Abstract: Two micromechanical models for 3D smart composite
with embedded periodic or nearly periodic network of generally
orthotropic reinforcements and actuators are developed and applied to
cubic structures with unidirectional orientation of constituents.
Analytical formulas for the effective piezothermoelastic coefficients
are derived using the Asymptotic Homogenization Method (AHM).
Finite Element Analysis (FEA) is subsequently developed and used
to examine the aforementioned periodic 3D network reinforced smart
structures. The deformation responses from the FE simulations are
used to extract effective coefficients. The results from both
techniques are compared. This work considers piezoelectric materials
that respond linearly to changes in electric field, electric
displacement, mechanical stress and strain and thermal effects. This
combination of electric fields and thermo-mechanical response in
smart composite structures is characterized by piezoelectric and
thermal expansion coefficients. The problem is represented by unitcell
and the models are developed using the AHM and the FEA to
determine the effective piezoelectric and thermal expansion
coefficients. Each unit cell contains a number of orthotropic
inclusions in the form of structural reinforcements and actuators.
Using matrix representation of the coupled response of the unit cell,
the effective piezoelectric and thermal expansion coefficients are
calculated and compared with results of the asymptotic
homogenization method. A very good agreement is shown between
these two approaches.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: The purpose of this work is to optimize a Switched Reluctance Motor (SRM) for an automotive application, specifically for a fully electric car. A new optimization approach is proposed. This unique approach transforms automotive customer requirements into an optimization problem, based on sound knowledge of a SRM theory. The approach combines an analytical and a finite element analysis of the motor to quantify static nonlinear and dynamic performance parameters, as phase currents and motor torque maps, an output power and power losses in order to find the optimal motor as close to the reality as possible, within reasonable time. The new approach yields the optimal motor which is competitive with other types of already proposed motors for automotive applications. This distinctive approach can also be used to optimize other types of electrical motors, when parts specifically related to the SRM are adjusted accordingly.
Abstract: It is necessary to manage the fatigue crack growth (FCG) once those cracks are detected during in-service inspections. In this paper, a simulation program (FCG-System) is developed utilizing the commercial software ABAQUS with its object-oriented programming interface to simulate the fatigue crack path and to compute the corresponding fatigue life. In order to apply FCG-System in large-scale marine structures, the substructure modeling technique is integrated in the system under the consideration of structural details and load shedding during crack growth. Based on the nodal forces and nodal displacements obtained from finite element analysis, a formula for shell elements to compute stress intensity factors is proposed in the view of virtual crack closure technique. The cracks initiating from the intersection of flange and the end of the web-stiffener are investigated for fatigue crack paths and growth lives under water pressure loading and axial force loading, separately. It is found that the FCG-System developed by authors could be an efficient tool to perform fatigue crack growth analysis on marine structures.
Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: Non-linear FEM calculations are indispensable when important technical information like operating performance of a rubber component is desired. Rubber bumpers built into air-spring structures may undergo large deformations under load, which in itself shows non-linear behavior. The changing contact range between the parts and the incompressibility of the rubber increases this non-linear behavior further. The material characterization of an elastomeric component is also a demanding engineering task. In this paper a comprehensive investigation is introduced including laboratory measurements, mesh density analysis and complex finite element simulations to obtain the load-displacement curve of the chosen rubber bumper. Contact and friction effects are also taken into consideration. The aim of this research is to elaborate a FEM model which is accurate and competitive for a future shape optimization task.
Abstract: Outrigger-braced wall systems are commonly used to provide high rise buildings with the required lateral stiffness for wind and earthquake resistance. The existence of outriggers adds to the stiffness and strength of walls as reported by several studies. The effects of different parameters on the elasto-plastic dynamic behavior of outrigger-braced wall systems to earthquakes are investigated in this study. Parameters investigated include outrigger stiffness, concrete strength, and reinforcement arrangement as the main design parameters in wall design. In addition to being significantly affect the wall behavior, such parameters may lead to the change of failure mode and the delay of crack propagation and consequently failure as the wall is excited by earthquakes. Bi-linear stress-strain relation for concrete with limited tensile strength and truss members with bi-linear stress-strain relation for reinforcement were used in the finite element analysis of the problem. The famous earthquake record, El-Centro, 1940 is used in the study. Emphasize was given to the lateral drift, normal stresses and crack pattern as behavior controlling determinants. Results indicated significant effect of the studied parameters such that stiffer outrigger, higher grade concrete and concentrating the reinforcement at wall edges enhance the behavior of the system. Concrete stresses and cracking behavior are too much enhanced while less drift improvements are observed.
