Abstract: Fabric form-work is a technique to cast concrete structures with a great advantage of saving concrete material of up to 40%. This technique is particularly associated with the optimized concrete structures that usually have smaller cross-section dimensions than equivalent prismatic members. However, this can make the structural system produced from these members prone to smaller serviceability safety margins. Therefore, it is very important to understand the serviceability issue of non-prismatic concrete structures. In this paper, an analytical computer-based model to optimize concrete beams and to predict load-deflection behaviour of both prismatic and non-prismatic concrete beams is presented. The model was developed based on the method of sectional analysis and integration of curvatures. Results from the analytical model were compared to load-deflection behaviour of a number of beams with different geometric and material properties from other researchers. The results of the comparison show that the analytical program can accurately predict the load-deflection response of concrete beams with medium reinforcement ratios. However, it over-estimates deflection values for lightly reinforced specimens. Finally, the analytical program acceptably predicted load-deflection behaviour of on-prismatic concrete beams.
Abstract: In this paper, partial discharge analysis is performed in cavities artificially created in insulation. The setup is according with Cigre-II Method. Circular Samples created from Perspex Sheet with different configuration with changing number of cavities. Assessment of insulation health can be performed by Partial Discharge measurement as this has been found to be important means of condition monitoring. The experiments are done using MPD 540, which is a modern partial discharge measurement system. By analyzing the PD activity obtained for various voids/cavities, it is observed that the PD voltages show variation for cavity’s diameter, depth even for its ratios. This can be employed for scrutiny of insulation system.
Abstract: In this paper, an attribute weighting method called fuzzy C-means clustering based attribute weighting (FCMAW) for classification of Diabetes disease dataset has been used. The aims of this study are to reduce the variance within attributes of diabetes dataset and to improve the classification accuracy of classifier algorithm transforming from non-linear separable datasets to linearly separable datasets. Pima Indians Diabetes dataset has two classes including normal subjects (500 instances) and diabetes subjects (268 instances). Fuzzy C-means clustering is an improved version of K-means clustering method and is one of most used clustering methods in data mining and machine learning applications. In this study, as the first stage, fuzzy C-means clustering process has been used for finding the centers of attributes in Pima Indians diabetes dataset and then weighted the dataset according to the ratios of the means of attributes to centers of theirs. Secondly, after weighting process, the classifier algorithms including support vector machine (SVM) and k-NN (k- nearest neighbor) classifiers have been used for classifying weighted Pima Indians diabetes dataset. Experimental results show that the proposed attribute weighting method (FCMAW) has obtained very promising results in the classification of Pima Indians diabetes dataset.
Abstract: The under-5 mortality rate is high in sub-Saharan Africa with Lesotho being amongst the highest under-5 mortality rates in the world. The objective of the study is to determine the factors associated with under-5 mortality in Lesotho. The data used for this analysis come from the nationally representative household survey called the 2009 Lesotho Demographic and Health Survey. Odds ratios produced by the logistic regression models were used to measure the effect of each independent variable on the dependent variable. Female children were significantly 38% less likely to die than male children. Children who were breastfed for 13 to 18 months and those who were breastfed for more than 19 months were significantly less likely to die than those who were breastfed for 12 months or less. Furthermore, children of mothers who stayed in Quthing, Qacha’s Nek and Thaba Tseka ran the greatest risk of dying. The results suggested that: sex of child, type of birth, breastfeeding duration, district, source of energy and marital status were significant predictors of under-5 mortality, after correcting for all variables.
Abstract: In this paper, triangular lattice index-guiding photonic crystal fibers (PCFs) are synthesized to compensate the chromatic dispersion of a single mode fiber (SMF-28) for an 80 km optical link operating at 1.55 µm, by using the directed tabu search algorithm. Hole-to-hole distance, circular air-hole diameter, solid-core diameter, ring number and PCF length parameters are optimized for this purpose. Three Synthesized PCFs with different physical parameters are compared in terms of their objective functions values, residual dispersions and compensation ratios.
