Abstract: This paper addresses the problem of peak-to-average
power ratio (PAPR) in orthogonal frequency division multiplexing
(OFDM) systems. It also introduces a new PAPR reduction technique
based on adaptive square-rooting (SQRT) companding process. The
SQRT process of the proposed technique changes the statistical
characteristics of the OFDM output signals from Rayleigh
distribution to Gaussian-like distribution. This change in statistical
distribution results changes of both the peak and average power
values of OFDM signals, and consequently reduces significantly the
PAPR. For the 64QAM OFDM system using 512 subcarriers, up to 6
dB reduction in PAPR was achieved by square-rooting technique
with fixed degradation in bit error rate (BER) equal to 3 dB.
However, the PAPR is reduced at the expense of only -15 dB out-ofband
spectral shoulder re-growth below the in-band signal level. The
proposed adaptive SQRT technique is superior in terms of BER
performance than the original, non-adaptive, square-rooting
technique when the required reduction in PAPR is no more than 5
dB. Also, it provides fixed amount of PAPR reduction in which it is
not available in the original SQRT technique.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: The blood ducts must be occluded to avoid loss of
blood from vessels in laparoscopic surgeries. This paper presents a
locking mechanism to be used in a ligation laparoscopic procedure
(LigLAP I), as an alternative solution for a stapling procedure.
Currently, stapling devices are being used to occlude vessels. Using
these devices may result in some problems, including injury of bile
duct, taking up a great deal of space behind the vessel, and bile leak.
In this new procedure, a two-layer suture occludes a vessel. A
locking mechanism is also required to hold the suture. Since there is
a limited space at the device tip, a Shape Memory Alloy (SMA)
actuator is used in this mechanism. Suitability for cleanroom
applications, small size, and silent performance are among the
advantages of SMA actuators in biomedical applications. An
experimental study is conducted to examine the function of the
locking mechanism. To set up the experiment, a prototype of a
locking mechanism is built using nitinol, which is a nickel-titanium
shape memory alloy. The locking mechanism successfully locks a
polymer suture for all runs of the experiment. In addition, the effects
of various surface materials on the applied pulling forces are studied.
Various materials are mounted at the mechanism tip to compare the
maximum pulling forces applied to the suture for each material. The
results show that the various surface materials on the device tip
provide large differences in the applied pulling forces.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: This paper proposes a method for speckle reduction in
medical ultrasound imaging while preserving the edges with the
added advantages of adaptive noise filtering and speed. A nonlinear
image diffusion method that incorporates local image parameter,
namely, scatterer density in addition to gradient, to weight the
nonlinear diffusion process, is proposed. The method was tested for
the isotropic case with a contrast detail phantom and varieties of
clinical ultrasound images, and then compared to linear and some
other diffusion enhancement methods. Different diffusion parameters
were tested and tuned to best reduce speckle noise and preserve
edges. The method showed superior performance measured both
quantitatively and qualitatively when incorporating scatterer density
into the diffusivity function. The proposed filter can be used as a
preprocessing step for ultrasound image enhancement before
applying automatic segmentation, automatic volumetric calculations,
or 3D ultrasound volume rendering.
Abstract: With getting older in the whole population, the
prevalence of stroke and its residual disability is getting higher and
higher recently in Taiwan. The functional electrical stimulation
cycling system (FESCS) is useful for hemiplegic patients. Because
that the muscle of stroke patients is under hybrid activation. The raw
electromyography (EMG) represents the residual muscle force of
stroke subject whereas the peak-to-peak of stimulus EMG indicates the
force enhancement benefiting from ES. It seems that EMG signals
could be used for a parameter of feedback control mechanism. So, we
design the feedback control protocol of FESCS, it includes
physiological signal recorder, FPGA biomedical module, DAC and
electrical stimulation circuit. Using the intensity of real-time EMG
signal obtained from patients, as a feedback control method for the
output voltage of FES-cycling system.
Abstract: This study systemizes processes and methods in
wooden furniture design that contains uniqueness in function and
aesthetics. The study was done by research and analysis for
designer-s consideration factors that affect function and production.
Therefore, the study result indicates that such factors are design
process (planning for design, product specifications, concept design,
product architecture, industrial design, production), design evaluation
as well as wooden furniture design dependent factors i.e. art (art
style; furniture history, form), functionality (the strength and
durability, area place, using), material (appropriate to function, wood
mechanical properties), joints, cost, safety, and social responsibility.
