Abstract: Trace element speciation of an integrated soil
amendment matrix was studied with a modified BCR sequential
extraction procedure. The analysis included pseudo-total
concentration determinations according to USEPA 3051A and
relevant physicochemical properties by standardized methods. Based
on the results, the soil amendment matrix possessed neutralization
capacity comparable to commercial fertilizers. Additionally, the
pseudo-total concentrations of all trace elements included in the
Finnish regulation for agricultural fertilizers were lower than the
respective statutory limit values. According to chemical speciation,
the lability of trace elements increased in the following order: Hg <
Cr < Co < Cu < As < Zn < Ni < Pb < Cd < V < Mo < Ba. The
validity of the BCR approach as a tool for chemical speciation was
confirmed by the additional acid digestion phase. Recovery of trace
elements during the procedure assured the validity of the approach
and indicated good quality of the analytical work.
Abstract: An experiment was conducted in October 2008 due the ability replacement plant associate biofertilizers by chemical fertilizers and the qualifying rate of chemical N fertilizers at the moment of using this biofertilizers and the interaction of this biofertilizer on each other. This field experiment has been done in Persepolis (Throne of Jamshid) and arrange by using factorial with the basis of randomized complete block design, in three replication Azespirilium SP bacteria has been admixed with consistence 108 cfu/g and inoculated with seeds of wheat, The streptomyces SP has been used in amount of 550 gr/ha and concatenated on clay and for the qualifying range of chemical fertilizer 4 level of N chemical fertilizer from the source of urea (N0=0, N1=60, N2=120, N3=180) has been used in this experiment. The results indicated there were Significant differences between levels of Nitrogen fertilizer in the entire characteristic which has been measured in this experiment. The admixed Azespirilium SP showed significant differences between their levels in the characteristics such as No. of fertile ear, No. of grain per ear, grain yield, grain protein percentage, leaf area index and the agronomic fertilizer use efficiency. Due the interaction streptomyses with Azespirilium SP bacteria this actinomycet didn-t show any statistically significant differences between it levels.
Abstract: Medicinal plants are most suitable crops for ecological production systems because of their role in human health and the aim of sustainable agriculture to improve ecosystem efficiency and its products quality. Calculations include energy output (contents of energy in seed) and energy inputs (consumption of fertilizers, pesticides, labor, machines, fuel and electricity). The ratio of output of the production to inputs is called the energy outputs / inputs ratio or energy efficiency. One way to quantify essential parts of agricultural development is the energy flow method. The output / input energy ratio is proposed as the most comprehensive single factor in pursuing the objective of sustainability. Sylibum marianum L. is one of the most important medicinal plants in Iran and has effective role on health of growing population in Iran. The objective of this investigation was to find out energy efficiency in conventional and low input production system of Milk thistle. This investigation was carried out in the spring of 2005 – 2007 in the Research Station of Rangelands in Hamand - Damavand region of IRAN. This experiment was done in split-split plot based on randomized complete block design with 3 replications. Treatments were 2 production systems (Conventional and Low input system) in the main plots, 3 planting time (25 of March, 4 and 14 of April) in the sub plots and 2 seed types (Improved and Native of Khoozestan) in the sub-sub plots. Results showed that in conventional production system energy efficiency, because of higher inputs and less seed yield, was less than low input production system. Seed yield was 1199.5 and 1888 kg/ha in conventional and low input systems, respectively. Total energy inputs and out puts for conventional system was 10068544.5 and 7060515.9 kcal. These amounts for low input system were 9533885.6 and 11113191.8 kcal. Results showed that energy efficiency for seed production in conventional and low input system was 0.7 and 1.16, respectively. So, milk thistle seed production in low input system has 39.6 percent higher energy efficiency than conventional production system. Also, higher energy efficiency were found in sooner planting time (25 of March) and native seed of Khoozestan.
Abstract: In order to study the effect of phosphate solubilization
microorganisms (PSM) and plant growth promoting rhizobacteria
(PGPR) on yield and yield components of corn Zea mays (L. cv.