Abstract: Niosomes were formulated with an aim of enhancing the oral bioavailability of losartan potassium and formulated in different molar ratios of surfactant, cholesterol and dicetyl phosphate. The formulated niosomes were found in range of 54.98 µm to 107.85 µm in size. Formulations with 1:1 ratio of surfactant and cholesterol have shown maximum entrapment efficiencies. Niosomes with sorbitan monostearate showed maximum drug release and zero order release kinetics, at the end of 24 hours. The in vivo study has shown the significant enhancement in oral bioavailability of losartan potassium in rats, after a dose of 10 mg/kg. The average relative bioavailability in relation with pure drug solution was found 2.56, indicates more than two fold increase in oral bioavailability. A significant increment in MRT reflects the release retarding ability of the vesicles. In conclusion, niosomes could be a promising delivery of losartan potassium with improved oral bioavailability and prolonged release profiles.
Abstract: With the rapid development of computer technology,
the design of computers and keyboards moves towards a trend of
slimness. The change of mobile input devices directly influences
users’ behavior. Although multi-touch applications allow entering
texts through a virtual keyboard, the performance, feedback, and
comfortableness of the technology is inferior to traditional keyboard,
and while manufacturers launch mobile touch keyboards and
projection keyboards, the performance has not been satisfying.
Therefore, this study discussed the design factors of slim
pressure-sensitive keyboards. The factors were evaluated with an
objective (accuracy and speed) and a subjective evaluation
(operability, recognition, feedback, and difficulty) depending on the
shape (circle, rectangle, and L-shaped), thickness (flat, 3mm, and
6mm), and force (35±10g, 60±10g, and 85±10g) of the keyboard.
Moreover, MANOVA and Taguchi methods (regarding
signal-to-noise ratios) were conducted to find the optimal level of each
design factor. The research participants, by their typing speed (30
words/ minute), were divided in two groups. Considering the
multitude of variables and levels, the experiments were implemented
using the fractional factorial design. A representative model of the
research samples were established for input task testing. The findings
of this study showed that participants with low typing speed primarily
relied on vision to recognize the keys, and those with high typing
speed relied on tactile feedback that was affected by the thickness and
force of the keys. In the objective and subjective evaluation, a
combination of keyboard design factors that might result in higher
performance and satisfaction was identified (L-shaped, 3mm, and
60±10g) as the optimal combination. The learning curve was analyzed
to make a comparison with a traditional standard keyboard to
investigate the influence of user experience on keyboard operation.
The research results indicated the optimal combination provided input
performance to inferior to a standard keyboard. The results could serve
as a reference for the development of related products in industry and
for applying comprehensively to touch devices and input interfaces
which are interacted with people.
Abstract: Temperature distribution investigation in a conical diffuser fitted with helical screw-tape with and without center-rod is studied numerically. A helical screw-tape is inserted in the diffuser to create swirl flow that helps to enhance the temperature distribution rate with inlet Reynolds number 4.3 x 104. Three pitch lengths ratios (Y/L = 0.153, 0.23 and 0.307) for the helical screw-tape with and without center-rod are simulated and compared. The geometry of the conical diffuser and the inlet condition for both arrangements are kept constant. Numerical findings show that the helical screw-tape inserts without center-rod perform significantly better than the helical tape inserts with center-rod in the conical diffuser.