Specifically, all aforementioned factors affect good design. Resulting
from direct experience gained through user-s usage, the designer
must design the wooden furniture systemically and effectively. As a
result, this study selected dinning armchair as a case study with all
involving factors and all design process stated in this study.
Abstract: The ability to distinguish missense nucleotide
substitutions that contribute to harmful effect from those that do not
is a difficult problem usually accomplished through functional in
vivo analyses. In this study, instead current biochemical methods, the
effects of missense mutations upon protein structure and function
were assayed by means of computational methods and information
from the databases. For this order, the effects of new missense
mutations in exon 5 of PTEN gene upon protein structure and
function were examined. The gene coding for PTEN was identified
and localized on chromosome region 10q23.3 as the tumor
suppressor gene. The utilization of these methods were shown that
c.319G>A and c.341T>G missense mutations that were recognized in
patients with breast cancer and Cowden disease, could be pathogenic.
This method could be use for analysis of missense mutation in others
genes.
Abstract: The study of piezoelectric material in the past was in T-Domain form; however, no one has studied piezoelectric material in the S-Domain form. This paper will present the piezoelectric material in the transfer function or S-Domain model. S-Domain is a well known mathematical model, used for analyzing the stability of the material and determining the stability limits. By using S-Domain in testing stability of piezoelectric material, it will provide a new tool for the scientific world to study this material in various forms.
Abstract: This paper proposes a novel frequency offset (FO) estimator for orthogonal frequency division multiplexing. Simplicity is most significant feature of this algorithm and can be repeated to achieve acceptable accuracy. Also fractional and integer part of FO is estimated jointly with use of the same algorithm. To do so, instead of using conventional algorithms that usually use correlation function, we use DFT of received signal. Therefore, complexity will be reduced and we can do synchronization procedure by the same hardware that is used to demodulate OFDM symbol. Finally, computer simulation shows that the accuracy of this method is better than other conventional methods.
Abstract: This paper describes the optimization of a complex
dairy farm simulation model using two quite different methods of
optimization, the Genetic algorithm (GA) and the Lipschitz
Branch-and-Bound (LBB) algorithm. These techniques have been
used to improve an agricultural system model developed by Dexcel
Limited, New Zealand, which describes a detailed representation of
pastoral dairying scenarios and contains an 8-dimensional parameter
space. The model incorporates the sub-models of pasture growth and
animal metabolism, which are themselves complex in many cases.
Each evaluation of the objective function, a composite 'Farm
Performance Index (FPI)', requires simulation of at least a one-year
period of farm operation with a daily time-step, and is therefore
computationally expensive. The problem of visualization of the
objective function (response surface) in high-dimensional spaces is
also considered in the context of the farm optimization problem.
Adaptations of the sammon mapping and parallel coordinates
visualization are described which help visualize some important
properties of the model-s output topography. From this study, it is
found that GA requires fewer function evaluations in optimization
than the LBB algorithm.
Abstract: This paper presents positive and negative full-wave
rectifier. The proposed structure is based on OTA using
commercially available ICs (LT1228). The features of the proposed
circuit are that: it can rectify and amplify voltage signal with
controllable output magnitude via input bias current: the output
voltage is free from temperature variation. The circuit description
merely consists of 1 single ended and 3 fully differential OTAs. The
performance of the proposed circuit are investigated though PSpice.
They show that the proposed circuit can function as positive/negative
full-wave rectifier, where the voltage input wide-dynamic range from
-5V to 5V. Furthermore, the output voltage is slightly dependent on
the temperature variations.
Abstract: Due to the deregulation of the Electric Supply
Industry and the resulting emergence of electricity market, the
volumes of power purchases are on the rise all over the world. In a
bid to meet the customer-s demand in a reliable and yet economic
manner, utilities purchase power from the energy market over and
above its own production. This paper aims at developing an optimal
power purchase model with two objectives viz economy and
environment ,taking various functional operating constraints such as
branch flow limits, load bus voltage magnitudes limits, unit capacity
constraints and security constraints into consideration.The price of
purchased power being an uncertain variable is modeled using fuzzy
logic. DEMO (Differential Evolution For Multi-objective
Optimization) is used to obtain the pareto-optimal solution set of the
multi-objective problem formulated. Fuzzy set theory has been
employed to extract the best compromise non-dominated solution.
The results obtained on IEEE 30 bus system are presented and
compared with that of NSGAII.
