Abstract: A nonlinear model of the mathematical fluid dynamics which describes the motion of an incompressible viscous rotating fluid in a homogeneous gravitational field is considered. The model is a generalization of the known Navier-Stokes system with the addition of the Coriolis parameter and the equations for changeable density. An explicit algorithm for the solution is constructed, and the proof of the existence and uniqueness theorems for the strong solution of the nonlinear problem is given. For the linear case, the localization and the structure of the spectrum of inner waves are also investigated.
Abstract: This paper illustrates the study of three isolated zero
voltage switched (ZVS) PWM full bridge (FB) converters to charge
the high voltage battery in the charger of electric vehicle (EV).
EV battery chargers have several challenges such as high efficiency,
high reliability, low cost, isolation, and high power density. The
cost of magnetic and filter components in the battery charger is
reduced when switching frequency is increased. The increase in the
switching frequency increases switching losses. ZVS is used to reduce
switching losses and to operate the converter in the battery charger
at high frequency. The performance of each of the three converters
is evaluated on the basis of ZVS range, dead times of the switches,
conduction losses of switches, circulating current stress, circulating
energy, duty cycle loss, and efficiency. The limitations and merits of
each PWM FB converter are reviewed. The converter with broader
ZVS range, high efficiency and low switch stresses is selected for
battery charger applications in EV.
Abstract: The total mass attenuation coefficients m/r, of some halides such as, NaCl, KCl, CuCl, NaBr, KBr, RbCl, AgCl, NaI, KI, AgBr, CsI, HgCl2, CdI2 and HgI2 were determined at photon energies 279.2, 320.07, 514.0, 661.6, 1115.5, 1173.2 and 1332.5 keV in a well-collimated narrow beam good geometry set-up using a high resolution, hyper pure germanium detector. The mass attenuation coefficients and the effective atomic cross sections are found to be in good agreement with the XCOM values. From these mass attenuation coefficients, the effective atomic cross sections sa, of the compounds were determined. These effective atomic cross section sa data so obtained are then used to compute the effective atomic numbers Zeff. For this, the interpolation of total attenuation cross-sections of photons of energy E in elements of atomic number Z was performed by using the logarithmic regression analysis of the data measured by the authors and reported earlier for the above said energies along with XCOM data for standard energies. The best-fit coefficients in the photon energy range of 250 to 350 keV, 350 to 500 keV, 500 to 700 keV, 700 to 1000 keV and 1000 to 1500 keV by a piecewise interpolation method were then used to find the Zeff of the compounds with respect to the effective atomic cross section sa from the relation obtained by piece wise interpolation method. Using these Zeff values, the electron densities Nel of halides were also determined. The present Zeff and Nel values of halides are found to be in good agreement with the values calculated from XCOM data and other available published values.
Abstract: Seismic inversion is a technique which has been in use for years and its main goal is to estimate and to model physical characteristics of rocks and fluids. Generally, it is a combination of seismic and well-log data. Seismic inversion can be carried out through different methods; we have conducted and compared post-stack and pre- stack seismic inversion methods on real data in one of the fields in the Persian Gulf. Pre-stack seismic inversion can transform seismic data to rock physics such as P-impedance, S-impedance and density. While post- stack seismic inversion can just estimate P-impedance. Then these parameters can be used in reservoir identification. Based on the results of inverting seismic data, a gas reservoir was detected in one of Hydrocarbon oil fields in south of Iran (Persian Gulf). By comparing post stack and pre-stack seismic inversion it can be concluded that the pre-stack seismic inversion provides a more reliable and detailed information for identification and prediction of hydrocarbon reservoirs.
