Abstract: In contemporary global and dynamically developing environment there is a need of the strategic planning fundamental. It is complicated, but at the same time important process from the point of view of continual keeping of competitive advantage. The aim of the paper is formulation of strategic goals for the needs of the small enterprises. There will be used Balanced Scorecard as a balanced system of the indicators for the clearing and transferring vision into particular goals. In particular perspectives the theme will be focused on strategic goals. Consequently will be mention the concept of the competitiveness IDINMOSU. This connect to Balanced Scorecard.
Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.
Abstract: Larval rearing and seed production of most of tetra fishes (Family: Characidae) is critical due to their small size larvae and limited numbers of spawning attempts. During the present study the effect of different live foods on growth and survival of neon tetra, Paracheirodon innesi larvae (length 3.1 ± 0.012mm, weight 0.048 ± 0.00015mg) and early fry (length = 6.44 ± 0.025mm, weight = 0.64 ± 0.003mg and 13 days old) was determined in two experiments. Experiment I was conducted for rearing the larvae by using mixed green water and Infusoria whereas, in Experiment II, early fry were fed with mixed zooplankton, decapsulated Artemia cyst and Artemia nauplii. The larvae fed on mixed green water showed significant (p
Abstract: This paper utilizes a finite element analysis to study
the bearing capacity of ring footings on a two-layered soil. The upper
layer, that the footing is placed on it, is soft clay and the underneath
layer is a cohesionless sand. For modeling soils, Mohr–Coulomb
plastic yield criterion is employed. The effects of two factors, the
clay layer thickness and the ratio of internal radius of the ring footing
to external radius of the ring, have been analyzed. It is found that the
bearing capacity decreases as the value of ri / ro increases.
Although, as the clay layer thickness increases the bearing capacity
was alleviated gradually.
Abstract: The aim of the study was to identify seat belt wearing
factor among road users in Malaysia. Evidence-based approach
through in-depth crash investigation was utilised to determine the
intended objectives. The objective was scoped into crashes
investigated by Malaysian Institute of Road Safety Research
(MIROS) involving passenger vehicles within 2007 and 2010. Crash
information of a total of 99 crash cases involving 240 vehicles and
864 occupants were obtained during the study period. Statistical test
and logistic regression analysis have been performed. Results of the
analysis revealed that gender, seat position and age were associated
with seat belt wearing compliance in Malaysia. Males are 97.6%
more likely to wear seat belt compared to females (95% CI 1.317 to
2.964). By seat position, the finding indicates that frontal occupants
were 82 times more likely to be wearing seat belt (95% CI 30.199 to
225.342) as compared to rear occupants. It is also important to note
that the odds of seat belt wearing increased by about 2.64% (95% CI
1.0176 to 1.0353) for every one year increase in age. This study is
essential in understanding the Malaysian tendency in belting up
while being occupied in a vehicle. The factors highlighted in this
study should be emphasized in road safety education in order to
increase seat belt wearing rate in this country and ultimately in
preventing deaths due to road crashes.
Abstract: Wireless mobile communications have experienced
the phenomenal growth through last decades. The advances in
wireless mobile technologies have brought about a demand for high
quality multimedia applications and services. For such applications
and services to work, signaling protocol is required for establishing,
maintaining and tearing down multimedia sessions. The Session
Initiation Protocol (SIP) is an application layer signaling protocols,
based on request/response transaction model. This paper considers
SIP INVITE transaction over an unreliable medium, since it has been
recently modified in Request for Comments (RFC) 6026. In order to
help in assuring that the functional correctness of this modification is
achieved, the SIP INVITE transaction is modeled and analyzed using
Colored Petri Nets (CPNs). Based on the model analysis, it is
concluded that the SIP INVITE transaction is free of livelocks and
dead codes, and in the same time it has both desirable and
undesirable deadlocks. Therefore, SIP INVITE transaction should be
subjected for additional updates in order to eliminate undesirable
deadlocks. In order to reduce the cost of implementation and
maintenance of SIP, additional remodeling of the SIP INVITE
transaction is recommended.
Abstract: The effect of the rotational speed and axial torque on
the diagnostics of tapered rolling element bearing defects was
investigated. The accelerometer was mounted on the bearing housing
and connected to Sound and Vibration Analyzer (SVAN 958) and
was used to measure the accelerations from the bearing housing. The
data obtained from the bearing was processed to detect damage of the
bearing using statistical tools and the results were subsequently
analyzed to see if bearing damage had been captured. From this study
it can be seen that damage is more evident when the bearing is
loaded. Also, at the incipient stage of damage the crest factor and
kurtosis values are high but as time progresses the crest factors and
kurtosis values decrease whereas the peak and RMS values are low at
the incipient stage but increase with damage.
Abstract: In order to study pressed pile test and ultimate bearing
capacity character of large-diameter steel pipe pile, based on two high-piled wharfs of Zhanjiang Port, pressed pile test and numerical simulation of three large-diameter steel pipe piles are analyzed in this
paper. Anchored pile method is used to pressed pile test, and the
curves of Q-s and ultimate bearing capacity are attained. Then the three piles are numerically simulated by ABAQUS, and results of numerical simulation and those of field test are comparatively analyzed. The results show that settlement value of numerical
simulation is larger than that of field test in the process of loading, the difference value is widening with the increasing of load, and the
ultimate difference value of settlement is 20% to 30%.
