Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of spherical cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of spherical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter (K), magnetic parameter (m) and elasticoviscosity
parameter (β), which depends on the Non-Newtonian
coefficient. The flow parameters are found to be identical with that of
Newtonian case as elastic-viscosity parameter and magnetic
parameter tends to zero and porosity tends to infinity. It is seen that
the effect of elastico-viscosity parameter, porosity parameter and
magnetic parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of ellipsoidal cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
ellipsoidal cross section by taking into account of the porosity factor
of the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter and
the porosity parameter of the bounding surface has significant effect
on the velocity parameter.
Abstract: Artificial intelligence applications are commonly used
in industry in many fields in parallel with the developments in the
computer technology. In this study, a fire room was prepared for the
resistance of wooden construction elements and with the mechanism
here, the experiments of polished materials were carried out. By
utilizing from the experimental data, an artificial neural network
(ANN) was modelled in order to evaluate the final cross sections of
the wooden samples remaining from the fire. In modelling,
experimental data obtained from the fire room were used. In the
developed system, the first weight of samples (ws-gr), preliminary
cross-section (pcs-mm2), fire time (ft-minute), and fire temperature
(t-oC) as input parameters and final cross-section (fcs-mm2) as output
parameter were taken. When the results obtained from ANN and
experimental data are compared after making statistical analyses, the
data of two groups are determined to be coherent and seen to have no
meaning difference between them. As a result, it is seen that ANN
can be safely used in determining cross sections of wooden materials
after fire and it prevents many disadvantages.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of spherical cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
spherical cross section by taking into account of the porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter,
porosity parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: We study the anomalous WWγ and WWZ couplings by
calculating total cross sections of two processes at the LHeC with
electron beam energy Ee=140 GeV and the proton beam energy Ep=7
TeV, and at the FCC-ep collider with the polarized electron beam
energy Ee=80 GeV and the proton beam energy Ep=50 TeV. At the
LHeC with electron beam polarization, we obtain the results for the
difference of upper and lower bounds as (0.975, 0.118) and (0.285,
0.009) for the anomalous (Δκγ, λγ) and (Δκz, λz) couplings,
respectively. As for FCC-ep collider, these bounds are obtained as
(1.101, 0.065) and (0.320, 0.002) at an integrated luminosity of
Lint=100 fb^-1.
Abstract: Exact solution of an unsteady flow of elastico-viscous
electrically conducting fluid through a porous media in a tube of
elliptical cross section under the influence of constant pressure
gradient and magnetic field has been obtained in this paper. Initially,
the flow is generated by a constant pressure gradient. After attaining
the steady state, the pressure gradient is suddenly withdrawn and the
resulting fluid motion in a tube of elliptical cross section by taking
into account of the transverse magnetic field and porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K), magnetic parameter (m) and
elastico-viscosity parameter (β), which depends on the Non-
Newtonian coefficient. The flow parameters are found to be identical
with that of Newtonian case as elastic-viscosity parameter and
magnetic parameter tends to zero and porosity tends to infinity. It is
seen that the effect of elastico-viscosity parameter, magnetic
parameter and the porosity parameter of the bounding surface has
significant effect on the velocity parameter.
Abstract: Aerated concrete is a load bearing construction
material, which has high heat insulation parameters. Walls can be
erected from aerated concrete masonry constructions and in perfect
circumstances additional heat insulation is not required. The most
common problem in aerated concrete heat insulation properties is the
humidity distribution throughout the cross section of the masonry
elements as well as proper and conducted drying process of the
aerated concrete construction because only dry aerated concrete
masonry constructions can reach high heat insulation parameters.
In order to monitor drying process of the masonry and detect
humidity distribution throughout the cross section of aerated concrete
masonry construction application of electrical impedance
spectrometry is applied. Further test results and methodology of this
non-destructive testing method is described in this paper.