Abstract: Polymer-particle interactions can be effectively utilized to produce composites that possess physicochemical properties superior to that of neat polymer. The incorporation of fillers with dimensions comparable to polymer chain size produces composites with extra-ordinary properties owing to very high surface to volume ratio. The dispersion of nanoparticles is achieved by inducing steric repulsion realized by grafting particles with polymeric chains. A comprehensive understanding of the interparticle interaction between these functionalized nanoparticles plays an important role in the synthesis of a stable polymer nanocomposite. With the focus on incorporation of clay sheets in a polymer matrix, we theoretically construct the polymer mediated interparticle potential for two nanosheets grafted with polymeric chains. The self-consistent field theory (SCFT) is employed to obtain the inhomogeneous composition field under equilibrium. Unlike the continuum models, SCFT is built from the microscopic description taking in to account the molecular interactions contributed by both intra- and inter-chain potentials. We present the results of SCFT calculations of the interaction potential curve for two grafted nanosheets immersed in the matrix of polymeric chains of dissimilar chemistry to that of the grafted chains. The interaction potential is repulsive at short separation and shows depletion attraction for moderate separations induced by high grafting density. It is found that the strength of attraction well can be tuned by altering the compatibility between the grafted and the mobile chains. Further, we construct the interaction potential between two nanosheets grafted with diblock copolymers with one of the blocks being chemically identical to the free polymeric chains. The interplay between the enthalpic interaction between the dissimilar species and the entropy of the free chains gives rise to a rich behavior in interaction potential curve obtained for two separate cases of free chains being chemically similar to either the grafted block or the free block of the grafted diblock chains.
Abstract: Natural preservatives have been used as alternatives to traditional chemical preservatives; however, a limited number have been commercially developed and many remain to be investigated as sources of safer and effective antimicrobials. In this study, we have been investigating the antimicrobial activity of an extract of Glycyrrhiza glabra (liquorice) that was provided as a waste material from the production of liquorice flavourings for the food industry, and to investigate if this retained the expected antimicrobial activity so it could be used as a natural preservative. Antibacterial activity of liquorice extract was screened for evidence of growth inhibition against eight species of Gram-negative and Gram-positive bacteria, including Listeria monocytogenes, Listeria innocua, Staphylococcus aureus, Enterococcus faecalis and Bacillus subtilis. The Gram-negative bacteria tested include Pseudomonas aeruginosa, Escherichia coli and Salmonella typhimurium but none of these were affected by the extract. In contrast, for all of the Gram-positive bacteria tested, growth was inhibited as monitored using optical density. However parallel studies using viable count indicated that the cells were not killed meaning that the extract was bacteriostatic rather than bacteriocidal. The Minimum Inhibitory Concentration [MIC] and Minimum Bactericidal Concentration [MBC] of the extract was also determined and a concentration of 50 µg ml-1 was found to have a strong bacteriostatic effect on Gram-positive bacteria. Microscopic analysis indicated that there were changes in cell shape suggesting the cell wall was affected. In addition, the use of a reporter strain of Listeria transformed with the bioluminescence genes luxABCDE indicated that cell energy levels were reduced when treated with either 12.5 or 50 µg ml-1 of the extract, with the reduction in light output being proportional to the concentration of the extract used. Together these results suggest that the extract is inhibiting the growth of Gram-positive bacteria only by damaging the cell wall and/or membrane.
Abstract: In population dynamics the study of both, the
abundance and the spatial distribution of the populations in a
given habitat, is a fundamental issue a From ecological point of
view, the determination of the factors influencing such changes
involves important problems. In this paper a mathematical model to
describe the temporal dynamic and the spatiotemporal dynamic of the
interaction of three populations (pollinators, plants and herbivores) is
presented. The study we present is carried out by stages: 1. The
temporal dynamics and 2. The spatio-temporal dynamics. In turn,
each of these stages is developed by considering three cases which
correspond to the dynamics of each type of interaction. For instance,
for stage 1, we consider three ODE nonlinear systems describing
the pollinator-plant, plant-herbivore and plant-pollinator-herbivore,
interactions, respectively. In each of these systems different types of
dynamical behaviors are reported. Namely, transcritical and pitchfork
bifurcations, existence of a limit cycle, existence of a heteroclinic
orbit, etc. For the spatiotemporal dynamics of the two mathematical
models a novel factor are introduced. This consists in considering
that both, the pollinators and the herbivores, move towards those
places of the habitat where the plant population density is high.
