signals recorded from the C3 and C4 locations. Principle features extracted through principle component analysis of the segmented EEG are analyzed using two novel classification algorithms using Elman recurrent neural network and functional link neural network. Performance of both classifiers is evaluated using a particle swarm optimization training algorithm; results are also compared with the conventional back propagation training algorithm. EEG motor imagery recorded from two subjects is used in the offline analysis. From overall classification performance it is observed that the BP algorithm has higher average classification of 93.5%, while the PSO algorithm has better training time and maximum classification. The proposed methods promises to provide a useful alternative general procedure for motor imagery classification
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: This article describes Uruk, the virtual museum of
Iraq that we developed for visual exploration and retrieval of image
collections. The system largely exploits the loosely-structured
hierarchy of XML documents that provides a useful representation
method to store semi-structured or unstructured data, which does not
easily fit into existing database. The system offers users the
capability to mine and manage the XML-based image collections
through a web-based Graphical User Interface (GUI). Typically, at an
interactive session with the system, the user can browse a visual
structural summary of the XML database in order to select interesting
elements. Using this intermediate result, queries combining structure
and textual references can be composed and presented to the system.
After query evaluation, the full set of answers is presented in a visual
and structured way.
Abstract: Cognitive models allow predicting some aspects of utility
and usability of human machine interfaces (HMI), and simulating
the interaction with these interfaces. The action of predicting is based
on a task analysis, which investigates what a user is required to do
in terms of actions and cognitive processes to achieve a task. Task
analysis facilitates the understanding of the system-s functionalities.
Cognitive models are part of the analytical approaches, that do not
associate the users during the development process of the interface.
This article presents a study about the evaluation of a human
machine interaction with a contextual assistant-s interface using ACTR
and GOMS cognitive models. The present work shows how these
techniques may be applied in the evaluation of HMI, design and
research by emphasizing firstly the task analysis and secondly the
time execution of the task. In order to validate and support our
results, an experimental study of user performance is conducted at
the DOMUS laboratory, during the interaction with the contextual
assistant-s interface. The results of our models show that the GOMS
and ACT-R models give good and excellent predictions respectively
of users performance at the task level, as well as the object level.
Therefore, the simulated results are very close to the results obtained
in the experimental study.
Abstract: The vast rural landscape in the southern United States
is conspicuously characterized by the hedgerow trees or groves. The
patchwork landscape of fields surrounded by high hedgerows is a
traditional and familiar feature of the American countryside.
Hedgerows are in effect linear strips of trees, groves, or woodlands,
which are often critical habitats for wildlife and important for the
visual quality of the landscape. As landscape interfaces, hedgerows
define the spaces in the landscape, give the landscape life and
meaning, and enrich ecologies and cultural heritages of the American
countryside. Although hedgerows were originally intended as fences
and to mark property and townland boundaries, they are not merely
the natural or man-made additions to the landscape--they have
gradually become “naturalized" into the landscape, deeply rooted in
the rural culture, and now formed an important component of the
southern American rural environment. However, due to the ever
expanding real estate industry and high demand for new residential
development, substantial areas of authentic hedgerow landscape in
the southern United States are being urbanized. Using Hudson Farm
as an example, this study illustrated guidelines of how hedgerows can
be integrated into town planning as green infrastructure and
landscape interface to innovate and direct sustainable land use, and
suggest ways in which such vernacular landscapes can be preserved
and integrated into new development without losing their contextual
inspiration.
Abstract: Researches related to standard product model and
development of neutral manufacturing interfaces for numerical
control machines becomes a significant topic since the last 25 years.
In this paper, a detail description of STEP implementation on turnmill
manufacturing has been discussed. It shows requirements of
information contents from ISO14649 data model. It covers to
describe the design of STEP-NC framework applicable to turn-mill
manufacturing. In the framework, EXPRESS-G and UML modeling
tools are used to depict the information contents of the system and
established the bases of information model requirement. A product
and manufacturing data model applicable for STEP compliant
manufacturing. The next generation turn-mill operations
requirements have been represented by a UML diagram. An object
oriented classes of ISO1449 has been developed on Visual Basic dot
NET platform for binding the static information model represented
by the UML diagram. An architect of the proposed system
implementation has been given on the bases of the design and
manufacturing module of STEP-NC interface established. Finally, a
part 21 file process plan generated for an illustration of turn-mill
components.
Abstract: This paper describes a platform that faces the main
research areas for e-learning educational contents. Reusability tackles
the possibility to use contents in different courses reducing costs and
exploiting available data from repositories. In our approach the
production of educational material is based on templates to reuse
learning objects. In terms of interoperability the main challenge lays
on reaching the audience through different platforms. E-learning
solution must track social consumption evolution where nowadays
lots of multimedia contents are accessed through the social networks.
