Abstract: This paper describes a computer model of Quantum Field Theory (QFT), referred to in this paper as QTModel. After specifying the initial configuration for a QFT process (e.g. scattering) the model generates the possible applicable processes in terms of Feynman diagrams, the equations for the scattering matrix, and evaluates probability amplitudes for the scattering matrix and cross sections. The computations of probability amplitudes are performed numerically. The equations generated by QTModel are provided for demonstration purposes only. They are not directly used as the base for the computations of probability amplitudes. The computer model supports two modes for the computation of the probability amplitudes: (1) computation according to standard QFT, and (2) computation according to a proposed functional interpretation of quantum theory.
Abstract: A low-complexity, high-accurate frequency offset
estimation for multi-band orthogonal frequency division multiplexing (MB-OFDM) based ultra-wide band systems is presented regarding different carrier frequency offsets, different channel frequency
responses, different preamble patterns in different bands. Utilizing a
half-cycle Constant Amplitude Zero Auto Correlation (CAZAC) sequence as the preamble sequence, the estimator with a semi-cross
contrast scheme between two successive OFDM symbols is proposed. The CRLB and complexity of the proposed algorithm are derived.
Compared to the reference estimators, the proposed method achieves
significantly less complexity (about 50%) for all preamble patterns of the MB-OFDM systems. The CRLBs turn out to be of well performance.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: This paper presents a comparison between Spectrum-
Sliced Wavelength Division Multiplexing (SS-WDM) and Spectrum
Amplitude Coding Optical Code Division Multiple Access (SAC
Optical CDMA) systems for different light sources. The performance
of the system is shown in the simulated results of the bit error rate
(BER) and the eye diagram of both systems. The comparison results
indicate that the Multiple Access Interference (MAI) effects have a
significant impact on SS-WDM over SAC Optical CDMA systems.
Finally, in terms of spectral efficiency at constant BER of 10-12, SSWDM
offers higher spectral efficiency than optical CDMA since no
bandwidth expansion in needed.
Abstract: Method of multiple scales is used in the paper in order
to derive an amplitude evolution equation for the most unstable mode
from two-dimensional shallow water equations under the rigid-lid
assumption. It is assumed that shallow mixing layer is slightly curved
in the longitudinal direction and contains small particles. Dynamic
interaction between carrier fluid and particles is neglected. It is
shown that the evolution equation is the complex Ginzburg-Landau
equation. Explicit formulas for the computation of the coefficients of
the equation are obtained.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: In this paper, He-s amplitude frequency formulation is used to obtain a periodic solution for a nonlinear oscillator with fractional potential. By calculation and computer simulations, compared with the exact solution shows that the result obtained is of high accuracy.
Abstract: The method described in this paper deals with the problems of T-wave detection in an ECG. Determining the position of a T-wave is complicated due to the low amplitude, the ambiguous and changing form of the complex. A wavelet transform approach handles these complications therefore a method based on this concept was developed. In this way we developed a detection method that is able to detect T-waves with a sensitivity of 93% and a correct-detection ratio of 93% even with a serious amount of baseline drift and noise.
Abstract: In this paper, the application of the Mode Matching
(MM) method in the case of photonic crystal waveguide
discontinuities is presented. The structure under consideration is
divided into a number of cells, which supports a number of guided
and evanescent modes. These modes can be calculated numerically
by an alternative formulation of the plane wave expansion method
for each frequency. A matrix equation is then formed relating the
modal amplitudes at the beginning and at the end of the structure.
The theory is highly efficient and accurate and can be applied to
study the transmission sensitivity of photonic crystal devices due to
fabrication tolerances. The accuracy of the MM method is compared
to the Finite Difference Frequency Domain (FDFD) and the Adjoint
Variable Method (AVM) and good agreement is observed.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: This article proposes a current-mode square-rooting
circuit using current follower transconductance amplifier (CTFA).
The amplitude of the output current can be electronically controlled
via input bias current with wide input dynamic range. The proposed
circuit consists of only single CFTA. Without any matching
conditions and external passive elements, the circuit is then
appropriate for an IC architecture. The magnitude of the output signal
is temperature-insensitive. The PSpice simulation results are
depicted, and the given results agree well with the theoretical
anticipation. The power consumption is approximately 1.96mW at
±1.5V supply voltages.
Abstract: Extensive wind tunnel tests have been conducted to
investigate the unsteady flow field over and behind a 2D model of a
660 kW wind turbine blade section in pitching motion. The surface
pressure and wake dynamic pressure variation at a distance of 1.5
chord length from trailing edge were measured by pressure
transducers during several oscillating cycles at 3 reduced frequencies
and oscillating amplitudes. Moreover, form drag and linear
momentum deficit are extracted and compared at various conditions.
The results show that the wake velocity field and surface pressure of
the model have similar behavior before and after the airfoil beyond
the static stall angle of attack. In addition, the effects of reduced
frequency and oscillation amplitudes are discussed.