In mathematical terms, this means that the diffusive part of the
pollinators and herbivores equations depend on the plant population
density. The analysis of this part is presented by considering pairs of
populations, i. e., the pollinator-plant and plant-herbivore interactions
and at the end the two mathematical model is presented, these models
consist of two coupled nonlinear partial differential equations of
reaction-diffusion type. These are defined on a rectangular domain
with the homogeneous Neumann boundary conditions. We focused
in the role played by the density dependent diffusion term into
the coexistence of the populations. For both, the temporal and
spatio-temporal dynamics, a several of numerical simulations are
included.
Abstract: The paper presents and energy management strategy for a Fuel Cell, Ultracapacitor, Battery hybrid energy storage. The fuel cell hybrid power system is devised basically for emergency power requirements and transient load applications. The power density of an Ultracapacitor is extremely high and for a battery, it is subtle. For a fuel cell, the value of power density is medium. The energy density of these three stockpiling gadgets is contrarily about the power density, i.e. for the batteries it is most noteworthy and for the Ultracapacitor, it is least. Again the fuel cell has medium energy density. The proposed Energy Management System (EMS) is trying to rationalize these parameters viz. the energy density and power density. The working of the fuel cell, Ultracapacitor and batteries are controlled in a coordinated environment in a way to optimize the energy usage and at the same time to get benefits of power and energy density from their inherent characteristics. MATLAB/ Simulink® based test bench is created by using different DC-DC converters for all energy storage devices and an inverter is modeled to supply the time varying load. The results provided by the EMS are highly satisfactory that proves its adaptability.
Abstract: Biological processes based on oxidation of sulfur
compounds by chemolithotrophic microorganisms are emerging as an
efficient and eco-friendly technique for removal of sulfur from the
coal. In the present article, study was carried out to investigate the
potential of biodesulfurization process in removing the sulfur from
lignite coal sample collected from a Mongolian coal mine. The batch
biodesulfurization experiments were conducted in 2.5 L borosilicate
baffle type reactors at 35 ºC using Acidithiobacillus ferrooxidans.
The effect of pulp density on efficiency of biodesulfurization was
investigated at different solids concentration (1-10%) of coal. The
results of the present study suggested that the rate of desulfurization
was retarded at higher coal pulp density. The optimum pulp density
found 5% at which about 48% of the total sulfur was removed from
the coal.
Abstract: Concrete as a construction material is versatile because it displays high degree of fire-resistance. Concrete’s inherent ability to combat one of the most devastating disaster that a structure can endure in its lifetime, can be attributed to its constituent materials which make it inert and have relatively poor thermal conductivity. However, concrete structures must be designed for fire effects. Structural components should be able to withstand dead and live loads without undergoing collapse. The properties of high-strength concrete must be weighed against concerns about its fire resistance and susceptibility to spalling at elevated temperatures. In this paper, the causes, effects and some remedy of deterioration in concrete due to fire hazard will be discussed. Some cost effective solutions to produce a fire resistant concrete will be conversed through this paper.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.
Abstract: This paper reports the viability of developing Zn-27Al
alloy matrix hybrid composites reinforced with alumina, graphite and
fly ash (solid waste bye product of coal in thermal power plants).
This research work was aimed at developing low cost-high
performance Zn-27Al matrix composite with low density. Alumina
particulates (Al2O3), graphite added with 0, 2, 3, 4 and 5 wt% fly ash
were utilized to prepare 10wt% reinforcing phase with Zn-27Al alloy
as matrix using two-step stir casting method. Density measurement,
estimated percentage porosity, tensile testing, micro hardness
measurement and optical microscopy were used to assess the
performance of the composites produced. The results show that the
hardness, ultimate tensile strength, and percent elongation of the
hybrid composites decrease with increase in fly ash content. The
maximum decrease in hardness and ultimate tensile strength of
13.72% and 15.25% respectively were observed for composite grade
containing 5wt% fly ash. The percentage elongation of composite
sample without fly ash is 8.9% which is comparable with that of the
sample containing 2wt% fly ash with percentage elongation of 8.8%.
