Abstract: The primary objective of this research is to improve the flexural capacity of FRP strengthened RC Beam structures with Aluminum and Titanium laminates. FRP rupture of flexural strengthened RC beams using FRP plates generally occurs at the interface between FRP plate and the beam. Therefore, in order to prevent brittle rupture and improve the ductility of the system, this research was performed by using Aluminum and Titanium materials between the two different structural systems. The research also aims to provide various strengthening/retrofitting methods for RC beam structures and to conduct a preliminary analysis of the demands on the structural systems. This was achieved by estimation using the experimental data from this research to identify a flexural capacity for the systems. Ultimately, the preliminary analysis of current study showed that the flexural capacity and system demand ductility was significantly improved by the systems inserted with Aluminum and Titanium anchor plates. Further verification of the experimental research is currently on its way to develop a new or reliable design guideline to retrofit/strengthen the concrete-FRP structural system can be evaluated.
Abstract: Manganese steel (Hadfield) is one of the important
alloys in industry due to its special properties. High work hardening
ability with appropriate toughness and ductility are the properties that
caused this alloy to be used in wear resistance parts and in high
strength condition. Heat treatment is the main process through which
the desired mechanical properties and microstructures are obtained in
Hadfield steel. In this study various heat treatment cycles, differing in
austenising temperature, time and quenching solution are applied. For
this purpose, the same samples of manganese steel was heat treated in
9 different cycles, and then the mechanical properties and
microstructures were investigated. Based on the results of the study,
the optimum heat treatment cycle was obtained.
Abstract: The present work presents a method of calculating the
ductility of rectangular sections of beams considering nonlinear
behavior of concrete and steel. This calculation procedure allows us
to trace the curvature of the section according to the bending
moment, and consequently deduce ductility. It also allowed us to
study the various parameters that affect the value of the ductility. A
comparison of the effect of maximum rates of tension steel, adopted
by the codes, ACI [1], EC8 [2] and RPA [3] on the value of the
ductility was made. It was concluded that the maximum rate of steels
permitted by the ACI [1] codes and RPA [3] are almost similar in
their effect on the ductility and too high. Therefore, the ductility
mobilized in case of an earthquake is low, the inverse of code EC8
[2]. Recommendations have been made in this direction.
Abstract: Aluminum alloy has an extensive range of industrial application due to its consistent mechanical properties and structural integrity. The heat treatment by precipitation technique affected the Magnesium, Silicon Manganese and copper crystals dissolved in the Aluminum alloy. The crystals dislocated to precipitate on the crystal’s boundaries of the Aluminum alloy when given a thermal energy increased its hardness. In this project various times and temperature were varied to find out the best combination of these variables to increase the precipitation of the metals on the Aluminum crystal’s boundaries which will lead to get the highest hardness. These specimens are then tested for their hardness and tensile strength. It is noticed that when the temperature increases, the precipitation increases and consequently the hardness increases. A threshold temperature value (264C0) of Aluminum alloy should not be reached due to the occurrence of recrystalization which causes the crystal to grow. This recrystalization process affected the ductility of the alloy and decrease hardness. In addition, and while increasing the temperature the alloy’s mechanical properties will decrease. The mechanical properties, namely tensile and hardness properties are investigated according to standard procedures. In this research, different temperature and time have been applied to increase hardening.The highest hardness at 100°c in 6 hours equals to 207.31 HBR, while at the same temperature and time the lowest elongation equals to 146.5.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: An effect of rolling temperature on the mechanical properties and microstructural evolution of an Al-Mg-Si alloy was studied. The material was rolled up to a true strain of ~0.7 at three different temperatures viz; room temperature, liquid propanol and liquid nitrogen. The liquid nitrogen rolled sample exhibited superior properties with a yield and tensile strength of 332 MPa and 364 MPa, respectively, with a reasonably good ductility of ~9%. The liquid nitrogen rolled sample showed around 54 MPa increase in tensile strength without much reduction in the ductility as compared to the as received T6 condition alloy. The microstructural details revealed equiaxed grains in the annealed and solutionized sample and elongated grains in the rolled samples. In addition, the cryorolled samples exhibited fine grain structure compared to the room temperature rolled samples.
Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: With the development of the Polyvinyl chloride
(PVC) products in many applications, the challenge of investigating
the raw material composition and reducing the cost have both
become more and more important. Considerable research has been
done investigating the effect of additives on the PVC products. Most
of the PVC composites research investigates only the effect of
single/few factors, at a time. This isolated consideration of the input
factors does not take in consideration the interaction effect of the
different factors. This paper implements a mixture experimental
design approach to find out a cost-effective PVC composition for the
production of electrical-insulation cables considering the ASTM
Designation (D) 6096. The results analysis showed that a minimum
cost can be achieved through using 20% virgin PVC, 18.75%
recycled PVC, 43.75% CaCO3 with participle size 10 microns, 14%
DOP plasticizer, and 3.5% CPW plasticizer. For maximum UTS the
compound should consist of: 17.5% DOP, 62.5% virgin PVC, and
20.0% CaCO3 of particle size 5 microns. Finally, for the highest
ductility the compound should be made of 35% virgin PVC, 20%
CaCO3 of particle size 5 microns, and 45.0% DOP plasticizer.
Abstract: This paper in essence presents comparative
experimental data on the mechanical performance of steel and
synthetic fibre-reinforced concrete under compression, tensile split
and flexure. URW1050 steel fibre and HPP45 synthetic fibre, both
with the same concrete design mix, have been used to make cube
specimens for a compression test, cylinders for a tensile split test and
beam specimens for a flexural test. The experimental data
demonstrated steel fibre reinforced concrete to be stronger in flexure
at early stages, whilst both fibre reinforced concrete types displayed
comparatively the same performance in compression, tensile splitting
and 28-day flexural strength. In terms of post-crack controlHPP45
was preferable.
Abstract: High strength concrete (HSC) provides high strength
but lower ductility than normal strength concrete. This low ductility
limits the benefit of using HSC in building safe structures. On the
other hand, when designing reinforced concrete beams, designers
have to limit the amount of tensile reinforcement to prevent the
brittle failure of concrete. Therefore the full potential of the use of
steel reinforcement can not be achieved. This paper presents the idea
of confining concrete in the compression zone so that the HSC will
be in a state of triaxial compression, which leads to improvements in
strength and ductility. Five beams made of HSC were cast and tested.
The cross section of the beams was 200×300 mm, with a length of 4
m and a clear span of 3.6 m subjected to four-point loading, with
emphasis placed on the midspan deflection. The first beam served as
a reference beam. The remaining beams had different tensile
reinforcement and the confinement shapes were changed to gauge
their effectiveness in improving the strength and ductility of the
beams. The compressive strength of the concrete was 85 MPa and the
tensile strength of the steel was 500 MPa and for the stirrups and
helixes was 250 MPa. Results of testing the five beams proved that
placing helixes with different diameters as a variable parameter in the
compression zone of reinforced concrete beams improve their
strength and ductility.
Abstract: In the present work, a comparative study on the
microstructure and mechanical properties of as cast, cast aged and
forged aged A356 alloy has been investigated. The study reveals that
mechanical properties of A356 alloy are highly influenced by melt
treatment and solid state processing. Cast aged alloys achieve highest
strength and hardness compared to as cast and forge aged ones. Ones
treated with combined addition of grain refiners and modifiers
achieve maximum strength and hardness. Cast aged A356 alloy
possesses higher wear resistance compared to as cast and forge aged
ones. Forging improves both strength and ductility of alloys over as
cast ones. However, the improvement in ductility is perceptible only
for properly grain refined and modified alloys. Ones refined with
0.65% Al-3Ti shows highest improvement in ductility while ones
treated with 0.20% Al-10Sr exhibits less improvement in ductility.
Abstract: Experimental study on the influence of fibre content
on crack behaviour and propagation in synthetic-fibre reinforced
beams has been reported in this paper. The tensile behaviour of
metallic fibre concrete is evaluated in terms of residual flexural
tensile strength values determined from the load-crack mouth
opening displacement curve or load-deflection curve obtained by
applying a centre-point load on a simply supported notched prism.
The results achieved demonstrate that an increase in fibre content has
an almost negligible effect on compressive and tensile splitting
properties, causes a marginal increment in flexural tensile strength
and increasesthe Re3 value.