Abstract: Floods play a key role in landform evolution of an
area. This process is likely to alter the topography of the earth’s
surface. The present study area, Kota Bharu is very prone to floods
extends from upstream of Kelantan River near Kemubu to the
downstream area near Kuala Besar. These flood events which occur
every year in the study area exhibit a strong bearing on river
morphological set-up. In the present study, three satellite imageries of
different time periods have been used to manifest the post-flood
landform changes. The pre-processing of the images such as subset,
geometric corrections and atmospheric corrections were carried-out
using ENVI 4.5 followed by the analysis processes. Twenty sets of
cross sections were plotted using software Erdas 9.2, ERDAS and
ArcGis 10 for the all three images. The results show a significant
change in the length of the cross section which suggest that the
geomorphological processes play a key role in carving and shaping
the river banks during the floods.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: The article presents the concept of an electromagnetic
circuit generator with permanent magnets mounted on the surface
rotor core designed for single phase work. Computation field-circuit
model was shown. The spectrum of time course of voltages in the
idle work was presented. The cross section with graphically
presentation of magnetic induction in particular parts of
electromagnetic circuits was presented. Distribution of magnetic
induction at the rated load point for each phase was shown. The time
course of voltages and currents for each phases for rated power were
displayed. An analysis of laboratory results and measurement of load
characteristics of the generator was discussed. The work deals with
three electromagnetic circuits of generators with permanent magnet
where output voltage characteristics versus rated power were
expressed.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: This paper is an attempt to describe some of the results that had been found through a journey of study in the field of particle physics. This study consists of two parts, one about the measurement of the cross section of the decay of the Z particle in two electrons, and the other deals with the measurement of the cross section of the multi-photon absorption process using a beam of Laser in the Liquid Argon Time Projection Chamber.
The first part of the paper concerns the results based on the analysis of a data sample containing 8120 ee candidates to reconstruct the mass of the Z particle for each event where each event has an ee pair with PT(e) > 20GeV, and η(e) < 2.5. Monte Carlo templates of the reconstructed Z particle were produced as a function of the Z mass scale. The distribution of the reconstructed Z mass in the data was compared to the Monte Carlo templates, where the total cross section is calculated to be equal to 1432pb.
The second part concerns the Liquid Argon Time Projection Chamber, LAr TPC, the results of the interaction of the UV Laser, Nd-YAG with λ= 266mm, with LAr and through the study of the multi-photon ionization process as a part of the R&D at Bern University. The main result of this study was the cross section of the process of the multi-photon ionization process of the LAr, σe = 1.24±0.10stat±0.30sys.10 -56cm4.
Abstract: Sandwich construction is widely accepted as a method of construction especially in the aircraft industry. It is a type of stressed skin construction formed by bonding two thin faces to a thick core, the faces resist all of the applied edge loads and provide all or nearly all of the required rigidities, the core spaces the faces to increase cross section moment of inertia about common neutral axis and transmit shear between them provides a perfect bond between core and faces is made.
Material for face sheets can be of metal or reinforced plastics laminates, core material can be metallic cores of thin sheets forming corrugation or honeycomb, or non metallic core of Balsa wood, plastic foams, or honeycomb made of reinforced plastics.
For in plane axial loading web core and web-foam core Sandwich panels can fail by local buckling of plates forming the cross section with buckling wave length of the order of length of spacing between webs.
In this study local buckling of web core and web-foam core Sandwich panels is carried out for given materials of facing and core, and given panel overall dimension for different combinations of cross section geometries.
The Finite Strip Method is used for the analysis, and Fortran based computer program is developed and used.