The fracture toughness of the fly ash containing composites was
however superior to those of composites without fly ash with 5wt%
fly ash containing composite exhibiting the highest fracture
toughness. The results show that fly ash can be utilized as
complementary reinforcement in ZA-27 alloy matrix composite to
reduce cost.
Abstract: One of the major problems being faced by human society is that the global temperature is believed to be rising due to human activity that releases carbon IV Oxide (CO2) to the atmosphere. Carbon IV Oxide is the most important greenhouse gas influencing global warming and possible climate change. With climate change becoming alarming, reducing CO2 in our atmosphere has become a primary goal of international efforts. Forest lands are major sink and could absorb large quantities of carbon if the trees are judiciously managed. The study aims at estimating the carbon sequestration capacity of Pinus caribaea (pine) and Tectona grandis (Teak) under the prevailing environmental conditions and exploring tree growth variables that influences the carbon sequestration capacity in Omo Forest Reserve, Ogun State, Nigeria. Improving forest management by manipulating growth characteristics that influences carbon sequestration could be an adaptive strategy of forestry to climate change. Random sampling was used to select Temporary Sample Plots (TSPs) in the study area from where complete enumeration of growth variables was carried out within the plots. The data collected were subjected to descriptive and correlational analyses. The results showed that average carbon stored by Pine and Teak are 994.4±188.3 Kg and 1350.7±180.6 Kg respectively. The difference in carbon stored in the species is significant enough to consider choice of species relevant in climate change adaptation strategy. Tree growth variables influence the capacity of the tree to sequester carbon. Height, diameter, volume, wood density and age are positively correlated to carbon sequestration. These tree growth variables could be manipulated by the forest manager as an adaptive strategy for climate change while plantations of high wood density species could be relevant for management strategy to increase carbon storage.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: A flow column has been innovatively used in the
design of a new electrocoagulation reactor (ECR1) that will reduce
the temperature of water being treated; where the flow columns work
as a radiator for the water being treated. In order to investigate the
performance of ECR1 and compare it to that of traditional reactors;
600 mL water samples with an initial temperature of 350C were
pumped continuously through these reactors for 30 min at current
density of 1 mA/cm2. The temperature of water being treated was
measured at 5 minutes intervals over a 30 minutes period using a
thermometer. Additional experiments were commenced to investigate
the effects of initial temperature (15-350C), water conductivity (0.15
– 1.2 S) and current density (0.5 -3 mA/cm2) on the performance of
ECR1.
The results obtained demonstrated that the ECR1, at a current
density of 1 mA/cm2 and continuous flow model, reduced water
temperature from 350C to the vicinity of 280C during the first 15
minutes and kept the same level till the end of the treatment time.
While, the temperature increased from 28.1 to 29.80C and from 29.8
to 31.90C in the batch and the traditional continuous flow models
respectively. In term of initial temperature, ECR1 maintained the
temperature of water being treated within the range of 22 to 280C
without the need for external cooling system even when the initial
temperatures varied over a wide range (15 to 350C). The influent
water conductivity was found to be a significant variable that affect
the temperature. The desirable value of water conductivity is 0.6 S.
However, it was found that the water temperature increased rapidly
with a higher current density.
Abstract: The purpose of this study is the discrimination of 28
postmenopausal with osteoporotic femoral fractures from an agematched
control group of 28 women using texture analysis based on
fractals. Two pre-processing approaches are applied on radiographic
images; these techniques are compared to highlight the choice of the
pre-processing method. Furthermore, the values of the fractal
dimension are compared to those of the fractal signature in terms of
the classification of the two populations. In a second analysis, the
BMD measure at proximal femur was compared to the fractal
analysis, the latter, which is a non-invasive technique, allowed a
better discrimination; the results confirm that the fractal analysis of
texture on calcaneus radiographs is able to discriminate osteoporotic
patients with femoral fracture from controls. This discrimination was
efficient compared to that obtained by BMD alone. It was also
present in comparing subgroups with overlapping values of BMD.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.