SC604) an experiment was conducted at research farm of Sari
Agricultural Sciences and Natural Resources University, Iran during
2007. Experiment laid out as split plot based on randomized
complete block design with three replications. Three levels of
manures (consisted of 20 Mg.ha-1 farmyard manure, 15 Mg.ha-1 green
manure and check or without any manures) as main plots and eight
levels of biofertilizers (consisted of 1-NPK or conventional fertilizer
application; 2-NPK+PSM+PGPR; 3 NP50%K+PSM+PGPR; 4-
N50%PK+PSM +PGPR; 5-N50%P50%K+PSM+ PGPR; 6-PK+PGPR; 7-
NK+PSM and 8-PSM+PGPR) as sub plots were treatments. Results
showed that farmyard manure application increased row number, ear
weight, grain number per ear, grain yield, biological yield and
harvest index compared to check. Furthermore, using of PSM and
PGPR in addition to conventional fertilizer applications (NPK) could
improve ear weight, row number and grain number per row and
ultimately increased grain yield in green manure and check plots.
According to results in all fertilizer treatments application of PSM
and PGPR together could reduce P application by 50% without any
significant reduction of grain yield. However, this treatment could
not compensate 50% reduction of N application.
Abstract: Recent research on seeds of bio-diesel plants like
Jatropha curcas, constituting 40-50% bio-crude oil indicates its
potential as one of the most promising alternatives to conventional
sources of energy. Also, limited studies on utilization of de-oiled cake
have revealed that Jatropha bio-waste has good potential to be used as
organic fertilizers produced via aerobic and anaerobic treatment.
However, their commercial exploitation has not yet been possible. The
present study aims at developing appropriate bio-processes and
formulations utilizing Jatropha seed cake as organic fertilizer, for
improving the growth of Polianthes tuberose L. (Tuberose). Pot
experiments were carried out by growing tuberose plants on soil
treated with composted formulations of Jatropha de-oiled cake, Farm
Yard Manure (FYM) and inorganic fertilizers were also blended in
soil. The treatment was carried out through soil amendment as well as
foliar spray. The growth and morphological parameters were
monitored for entire crop cycle.
The growth Length and number of leaves, spike length, rachis
length, number of bulb per plant and earliness of sprouting of bulb and
yield enhancement were comparable to that achieved under inorganic
fertilizer. Furthermore, performance of inorganic fertilizer also showed
an improvement when blended with composted bio-waste. These
findings would open new avenues for Jatropha based bio-wastes to be
composted and used as organic fertilizers for commercial floriculture.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: Measurements of radioactivity in the environment is of great importance to monitor and control the levels of radiation to which man is exposed directly or indirectly. It is necessary to show that regardless of working or being close to nuclear power plants, people are daily in contact with some amount of radiation from the actual environment and food that are ingested, contradicting the view of most of them. The aim of this study was to analyze the rate of natural and artificial radiation from radionuclides present in cement, soil and fertilizers used in Sergipe State – Brazil. The radionuclide activitiesmeasured all samples arebelow the Brazilian limit of the exclusion and exemption criteria from the requirement of radiation protection.It was detected Be-7 in organic fertilizers that means a short interval between the brewing processes for use in agriculture. It was also detected an unexpected Cs-137 in some samples; however its activities does not represent risk for the population. Th-231 was also found in samples of soil and cement in the state of Sergipe that is an unprecedented result.
Abstract: In order to increase in chickpea quality and
agroecosystem sustainability, field experiments were carried out in
2007 and 2008 growing seasons. In this research the effects of
different organic, chemical and biological fertilizers were
investigated on grain yield and quality of chickpea. Experimental
units were arranged in split-split plots based on randomized complete
blocks with three replications. The highest amounts of yield and yield
components were obtained in G1×N5 interaction. Significant
increasing of N, P, K, Fe and Mg content in leaves and grains
emphasized on superiority of mentioned treatment because each one
of these nutrients has an approved role in chlorophyll synthesis and
photosynthesis ability of the crop. The combined application of
compost, farmyard manure and chemical phosphorus (N5) had the
best grain quality due to high protein, starch and total sugar contents,
low crude fiber and reduced cooking time.