Abstract: Cameron Highlands is a mountainous area subjected
to torrential tropical showers. It extracts 5.8 million liters of water
per day for drinking supply from its rivers at several intake points.
The water quality of rivers in Cameron Highlands, however, has
deteriorated significantly due to land clearing for agriculture,
excessive usage of pesticides and fertilizers as well as construction
activities in rapidly developing urban areas. On the other hand, these
pollution sources known as non-point pollution sources are diverse
and hard to identify and therefore they are difficult to estimate.
Hence, Geographical Information Systems (GIS) was used to provide
an extensive approach to evaluate landuse and other mapping
characteristics to explain the spatial distribution of non-point sources
of contamination in Cameron Highlands. The method to assess
pollution sources has been developed by using Cameron Highlands
Master Plan (2006-2010) for integrating GIS, databases, as well as
pollution loads in the area of study. The results show highest annual
runoff is created by forest, 3.56 × 108 m3/yr followed by urban
development, 1.46 × 108 m3/yr. Furthermore, urban development
causes highest BOD load (1.31 × 106 kgBOD/yr) while agricultural
activities and forest contribute the highest annual loads for
phosphorus (6.91 × 104 kgP/yr) and nitrogen (2.50 × 105 kgN/yr),
respectively. Therefore, best management practices (BMPs) are
suggested to be applied to reduce pollution level in the area.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: The damage tolerance behavior of integrally and
conventional stiffened panel is investigated based on the fracture
mechanics and finite element analysis. The load bearing capability
and crack growth characteristic of both types of the stiffened panels
having same configuration subjected to distributed tensile load is
examined in this paper. A fourteen-stringer stiffened panel is
analyzed for a central skin crack propagating towards the adjacent
stringers. Stress intensity factors and fatigue crack propagation rates
of both types of the stiffened panels are then compared. The analysis
results show that integral stiffening causes higher stress intensity
factor than conventional stiffened panel as the crack tip passes
through the stringer and the integrally stiffened panel has less load
bearing capability than the riveted stiffened panel.
Abstract: Recently, the advanced technologies that offer high
precision product, relative easy, economical process and also rapid
production are needed to realize the high demand of ultra precision
micro part. In our research, micromanufacturing based on soft
lithography and nanopowder injection molding was investigated. The
silicone metal pattern with ultra thick and high aspect ratio succeeds to
fabricate Polydimethylsiloxane (PDMS) micro mold. The process
followed by nanopowder injection molding (PIM) by a simple vacuum
hot press. The 17-4ph nanopowder with diameter of 100 nm, succeed
to be injected and it forms green sample microbearing with thickness,
microchannel and aspect ratio is 700μm, 60μm and 12, respectively.
Sintering process was done in 1200 C for 2 hours and heating rate
0.83oC/min. Since low powder load (45% PL) was applied to achieve
green sample fabrication, ~15% shrinkage happen in the 86% relative
density. Several improvements should be done to produce high
accuracy and full density sintered part.
Abstract: In this paper is study the possibility of successfully
implementing of hollow roller concept in order to minimize inertial
mass of the large bearings, with major results in diminution of the
material consumption, increasing of power efficiency (in wind power
station area), increasing of the durability and life duration of the large
bearings systems, noise reduction in working, resistance to
vibrations, an important diminution of losses by abrasion and
reduction of the working temperature. In this purpose was developed
an original solution through which are reduced mass, inertial forces
and moments of large bearings by using of hollow rollers. The
research was made by using the method of finite element analysis
applied on software type Solidworks - Nastran. Also, is study the
possibility of rapidly changing the manufacturing system of solid and
hollow cylindrical rollers.
Abstract: Dynamic characteristics of a four-lobe journal bearing
of micropolar fluids are presented. Lubricating oil containing
additives and contaminants is modelled as micropolar fluid. The
modified Reynolds equation is obtained using the micropolar
lubrication theory and solving it by using finite difference technique.
The dynamic characteristics in terms of stiffness, damping
coefficients, the critical mass and whirl ratio are determined for
various values of size of material characteristic length and the
coupling number. The results show compared with Newtonian fluids,
that micropolar fluid exhibits better stability.
Abstract: A four-lobe pressure dam bearing which is
produced by cutting two pressure dams on the upper two lobes and
two relief-tracks on the lower two lobes of an ordinary four-lobe
bearing is found to be more stable than a conventional four-lobe
bearing. In this paper a four-lobe pressure dam bearing supporting
rigid and flexible rotors is analytically investigated to determine its
performance when L/D ratio is varied in the range 0.75 to 1.5. The
static and dynamic characteristics are studied at various L/D ratios.
The results show that the stability of a four-lobe pressure dam
bearing increases with decrease in L/D ratios both for rigid as well as
flexible rotors.