Abstract: In this paper, the C1-conforming finite element method is analyzed for a class of nonlinear fourth-order hyperbolic partial differential equation. Some a priori bounds are derived using Lyapunov functional, and existence, uniqueness and regularity for the weak solutions are proved. Optimal error estimates are derived for both semidiscrete and fully discrete schemes.
Abstract: Wireless mobile communications have experienced
the phenomenal growth through last decades. The advances in
wireless mobile technologies have brought about a demand for high
quality multimedia applications and services. For such applications
and services to work, signaling protocol is required for establishing,
maintaining and tearing down multimedia sessions. The Session
Initiation Protocol (SIP) is an application layer signaling protocols,
based on request/response transaction model. This paper considers
SIP INVITE transaction over an unreliable medium, since it has been
recently modified in Request for Comments (RFC) 6026. In order to
help in assuring that the functional correctness of this modification is
achieved, the SIP INVITE transaction is modeled and analyzed using
Colored Petri Nets (CPNs). Based on the model analysis, it is
concluded that the SIP INVITE transaction is free of livelocks and
dead codes, and in the same time it has both desirable and
undesirable deadlocks. Therefore, SIP INVITE transaction should be
subjected for additional updates in order to eliminate undesirable
deadlocks. In order to reduce the cost of implementation and
maintenance of SIP, additional remodeling of the SIP INVITE
transaction is recommended.
Abstract: The model-based approach to user interface design relies on developing separate models that are capturing various aspects about users, tasks, application domain, presentation and dialog representations. This paper presents a task modeling approach for user interface design and aims at exploring the mappings between task, domain and presentation models. The basic idea of our approach is to identify typical configurations in task and domain models and to investigate how they relate each other. A special emphasis is put on application-specific functions and mappings between domain objects and operational task structures. In this respect, we will distinguish between three layers in the task decomposition: a functional layer, a planning layer, and an operational layer.
Abstract: In this paper newly reported Cosh window function is
used in the design of prototype filter for M-channel Near Perfect
Reconstruction (NPR) Cosine Modulated Filter Bank (CMFB). Local
search optimization algorithm is used for minimization of distortion
parameters by optimizing the filter coefficients of prototype filter.
Design examples are presented and comparison has been made with
Kaiser window based filterbank design of recently reported work.
The result shows that the proposed design approach provides lower
distortion parameters and improved far-end suppression than the
Kaiser window based design of recent reported work.
Abstract: The clustering ensembles combine multiple partitions
generated by different clustering algorithms into a single clustering
solution. Clustering ensembles have emerged as a prominent method
for improving robustness, stability and accuracy of unsupervised
classification solutions. So far, many contributions have been done to
find consensus clustering. One of the major problems in clustering
ensembles is the consensus function. In this paper, firstly, we
introduce clustering ensembles, representation of multiple partitions,
its challenges and present taxonomy of combination algorithms.
Secondly, we describe consensus functions in clustering ensembles
including Hypergraph partitioning, Voting approach, Mutual
information, Co-association based functions and Finite mixture
model, and next explain their advantages, disadvantages and
computational complexity. Finally, we compare the characteristics of
clustering ensembles algorithms such as computational complexity,
robustness, simplicity and accuracy on different datasets in previous
techniques.
Abstract: Fixed-bed slow pyrolysis experiments of rice husk
have been conducted to determine the effect of pyrolysis
temperature, heating rate, particle size and reactor length on the
pyrolysis product yields. Pyrolysis experiments were performed at
pyrolysis temperature between 400 and 600°C with a constant
heating rate of 60°C/min and particle sizes of 0.60-1.18 mm. The
optimum process conditions for maximum liquid yield from the rice
husk pyrolysis in a fixed bed reactor were also identified. The highest
liquid yield was obtained at a pyrolysis temperature of 500°C,
particle size of
1.18-1.80 mm, with a heating rate of 60°C/min in a 300 mm length
reactor. The obtained yield of, liquid, gas and solid were found be in
the range of 22.57-31.78 %, 27.75-42.26 % and 34.17-42.52 % (all
weight basics) respectively at different pyrolysis conditions. The
results indicate that the effects of pyrolysis temperature and particle
size on the pyrolysis yield are more significant than that of heating
rate and reactor length. The functional groups and chemical
compositions present in the liquid obtained at optimum conditions
were identified by Fourier Transform-Infrared (FT-IR) spectroscopy
and Gas Chromatography/ Mass Spectroscopy (GC/MS) analysis
respectively.