Abstract: Vermicomposting is the conversion of organic waste
into bio-fertilizers through the action of earthworm. This technology
is widely used for organic solid waste management. Waste corn pulp
blended with cow dung manure was vermicomposted over 30 days
using Eisenia fetida earthworms species. pH, temperature, moisture
content, and electrical conductivity were daily monitored. The
feedstock, vermicompost and vermiwash were analyzed for nutrient
composition. The average temperature and moisture content in the
vermi-reactor was 22.5°C and 42.5% respectively. The vermicompost
and vermiwash had an almost neutral pH whilst the electrical
conductivity was 21% higher in the vermicompost. The nitrogen and
potassium content was 57% and 79.6% richer in the vermicompost
respectively compared to the vermiwash. However, the vermiwash
was 84% richer in phosphorous as compared to vermicompost.
Furthermore, the vermiwash was 89.1% and 97.6% richer in Ca and
Mg respectively and was 97.8% richer in Na salts compared to the
vermicompost. The vermiwash also indicated a significantly higher
amount of micronutrients. Both bio-fertilizers were rich in nutrients
specification for fertilizers.
Abstract: The storage of chemical fertilizers in concrete building often leads to durability problems due to chemical attack. The damage of concrete is mostly caused by certain ammonium salts. The main purpose of the research is to investigate the durability properties of concrete being exposed to ammonium nitrate solution. In this investigation, experiments are conducted on concrete type G50 and G60. The leaching process is achieved by the use of 20% concentration solution of ammonium nitrate. The durability properties investigated are water absorption, volume of permeable voids, and sorptivity. Compressive strength, pH value, and degradation depth are measured after a certain period of leaching. A decrease in compressive strength and an increase in porosity are found through the conducted experiments. Apart from that, the experimental data shows that pH value decreases with increased leaching time while the degradation depth of concrete increases with leaching time. By comparing concrete type G50 and G60, concrete type G60 is more resistant to ammonium nitrate attack.
Abstract: In most wheat growing moderate regions and
especially in the north of Iran climate, is affected grain filling by
several physical and abiotic stresses. In this region, grain filling often
occurs when temperatures are increasing and moisture supply is
decreasing. The experiment was designed in RCBD with split plot
arrangements with four replications. Four irrigation treatments
included (I0) no irrigation (check); (I1) one irrigation (50 mm) at
heading stage; (I2) two irrigation (100 mm) at heading and anthesis
stage; and (I3) three irrigation (150 mm) at heading, anthesis and
early grain filling growth stage, two wheat cultivars (Milan and
Shanghai) were cultured in the experiment. Totally raining was 453
mm during the growth season. The result indicated that biological
yield, grain yield and harvest index were significantly affected by
irrigation levels. I3 treatment produced more tillers number in m2,
fertile tillers number in m2, harvest index and biological yield. Milan
produced more tillers number in m2, fertile tillers in m2, while
Shanghai produced heavier tillers and grain 1000 weight. Plant height
was significant in wheat varieties while were not statistically
significant in irrigation levels. Milan produced more grain yield,
harvest index and biological yield. Grain yield shown that I1, I2, and
I3 produced increasing of 5228 (21%), 5460 (27%) and 5670 (29%)
kg ha-1, respectively. There was an interaction of irrigation and
cultivar on grain yields. In the absence of the irrigation reduced grain
1000 weight from 45 to 40 g. No irrigation reduced soil moisture
extraction during the grain filling stage. Current assimilation as a
source of carbon for grain filling depends on the light intercepting
viable green surfaces of the plant after anthesis that due to natural
senescence and the effect of various stresses. At the same time the
demand by the growing grain is increasing. It is concluded from
research work that wheat crop irrigated Milan cultivar could increase
the grain yield in comparison with Shanghai cultivar. Although, the
grain yield of Shanghai under irrigation was slightly lower than
Milan. This grain yield also was related to weather condition, sowing
date, plant density and location conditions and management of
fertilizers, because there was not significant difference in biological
and straw yield. The best result was produced by I1 treatment. I2 and
I3 treatments were not significantly difference with I1 treatment.
Grain yield of I1 indicated that wheat is under soil moisture
deficiency. Therefore, I1 irrigation was better than I0.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.