Abstract: Radiation shielding is an obstacle in long duration space exploration. Boron Nitride Nanotubes (BNNTs) have attracted attention as an additive to radiation shielding material due to B10’s large neutron capture cross section. The B10 has an effective neutron capture cross section suitable for low energy neutrons ranging from 10-5 to 104 eV and hydrogen is effective at slowing down high energy neutrons. Hydrogenated BNNTs are potentially an ideal nanofiller for radiation shielding composites. We use Molecular Dynamics (MD) Simulation via Material Studios Accelrys 6.0 to model the Young’s Modulus of Hydrogenated BNNTs. An extrapolation technique was employed to determine the Young’s Modulus due to the deformation of the nanostructure at its theoretical density. A linear regression was used to extrapolate the data to the theoretical density of 2.62g/cm3. Simulation data shows that the hydrogenated BNNTs will experience a 11% decrease in the Young’s Modulus for (6,6) BNNTs and 8.5% decrease for (8,8) BNNTs compared to non-hydrogenated BNNT’s. Hydrogenated BNNTs are a viable option as a nanofiller for radiation shielding nanocomposite materials for long range and long duration space exploration.
Abstract: Resistance spot welding (RSW) has been used widely to join sheet metals. It has been a challenge to get required weld quality in spot welding of dissimilar thickness materials. Weld parameters are not generally available in standards for thickness beyond 4mm. This paper presents the welding process design and parameter optimization of RSW used in joining of low carbon steel sheet of thickness 0.8 mm and metal strips of cross section 10 x 5mm for electrical motor applications. Taguchi quality design was adopted for weld current and time optimization using L9 orthogonal array. Optimum process parameters (current- 3.5kA and time- 10 cycles) were obtained from the Taguchi analysis and shear test results. Confirmation experiment result revealed that the weld quality was within acceptable interval. Further, numerical simulation of RSW process was carried out with selected weld parameters to quantify the temperature at faying surface and check for formation of appropriate nugget. The nugget geometry measured after peel test and predicted from numerical validation method were similar and in accordance with the standards.
Abstract: Corpus luteum cross sectional (by ultrasonography) and plasma progesterone (by DELFIA) were estimated in early pregnant and non pregnant cows on days 14th and 20th to 23rd post insemination. On day 14th, corpus luteum sectional area was 348.43 mm2 in pregnant and 387.84mm2 in non pregnant cows. Within days 20th to 23rd, corpus luteum sectional area ranged between 342.06 and 367.90 mm2 in pregnant and between 193.85 and 270.69 mm2 in non pregnant cows. Plasma progesterone level was 2.43 ng/ml in pregnant and 2.46 ng/ml in non pregnant cows on day 14th, while during days 20th to 23rd the level ranged between 2.47 and 2.84 ng/ml in pregnant and between 0.53 and 1.17 ng/ml in non pregnant cows. Results of both luteal tissue areas as well as plasma progesterone levels were highly significantly deferent (P
Abstract: In this study, heat release performances of the three extruded-type heat sinks can be used in inverter for solar power generation were evaluated. Numbers of fins in the heat sinks (namely E-38, E-47 and E-76) were 38, 47 and 76, respectively. Heat transfer areas of them were 1.8, 1.9 and 2.8m2. The heat release performances of E-38, E-47 and E-76 heat sinks were measured as 79.6, 81.6 and 83.2%, respectively. The results of heat release performance show that the larger amount of heat transfer area the higher heat release rate. While on the other, in this experiment, variations of mass flow rates caused by different cross sectional areas of the three heat sinks may not be the major parameter of the heat release. Despite the 47.4% increment of heat transfer area of E-76 heat sink than that of E-47 one, its heat release rate was higher by only 2.0%; this suggests that its heat transfer area need to be optimized.
Abstract: This paper describes an underactuated robot hand operated by low-power actuators. It can grasp objects of various shapes using easy operations. This hand is suitable for use as a lightweight prosthetic hand that can grasp various objects using few input channels. To realize operations using a low-power actuator, a cross section deformation spring is proposed. The design procedure of the underactuated robot finger is proposed to realize an adaptive grasping movement. The validity of this mechanism and design procedure are confirmed through an object grasping experiment. Results demonstrate the effectiveness of across section deformation spring in reducing the actuator power. Moreover, adaptive grasping movement is realized by an easy operation.