Abstract: To understand the factors which affect impact damage on composite structures, particularly the effects of impact position and ribs. In this paper, a finite element model (FEM) of low-velocity impact damage on the composite structure was established via the nonlinear finite element method, combined with the user-defined materials subroutine (VUMAT) of the ABAQUS software. The structural elements chosen for the investigation comprised a series of stiffened composite panels, representative of real aircraft structure. By impacting the panels at different positions relative to the ribs, the effect of relative position of ribs was found out. Then the simulation results and the experiments data were compared. Finally, the factors which affect impact damage on the structures were discussed. The paper was helpful for the design of stiffened composite structures.
Abstract: A mechanically-resonant torsional spring scanner was developed in a recent study. Various methods were developed to improve the angular displacement of the scanner while maintaining the scanner frequency. However the effects of rotor magnet radial position on scanner characteristics were not well investigated. In this study, the relationships between the magnet position and the scanner characteristics such as natural frequency, angular displacement and stress level were studied. A finite element model was created and an average deviation of 3.18% was found between the simulation and experimental results, qualifying the simulation results as a guide for further investigations. Three magnet positions on the transverse oscillating suspended plate were investigated by finite element analysis (FEA) and one of the positions were selected as the design position. The magnet position with the longest distance from the twist axis of mirror was selected since it attains minimum stress level, while exceeding the minimum critical flicker frequency and delivering the targeted angular displacement to the scanner.
Abstract: In this paper, the behavior of different types of DST columns has been studied under bending load. Briefly, composite columns consist of an internal carbon steel tube and an external stainless steel wall that the between the walls are filled with concrete. Composite columns are expected to combine the advantages of all three materials and have the advantage of high flexural stiffness of CFDST columns. In this research, ABAQUS software is used for finite element analysis then the results of ultimate strength of the composite sections are illustrated.
Abstract: In this paper, the elasto-plastic and cyclic torsion of a shaft is studied using a finite element method. The Prager kinematic hardening theory of plasticity with the Ramberg and Osgood stress-strain equation is used to evaluate the cyclic loading behavior of the shaft under the torsional loading. The material of shaft is assumed to follow the non-linear strain hardening property based on the Prager model. The finite element method with C1 continuity is developed and used for solution of the governing equations of the problem. The successive substitution iterative method is used to calculate the distribution of stresses and plastic strains in the shaft due to cyclic loads. The shear stress, effective stress, residual stress and elastic and plastic shear strain distribution are presented in the numerical results.
Abstract: This study presents the optimal design and formulation of a kinematic model of a flexible slider crank mechanism. The objective of the proposed innovative design is to take extra advantage of the compliant mechanism and maximize the fatigue life by applying the Taguchi method. A formulated kinematic model is developed using a pseudo-rigid-body model (PRBM). By means of mathematic models, the kinematic behaviors of the flexible slider crank mechanism are captured using MATLAB software. Finite element analysis (FEA) is used to show the stress distribution. The results show that the optimal shape of the flexible hinge includes a force of 8.5N, a width of 9mm and a thickness of 1.1mm. Analysis of variance shows that the thickness of the proposed hinge is the most significant parameter, with an F test of 15.5. Finally, a prototype is manufactured to prepare for testing the kinematic and dynamic behaviors.
Abstract: Since torque ripple is the main cause of noise and vibrations, the performance of Switched Reluctance Motor (SRM) can be improved by minimizing its torque ripple using a novel control technique called Direct Torque Control (DTC). In DTC technique, torque is controlled directly through control of magnitude of the flux and change in speed of the stator flux vector. The flux and torque are maintained within set hysteresis bands.
The DTC of SRM is analyzed by two methods. In one method, the actual torque is computed by conducting Finite Element Analysis (FEA) on the design specifications of the motor. In the other method, the torque is computed by Simplified Torque Equation. The variation of peak current, average current, torque ripple and speed settling time with Simplified Torque Equation model is compared with FEA based model.