Abstract: Functional gastrointestinal disorders affect millions of people spread all age regardless of race and sex. There are, however, rare diagnostic methods for the functional gastrointestinal disorders because functional disorders show no evidence of organic and physical causes. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Aim of this study is, therefore, to develop a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristic above related to the rigidity of the gastrointestinal tract well. Ultrasound system was designed. The system consisted of transmitter, ultrasonic transducer, receiver, TGC, and CPLD, and verified via a phantom test. For the phantom test, ten soft-tissue specimens were harvested from porcine. Five of them were then treated chemically to mimic a rigid condition of gastrointestinal tract well, which was induced by functional gastrointestinal disorders. Additionally, the specimens were tested mechanically to identify if the mimic was reasonable. The customized ultrasound system was finally verified through application to human subjects with/without functional gastrointestinal disorders (Normal and Patient Groups). It was identified from the mechanical test that the chemically treated specimens were more rigid than normal specimen. This finding was favorably compared with the result obtained from the phantom test. The phantom test also showed that ultrasound system well described the specimen geometric characteristics and detected an alteration in the specimens. The maximum amplitude of the ultrasonic reflective signal in the rigid specimens (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal specimens (0.1±0.0Vp-p). Clinical tests using our customized ultrasound system for human subject showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3Vp-p) were generally higher than those in normal group (0.1±0.2Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These results suggest that newly designed diagnostic system based on ultrasound technique may diagnose enough the functional gastrointestinal disorders.
Abstract: Nonlinear response behaviour of a cracked RC beam under harmonic excitation is analysed to investigate various instability phenomena like, bifurcation, jump phenomena etc. The nonlinearity of the system arises due to opening and closing of the cracks in the RC beam and is modelled as a cubic polynomial. In order to trace different branches at the bifurcation point on the response curve (amplitude versus frequency of excitation plot), an arc length continuation technique along with the incremental harmonic balance (IHBC) method is employed. The stability of the solution is investigated by the Floquet theory using Hsu-s scheme. The periodic solutions obtained by the IHBC method are compared with these obtained by the numerical integration of the equation of motion. Characteristics of solutions fold bifurcation, jump phenomena and from stable to unstable zones are identified.
Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.
Abstract: Oil debris signal generated from the inductive oil
debris monitor (ODM) is useful information for machine condition
monitoring but is often spoiled by background noise. To improve the
reliability in machine condition monitoring, the high-fidelity signal
has to be recovered from the noisy raw data. Considering that the noise
components with large amplitude often have higher frequency than
that of the oil debris signal, the integral transform is proposed to
enhance the detectability of the oil debris signal. To cancel out the
baseline wander resulting from the integral transform, the empirical
mode decomposition (EMD) method is employed to identify the trend
components. An optimal reconstruction strategy including both
de-trending and de-noising is presented to detect the oil debris signal
with less distortion. The proposed approach is applied to detect the oil
debris signal in the raw data collected from an experimental setup. The
result demonstrates that this approach is able to detect the weak oil
debris signal with acceptable distortion from noisy raw data.
Abstract: Cardiac pulse-related artifacts in the EEG recorded
simultaneously with fMRI are complex and highly variable. Their
effective removal is an unsolved problem. Our aim is to develop an
adaptive removal algorithm based on the matching pursuit (MP)
technique and to compare it to established methods using a visual
evoked potential (VEP). We recorded the VEP inside the static
magnetic field of an MR scanner (with artifacts) as well as in an
electrically shielded room (artifact free). The MP-based artifact
removal outperformed average artifact subtraction (AAS) and
optimal basis set removal (OBS) in terms of restoring the EEG field
map topography of the VEP. Subsequently, a dipole model was fitted
to the VEP under each condition using a realistic boundary element
head model. The source location of the VEP recorded inside the MR
scanner was closest to that of the artifact free VEP after cleaning
with the MP-based algorithm as well as with AAS. While none of the
tested algorithms offered complete removal, MP showed promising
results due to its ability to adapt to variations of latency, frequency
and amplitude of individual artifact occurrences while still utilizing a
common template.
Abstract: In this paper, an ultrasonic technique is proposed to
predict oil content in a fresh palm fruit. This is accomplished by
measuring the attenuation based on ultrasonic transmission mode.
Several palm fruit samples with known oil content by Soxhlet
extraction (ISO9001:2008) were tested with our ultrasonic
measurement. Amplitude attenuation data results for all palm samples
were collected. The Feedforward Neural Networks (FNNs) are
applied to predict the oil content for the samples. The Root Mean
Square Error (RMSE) and Mean Absolute Error (MAE) of the FNN
model for predicting oil content percentage are 7.6186 and 5.2287
with the correlation coefficient (R) of 0.9193.
Abstract: In this paper we present a system for classifying videos
by frequency spectra. Many videos contain activities with repeating
movements. Sports videos, home improvement videos, or videos
showing mechanical motion are some example areas. Motion of these
areas usually repeats with a certain main frequency and several side
frequencies. Transforming repeating motion to its frequency domain
via FFT reveals these frequencies. Average amplitudes of frequency
intervals can be seen as features of cyclic motion. Hence determining
these features can help to classify videos with repeating movements.
In this paper we explain how to compute frequency spectra for video
clips and how to use them for classifying. Our approach utilizes series
of image moments as a function. This function again is transformed
into its frequency domain.
Abstract: Evolution of one-dimensional electron system under
high-energy-density (HED) conditions is investigated, using the
principle of least-action and variational method. In a single-mode
modulation model, the amplitude and spatial wavelength of the
modulation are chosen to be general coordinates. Equations of motion
are derived by considering energy conservation and force balance.
Numerical results show that under HED conditions, electron density
modulation could exist. Time dependences of amplitude and
wavelength are both positively related to the rate of energy input.
Besides, initial loading speed has a significant effect on modulation
amplitude, while wavelength relies more on loading duration.