Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: Transportation is of great importance in the current
life of human beings. The transportation system plays many roles,
from economical development to after-catastrophe aids such as
rescue operation in the first hours and days after an earthquake. In
after earthquakes response phase, transportation system acts as a
basis for ground operations including rescue and relief operation,
food providing for victims and etc. It is obvious that partial or
complete obstruction of this system results in the stop of these
operations. Bridges are one of the most important elements of
transportation network. Failure of a bridge, in the most optimistic
case, cuts the relation between two regions and in more developed
countries, cuts the relation of numerous regions. In this paper, to
evaluate the vulnerability and estimate the damage level of Tehran
bridges, HAZUS method, developed by Federal Emergency
Management Agency (FEMA) with the aid of National Institute of
Building Science (NIBS), is used for the first time in Iran. In this
method, to evaluate the collapse probability, fragility curves are
used. Iran is located on seismic belt and thus, it is vulnerable to
earthquakes. Thus, the study of the probability of bridge collapses, as
an important part of transportation system, during earthquakes is of
great importance. The purpose of this study is to provide fragility
curves for Gisha Bridge, one of the longest steel bridges in Tehran,
as an important lifeline element. Besides, the damage probability for
this bridge during a specific earthquake, introduced as scenario
earthquakes, is calculated. The fragility curves show that for the
considered scenario, the probability of occurrence of complete
collapse for the bridge is 8.6%.
Abstract: From past many decades human beings are suffering
from plethora of natural disasters. Occurrence of disasters is a
frequent process; it changes conceptual myths as more and more
advancement are made. Although we are living in technological era
but in developing countries like Pakistan disasters are shaped by
socially constructed roles. The need is to understand the most
vulnerable group of society i.e. females; their issues are complex in
nature because of undermined gender status in the society. There is a
need to identify maximum issues regarding females and to enhance
the achievement of millennium development goals (MDGs). Gender
issues are of great concern all around the globe including Pakistan.
Here female visibility in society is low, and also during disasters, the
failure to understand the reality that concentrates on double burden
including productive and reproductive care. Women have to
contribute a lot in society so we need to make them more disaster
resilient. For this non-structural measures like awareness, trainings
and education must be carried out. In rural and in urban settings in
any disaster like earthquake or flood, elements like gender
perspective, their age, physical health, demographic issues contribute
towards vulnerability. In Pakistan the gender issues in disasters were
of less concern before 2005 earthquake and 2010 floods. Significant
achievements are made after 2010 floods when gender and child cell
was created to provide all facilities to women and girls. The aim of
the study is to highlight all necessary facilities in a disaster to build
coping mechanism in females from basic rights till advance level
including education.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper presents an analytical solution to get a reliable estimation of the hydrodynamic pressure on gravity dams induced by vertical component earthquake when solving the fluid and dam interaction problem. Presented analytical technique is presented for calculation of earthquake-induced hydrodynamic pressure in the reservoir of gravity dams allowing for water compressibility and wave absorption at the reservoir bottom. This new analytical solution can take into account the effect of bottom material on seismic response of gravity dams. It is concluded that because the vertical component of ground motion causes significant hydrodynamic forces in the horizontal direction on a vertical upstream face, responses to the vertical component of ground motion are of special importance in analysis of concrete gravity dams subjected to earthquakes.
Abstract: There is increasing evidence that earthquakes produce electromagnetic signals observable at the surface in the extremely low to very low freqency (ELF - VLF) range often in advance to the main event. These precursors are candidates for prediction purposes. Laboratory experiments con´¼ürm that material under load emits an electromagnetic signature, the detailed generation mechanisms how- ever are not well understood yet.
Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: As the world move to the accomplishment of Performance Based Engineering philosophies in seismic design of Civil Engineering structures, new seismic design provisions require Structural Engineers to perform both static and dynamic analysis for the design of structures. While Linear Equivalent Static Analysis is performed for regular buildings up to 90m height in zone I and II, Dynamic Analysis should be performed for regular and irregular buildings in zone IV and V. Dynamic Analysis can take the form of a dynamic Time History Analysis or a linear Response Spectrum Analysis. In present study, Multi-storey irregular buildings with 20 stories have been modeled using software packages ETABS and SAP 2000 v.15 for seismic zone V in India. This paper also deals with the effect of the variation of the building height on the structural response of the shear wall building. Dynamic responses of building under actual earthquakes, EL-CENTRO 1949 and CHI-CHI Taiwan 1999 have been investigated. This paper highlights the accuracy and exactness of Time History analysis in comparison with the most commonly adopted Response Spectrum Analysis and Equivalent Static Analysis.
Abstract: We study dynamic instability in high-rise steel moment
resisting frames (SMRFs) subjected to synthetic long-period ground
motions caused by hypothetical huge subduction earthquakes. Since
long duration as well as long dominant periods is a characteristic of
long-period ground motions, interstory drifts may enter the negative
postyield stiffness range many times when high-rise buildings are
subjected to long-period ground motions. Through the case studies of
9 high-rise SMRFs designed in accordance with the Japanese design
practice in 1980s, we demonstrate that drifting, or accumulation of
interstory drifts in one direction, occurs at the lower stories of the
SMRFs, if their natural periods are close to the dominant periods of the
long-period ground motions. The drifting led to residual interstory
drift ratio over 0.01, or to collapse if the design base shear was small.
Abstract: In the territories where high-intensity
earthquakes are frequent is paid attention to the solving of the
seismic problems. In the paper are described two
computational model variants based on finite element method
of the construction with different subsoil simulation (rigid or
elastic subsoil) is used. For simulation and calculations
program system based on method final elements ANSYS was
used. Seismic responses calculations of residential building
structure were effected on loading characterized by
accelerogram for comparing with the responses spectra
method.
Abstract: Because of architectural condition and structure application, sometimes mass source and stiffness source are not coincidence, and the structure is irregular. The structure is also might be asymmetric as an asymmetric bracing in plan which leads to unbalance distribution of stiffness or because of unbalance distribution of the mass. Both condition lead to eccentricity and torsion in the structure. The deficiency of ordinary code to evaluate the performance of steel structures against earthquake has been caused designing based on performance level or capacity spectrum be used. By using the mentioned methods it is possible to design a structure that its behavior against different earthquakes be predictive. In this article 5- story buildings with different percentage of asymmetric which is because of stiffness changes have been designed. The static and dynamic nonlinear analysis under three acceleration recording has been done. Finally performance level of the structure has been evaluated.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: Many studies have been conducted for derivation of
attenuation relationships worldwide, however few relationships have
been developed to use for the seismic region of Iranian plateau and
only few of these studies have been conducted for derivation of
attenuation relationships for parameters such as uniform duration.
Uniform duration is the total time during which the acceleration is
larger than a given threshold value (default is 5% of PGA). In this
study, the database was same as that used previously by Ghodrati
Amiri et al. (2007) with same correction methods for earthquake
records in Iran. However in this study, records from earthquakes with
MS< 4.0 were excluded from this database, each record has
individually filtered afterward, and therefore the dataset has been
expanded. These new set of attenuation relationships for Iran are
derived based on tectonic conditions with soil classification into rock
and soil. Earthquake parameters were chosen to be
hypocentral distance and magnitude in order to make it easier to use
the relationships for seismic hazard analysis. Tehran is the capital
city of Iran wit ha large number of important structures. In this study,
a probabilistic approach has been utilized for seismic hazard
assessment of this city. The resulting uniform duration against return
period diagrams are suggested to be used in any projects in the area.
Abstract: To increase the maximum span of cable-stayed
bridges, Uwe Starossek has developed a modified statical system.
The basic idea of this new concept is the use of pairs of inclined
pylon legs that spread out longitudinally from the foundation base or
from the girder level.
Spread-pylon cable-stayed bridge has distinct advantage like
reduction of sag of cables and oscillation of cable during earthquake
over traditional cable-stayed bridges. Spread-pylon also improves
seismic performance of deck during strong ground motion.