Our work faces it by implementing a platform for generation of
multimedia presentations focused on the new paradigm related to
social media. The system produces videos-courses on top of web
standard SMIL (Synchronized Multimedia Integration Language)
ready to be published and shared. Regarding interfaces it is
mandatory to satisfy user needs and ease communication. To
overcome it the platform deploys virtual teachers that provide natural
interfaces while multimodal features remove barriers to pupils with
disabilities.
Abstract: In order to assess optical fiber reliability in different environmental and stress conditions series of testing are performed simulating overlapping of chemical and mechanical controlled varying factors. Each series of testing may be compared using statistical processing: i.e. Weibull plots. Due to the numerous data to treat, a software application has appeared useful to interpret selected series of experiments in function of envisaged factors. The current paper presents a software application used in the storage, modelling and interpretation of experimental data gathered from optical fibre testing. The present paper strictly deals with the software part of the project (regarding the modelling, storage and processing of user supplied data).
Abstract: Multifunctional structures are a potentially disruptive
technology that allows for significant mass savings on spacecraft.
The specific concept addressed herein is that of a multifunctional
power structure. In this paper, a parametric optimisation of the
design of such a structure that uses commercially available battery
cells is presented. Using numerical modelling, it was found that there
exists several trade-offs aboutthe conflict between the capacity of the
panel and its mechanical properties. It was found that there is no
universal optimal location for the cells. Placing them close to the
mechanical interfaces increases loading in the mechanically weak
cells whereas placing them at the centre of the panel increases the
stress inthe panel and reduces the stiffness of the structure.
Abstract: In our modern world, more physical transactions are being substituted by electronic transactions (i.e. banking, shopping, and payments), many businesses and companies are performing most of their operations through the internet. Instead of having a physical commerce, internet visitors are now adapting to electronic commerce (e-Commerce). The ability of web users to reach products worldwide can be greatly benefited by creating friendly and personalized online business portals. Internet visitors will return to a particular website when they can find the information they need or want easily. Dealing with this human conceptualization brings the incorporation of Artificial/Computational Intelligence techniques in the creation of customized portals. From these techniques, Fuzzy-Set technologies can make many useful contributions to the development of such a human-centered endeavor as e-Commerce. The main objective of this paper is the implementation of a Paradigm for the Intelligent Design and Operation of Human-Computer interfaces. In particular, the paradigm is quite appropriate for the intelligent design and operation of software modules that display information (such Web Pages, graphic user interfaces GUIs, Multimedia modules) on a computer screen. The human conceptualization of the user personal information is analyzed throughout a Cascaded Fuzzy Inference (decision-making) System to generate the User Ascribe Qualities, which identify the user and that can be used to customize portals with proper Web links.
Abstract: This paper introduces a hardware solution to password
exposure problem caused by direct accesses to the keyboard hardware
interfaces through which a possible attacker is able to grab user-s
password even where existing countermeasures are deployed. Several
researches have proposed reasonable software based solutions to the
problem for years. However, recently introduced hardware
vulnerability problems have neutralized the software approaches and
yet proposed any effective software solution to the vulnerability.
Hardware approach in this paper is expected as the only solution to the
vulnerability
Abstract: In this work, we examine fluid mixing in a full three-stream mixing channel with longitudinal vortex generators (LVGs) built on the channel bottom by numerical simulation and experiment. The effects of the asymmetrical arrangement and the attack angle of the LVGs on fluid mixing are investigated. The results show that the micromixer with LVGs at a small asymmetry index (defined by the ratio of the distance from the center plane of the gap between the winglets to the center plane of the main channel to the width of the main channel) is superior to the micromixer with symmetric LVGs and that with LVGs at a large asymmetry index. The micromixer using five mixing modules of the LVGs with an attack angle between 16.5 degrees and 22.5 degrees can achieve excellent mixing over a wide range of Reynolds numbers. Here, we call a section of channel with two pairs of staggered asymmetrical LVGs a mixing module. Besides, the micromixer with LVGs at a small attack angle is more efficient than that with a larger attack angle when pressure losses are taken into account.
Abstract: Context awareness is a capability whereby mobile
computing devices can sense their physical environment and adapt
their behavior accordingly. The term context-awareness, in
ubiquitous computing, was introduced by Schilit in 1994 and has
become one of the most exciting concepts in early 21st-century
computing, fueled by recent developments in pervasive computing
(i.e. mobile and ubiquitous computing). These include computing
devices worn by users, embedded devices, smart appliances, sensors
surrounding users and a variety of wireless networking technologies.