Abstract: This paper is to present context-aware sensor grid
framework for agriculture and its design challenges. Use of sensor
networks in the domain of agriculture is not new. However, due to
the unavailability of any common framework, solutions that are
developed in this domain are location, environment and problem
dependent. Keeping the need of common framework for agriculture,
Context-Aware Sensor Grid Framework is proposed. It will be
helpful in developing solutions for majority of the problems related
to irrigation, pesticides spray, use of fertilizers, regular monitoring of
plot and yield etc. due to the capability of adjusting according to
location and environment. The proposed framework is composed of
three layer architecture including context-aware application layer,
grid middleware layer and sensor network layer.
Abstract: The use of bioindicators plants (lichens, bryophytes
and Sphagnum....) in monitoring pollution by heavy metals has been
the subject of several works. However, few studies have addressed
the impact of specific type-s pollutants (fertilizers, pesticides.) on
these organisms.
We propose in this work to make the highlighting effect of NPKs
(NPK: nitrogen-phosphate-potassium-sulfate (NP2O5K2O) (15,15,15),
at concentrations of 10, 20, 30 , 40 and 50mM/L) on the activity of
detoxification enzymes (GSH/GST, CAT, APX and MDA) of plant
bioindicators (mosses and lichens) after treatment for 3 and 7 days.
This study shows the important role of the defense system in the
accumulation and tolerance to chemical pollutants through the
activation of enzymatic (GST (glutathione-S-transferase, APX
(ascorbat peroxidase), CAT (catalase)) and nonenzymatic biomarkers
(GSH (glutathione), MDA (malondialdehyde)) against oxidative
stress generated by the NPKs.
Abstract: Cameron Highlands is a mountainous area subjected
to torrential tropical showers. It extracts 5.8 million liters of water
per day for drinking supply from its rivers at several intake points.
The water quality of rivers in Cameron Highlands, however, has
deteriorated significantly due to land clearing for agriculture,
excessive usage of pesticides and fertilizers as well as construction
activities in rapidly developing urban areas. On the other hand, these
pollution sources known as non-point pollution sources are diverse
and hard to identify and therefore they are difficult to estimate.
Hence, Geographical Information Systems (GIS) was used to provide
an extensive approach to evaluate landuse and other mapping
characteristics to explain the spatial distribution of non-point sources
of contamination in Cameron Highlands. The method to assess
pollution sources has been developed by using Cameron Highlands
Master Plan (2006-2010) for integrating GIS, databases, as well as
pollution loads in the area of study. The results show highest annual
runoff is created by forest, 3.56 × 108 m3/yr followed by urban
development, 1.46 × 108 m3/yr. Furthermore, urban development
causes highest BOD load (1.31 × 106 kgBOD/yr) while agricultural
activities and forest contribute the highest annual loads for
phosphorus (6.91 × 104 kgP/yr) and nitrogen (2.50 × 105 kgN/yr),
respectively. Therefore, best management practices (BMPs) are
suggested to be applied to reduce pollution level in the area.
Abstract: In order to evaluation the effects of soil organic
matter and biofertilizer on chickpea quality and biological
nitrogen fixation, field experiments were carried out in 2007
and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on
grain yield and yield component, minerals, organic compounds
and cooking time of chickpea. Experimental units were
arranged in split-split plots based on randomized complete
blocks with three replications. Main plots consisted of (G1):
establishing a mixed vegetation of Vicia panunica and
Hordeum vulgare and (G2): control, as green manure levels.
Also, five strategies for obtaining the base fertilizer
requirement including (N1): 20 t.ha-1 farmyard manure; (N2):
10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5):
10 t.ha-1 farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1
triple super phosphate were considered in sub plots.
Furthermoree four levels of biofertilizers consisted of (B1):
Bacillus lentus + Pseudomonas putida; (B2): Trichoderma
harzianum; (B3): Bacillus lentus + Pseudomonas putida +
Trichoderma harzianum; and (B4): control (without
biofertilizers) were arranged in sub-sub plots. Results showed
that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield
were obtained in G1×N5 interaction. Comparison of all 2-way
and 3-way interactions showed that G1N5B3 was determined
as the superior treatment. Significant increasing of N, P2O5,
K2O, Fe and Mg content in leaves and grains emphasized on
superiority of mentioned treatment because each one of these
nutrients has an approved role in chlorophyll synthesis and
photosynthesis abilities of the crops. The combined application
of compost, farmyard manure and chemical phosphorus (N5)
in addition to having the highest yield, had the best grain
quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.