Abstract: This paper explains the results of an investigation on the analysis of flush end plate steel connections by means of finite element method. Flush end plates are a highly indeterminate type of connection, which have a number of parameters that affect their behavior. Because of this, experimental investigations are complicated and very costly. Today, the finite element method provides an ideal method for analyzing complicated structures. Finite element models of these types of connections under monotonic loading have previously been investigated. A numerical model, which can predict the cyclic behavior of these connections, is of critical importance, as dynamic experiments are more costly. This paper summarizes a study to develop a three-dimensional finite element model that can accurately capture the cyclic behavior of flush end plate connections. Comparisons between FEM results and experimental results obtained from full-scale tests have been carried out, which confirms the accuracy of the finite element model. Consequently, design equations for this connection have been investigated and it is shown that these predictions are not precise in all cases. The effect of end plate thickness and bolt diameter on the overall behavior of this connection is discussed. This research demonstrates that using the appropriate configuration, this connection has the potential to form a plastic hinge in the beam--desirable in seismic behavior.
Abstract: Accurate dynamic modeling and analysis of flexible link manipulator (FLM) with non linear dynamics is very difficult due to distributed link flexibility and few studies have been conducted based on assumed modes method (AMM) and finite element models. In this paper a nonlinear dynamic model with first two elastic modes is derived using combined Euler/Lagrange and AMM approaches. Significant dynamics associated with the system such as hub inertia, payload, structural damping, friction at joints, combined link and joint flexibility are incorporated to obtain the complete and accurate dynamic model. The response of the FLM to the applied bang-bang torque input is compared against the models derived from LS-DYNA finite element discretization approach and linear finite element models. Dynamic analysis is conducted using LS-DYNA finite element model which uses the explicit time integration scheme to simulate the system. Parametric study is conducted to show the impact payload mass. A numerical result shows that the LS-DYNA model gives the smooth hub-angle profile.
Abstract: Steel bracing members are widely used in steel
structures to reduce lateral displacement and dissipate energy during
earthquake motions. Concentric steel bracing provide an excellent
approach for strengthening and stiffening steel buildings. Using these
braces the designer can hardly adjust the stiffness together with
ductility as needed because of buckling of braces in compression. In
this study the use of SMA bracing and steel bracing (Mega) utilized
in steel frames are investigated. The effectiveness of these two
systems in rehabilitating a mid-rise eight-storey steel frames were
examined using time-history nonlinear analysis utilizing seismostruct
software. Results show that both systems improve the strength and
stiffness of the original structure but due to excellent behavior of
SMA in nonlinear phase and under compressive forces this system
shows much better performance than the rehabilitation system of
Mega bracing.
Abstract: The numerical simulation of the crack welding process is reported in this paper. The thermo-electro-structural coupled-field finite element analysis is adopted to investigate the welding process of crack surfaces. In the simulation, the pressure-dependent and temperature-dependent electrical contact conditions are considered. From the results, the crack surfaces can melt and weld together under the compressive load and electric current. The contact pressure effect must be considered in the finite element analysis to obtain more practical results.
Abstract: The performance of a machine tool is eventually assessed by its ability to produce a component of the required geometry in minimum time and at small operating cost. It is customary to base the structural design of any machine tool primarily upon the requirements of static rigidity and minimum natural frequency of vibration. The operating properties of machines like cutting speed, feed and depth of cut as well as the size of the work piece also have to be kept in mind by a machine tool structural designer. This paper presents a novel approach to the design of machine tool column for static and dynamic rigidity requirement. Model evaluation is done effectively through use of General Finite Element Analysis software ANSYS. Studies on machine tool column are used to illustrate finite element based concept evaluation technique. This paper also presents results obtained from the computations of thin walled box type columns that are subjected to torsional and bending loads in case of static analysis and also results from modal analysis. The columns analyzed are square and rectangle based tapered open column, column with cover plate, horizontal partitions and with apertures. For the analysis purpose a total of 70 columns were analyzed for bending, torsional and modal analysis. In this study it is observed that the orientation and aspect ratio of apertures have no significant effect on the static and dynamic rigidity of the machine tool structure.