Abstract: The power generated by eight point absorber type wave energy converters each having a different buoy are calculated in order to investigate the performances of buoys in this study. The calculations are carried out by modeling three different sea states observed in two different locations in the Black Sea. The floats analyzed in this study have two basic geometries and four different draft/radius (d/r) ratios. The buoys possess the shapes of a semi-ellipsoid and a semi-elliptic paraboloid. Additionally, the draft/radius ratios range from 0.25 to 1 by an increment of 0.25. The radiation forces acting on the buoys due to the oscillatory motions of these bodies are evaluated by employing a 3D panel method along with a distribution of 3D pulsating sources in frequency domain. On the other hand, the wave forces acting on the buoys which are taken as the sum of Froude-Krylov forces and diffraction forces are calculated by using linear wave theory. Furthermore, the wave energy converters are assumed to be taut-moored to the seabed so that the secondary body which houses a power take-off system oscillates with much smaller amplitudes compared to the buoy. As a result, it is assumed that there is not any significant contribution to the power generation from the motions of the housing body and the only contribution to power generation comes from the buoy. The power take-off systems of the wave energy converters are high pressure oil hydraulic systems which are identical in terms of their characteristic parameters. The results show that the power generated by wave energy converters which have semi-ellipsoid floats is higher than that of those which have semi elliptic paraboloid floats in both locations and in all sea states. It is also determined that the power generated by the wave energy converters follow an unsteady pattern such that they do not decrease or increase with changing draft/radius ratios of the floats. Although the highest power level is obtained with a semi-ellipsoid float which has a draft/radius ratio equal to 1, other floats of which the draft/radius ratio is 0.25 delivered higher power that the floats with a draft/radius ratio equal to 1 in some cases.
Abstract: This paper describes a method for AWGN (Additive White Gaussian Noise) variance estimation in noisy stochastic signals, referred to as Multiplicative-Noising Variance Estimation (MNVE). The aim was to develop an estimation algorithm with minimal number of assumptions on the original signal structure. The provided MATLAB simulation and results analysis of the method applied on speech signals showed more accuracy than standardized AR (autoregressive) modeling noise estimation technique. In addition, great performance was observed on very low signal-to-noise ratios, which in general represents the worst case scenario for signal denoising methods. High execution time appears to be the only disadvantage of MNVE. After close examination of all the observed features of the proposed algorithm, it was concluded it is worth of exploring and that with some further adjustments and improvements can be enviably powerful.
Abstract: This paper is concerned with microwave (MW) ablation for a liver cancer tissue by using helix antenna. The antenna structure supports the propagation of microwave energy at 2.45 GHz. A 1½ turn spiral catheter-based microwave antenna applicator has been developed. We utilize the three-dimensional finite element method (3D FEM) simulation to analyze where the tissue heat flux, lesion pattern and volume destruction during MW ablation. The configurations of helix antenna where Helix air-core antenna and Helix Dielectric-core antenna. The 3D FEMs solutions were based on Maxwell and bio-heat equations. The simulation protocol was power control (10 W, 300s). Our simulation result, both helix antennas have heat flux occurred around the helix antenna and that can be induced the temperature distribution similar (teardrop). The region where the temperature exceeds 50°C the microwave ablation was successful (i.e. complete destruction). The Helix air-core antenna and Helix Dielectric-core antenna, ablation zone or axial ratios (Widest/length) were respectively 0.82 and 0.85; the complete destructions were respectively 4.18 cm3 and 5.64 cm3
Abstract: An experiment to verify the relationships between
physiological indexes of an e-learner and the presence or absence of an
operation during e-learning is described. Electroencephalogram
(EEG), hemoencephalography (HEG), skin conductance (SC), and
blood volume pulse (BVP) values were measured while participants
performed experimental learning tasks. The results show that there are
significant differences between the SC values when reading with
clicking on learning materials and the SC values when reading without
clicking, and between the HEG ratio when reading (with and without
clicking) and the HEG ratio when resting for four of five participants.
We conclude that the SC signals can be used to estimate whether or not
a learner is performing an active task and that the HEG ratios can be
used to estimate whether a learner is learning.
Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: In this study, the potential benefits of playing action
video game among congenitally deaf and dumb subjects is reported in
terms of EEG ratio indices. The frontal and occipital lobes are
associated with development of motor skills, cognition, and visual
information processing and color recognition. The sixteen hours of
First-Person shooter action video game play resulted in the increase
of the ratios β/(α+θ) and β/θ in frontal and occipital lobes. This can
be attributed to the enhancement of certain aspect of cognition among
deaf and dumb subjects.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: This paper focuses on the study of DC-to-DC
converters, which are suitable for low-voltage high-power
applications. The output voltages generated by renewable energy
sources such as photovoltaic arrays and fuel cell stacks are
generally low and required to be increased to high voltage levels.
Development of DC-to-DC converters, which provide high step-up
voltage conversion ratios with high efficiencies and low voltage
stresses, is one of the main issues in the development of renewable
energy systems. A procedure for three converters−conventional
DC-to-DC converter, interleaved boost converter, and isolated flyback
based converter, is illustrated for a given set of specifications. The
selection among the converters for the given application is based on
the voltage conversion ratio, efficiency, and voltage stresses.
Abstract: Zinc borates are used as a multi-functional flame
retardant additive for its high dehydration temperature. In this study,
the method of ultrasonic mixing was used in the synthesis of zinc
borates. The reactants of zinc oxide (ZnO) and boric acid (H3BO3)
were used at the constant reaction parameters of 90°C reaction
temperature and 55 min of reaction time. Several molar ratios of
ZnO:H3BO3 (1:1, 1:2, 1:3, 1:4 and 1:5) were conducted for the
determination of the optimum reaction ratio. Prior to synthesis the
characterization of the synthesized zinc borates were made by X-Ray
Diffraction (XRD) and Fourier Transform Infrared Spectroscopy
(FT-IR). From the results Zinc Oxide Borate Hydrate
[Zn3B6O12.3.5H2O], were synthesized optimum at the molar ratio of
1:3, with a reaction efficiency of 95.2%.
Abstract: The goal of this paper is to specify factors influencing
the profitability of selected banks. Next, a model will be created to
help establish variables that have a demonstrable influence on the
development of the selected banks' profitability ratios. Czech banks
and their international parent companies were selected for analyzing
profitability. Banks categorized as large banks (according to the
Czech National Bank's system, which ranks banks according to
balance sheet total) were selected to represent the Czech banks. Two
ratios, the return on assets ratio (ROA) and the return on equity ratio
(ROE) are used to assess bank profitability. Six endogenous and four
external indicators were selected from among other factors that
influence bank profitability. The data analyzed were for 2001–2013.
First, correlation analysis, which was supposed to eliminate
correlated values, was conducted. A large number of correlated
values were established on the basis of this analysis. The strongly
correlated values were omitted. Despite this, the subsequent
regression analysis of profitability for the individual banks that were
selected did not confirm that the selected variables influenced their
profitability. The studied factors' influence on bank profitability was
demonstrated only for Ceskoslovenska Obchodni Banka and Société
Générale using regression analysis. For Československa Obchodni
Banka, it was demonstrated that inflation level and the amount of the
central bank's interest rate influenced the return on assets ratio and
that capital adequacy and market concentration influenced the return
on equity ratio for Société Générale.
Abstract: The aim of the study was to investigate the effect of
Saccharomyces cerevisiae (SC) live yeast culture on microbial
protein supply to small intestine in Kivircik male yearlings when fed
with different ratio of forage and concentrate diets. Four Kivircik
male yearlings with permanent rumen canula were used in the
experiment. The treatments were allocated to a 4x4 Latin square
design. Diet I consisted of 70% alfalfa hay and 30% concentrate, Diet
II consisted of 30% alfalfa hay and 70% concentrate, Diet I and II
were supplemented with a SC. Daily urine was collected and stored at
-20°C until analysis. Calorimetric methods were used for the
determination of urinary allantoin and creatinine levels. The
estimated microbial N supply to small intestine for Diets I, I+SC, II
and II+SC were 2.51, 2.64, 2.95 and 3.43 g N/d respectively.
Supplementation of Diets I and II with SC significantly affected the
allantoin levels in μmol/W0.75 (p
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.