Context-aware applications use context information to adapt
interfaces, tailor the set of application-relevant data, increase the
precision of information retrieval, discover services, make the user
interaction implicit, or build smart environments. For example: A
context aware mobile phone will know that the user is currently in a
meeting room, and reject any unimportant calls. One of the major
challenges in providing users with context-aware services lies in
continuously monitoring their contexts based on numerous sensors
connected to the context aware system through wireless
communication. A number of context aware frameworks based on
sensors have been proposed, but many of them have neglected the
fact that monitoring with sensors imposes heavy workloads on
ubiquitous devices with limited computing power and battery. In this
paper, we present CALEEF, a lightweight and energy efficient
context aware framework for resource limited ubiquitous devices.
Abstract: Finger spelling is an art of communicating by signs
made with fingers, and has been introduced into sign language to serve
as a bridge between the sign language and the verbal language.
Previous approaches to finger spelling recognition are classified into
two categories: glove-based and vision-based approaches. The
glove-based approach is simpler and more accurate recognizing work
of hand posture than vision-based, yet the interfaces require the user to
wear a cumbersome and carry a load of cables that connected the
device to a computer. In contrast, the vision-based approaches provide
an attractive alternative to the cumbersome interface, and promise
more natural and unobtrusive human-computer interaction. The
vision-based approaches generally consist of two steps: hand
extraction and recognition, and two steps are processed independently.
This paper proposes real-time vision-based Korean finger spelling
recognition system by integrating hand extraction into recognition.
First, we tentatively detect a hand region using CAMShift algorithm.
Then fill factor and aspect ratio estimated by width and height
estimated by CAMShift are used to choose candidate from database,
which can reduce the number of matching in recognition step. To
recognize the finger spelling, we use DTW(dynamic time warping)
based on modified chain codes, to be robust to scale and orientation
variations. In this procedure, since accurate hand regions, without
holes and noises, should be extracted to improve the precision, we use
graph cuts algorithm that globally minimize the energy function
elegantly expressed by Markov random fields (MRFs). In the
experiments, the computational times are less than 130ms, and the
times are not related to the number of templates of finger spellings in
database, as candidate templates are selected in extraction step.
Abstract: This article presents a simple way to perform programmed voice commands for the interface with commercial Digital and Analogue Input/Output PCI cards, used in Robotics and Automation applications. Robots and Automation equipment can "listen" to voice commands and perform several different tasks, approaching to the human behavior, and improving the human- machine interfaces for the Automation Industry. Since most PCI Digital and Analogue Input/Output cards are sold with several DLLs included (for use with different programming languages), it is possible to add speech recognition capability, using a standard speech recognition engine, compatible with the programming languages used. It was created in this work a Visual Basic 6 (the world's most popular language) application, that listens to several voice commands, and is capable to communicate directly with several standard 128 Digital I/O PCI Cards, used to control complete Automation Systems, with up to (number of boards used) x 128 Sensors and/or Actuators.
Abstract: Human computer interaction has progressed
considerably from the traditional modes of interaction. Vision based
interfaces are a revolutionary technology, allowing interaction
through human actions, gestures. Researchers have developed
numerous accurate techniques, however, with an exception to few
these techniques are not evaluated using standard HCI techniques. In
this paper we present a comprehensive framework to address this
issue. Our evaluation of a computer vision application shows that in
addition to the accuracy, it is vital to address human factors
Abstract: The wireless adhoc network is comprised of wireless
node which can move freely and are connected among themselves
without central infrastructure. Due to the limited transmission range
of wireless interfaces, in most cases communication has to be relayed
over intermediate nodes. Thus, in such multihop network each node
(also called router) is independent, self-reliant and capable to route
the messages over the dynamic network topology. Various protocols
are reported in this field and it is very difficult to decide the best one.
A key issue in deciding which type of routing protocol is best for
adhoc networks is the communication overhead incurred by the
protocol. In this paper STAR a table driven and DSR on demand
protocols based on IEEE 802.11 are analyzed for their performance
on different performance measuring metrics versus varying traffic
CBR load using QualNet 5.0.2 network simulator.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: This paper presents three models which enable the
customisation of Universal Description, Discovery and Integration
(UDDI) query results, based on some pre-defined and/or real-time
changing parameters. These proposed models detail the requirements,
design and techniques which make ranking of Web service discovery
results from a service registry possible. Our contribution is two fold:
First, we present an extension to the UDDI inquiry capabilities. This
enables a private UDDI registry owner to customise or rank the query
results, based on its business requirements. Second, our proposal
utilises existing technologies and standards which require minimal
changes to existing UDDI interfaces or its data structures. We believe
these models will serve as valuable reference for enhancing the
service discovery methods within a private UDDI registry
environment.