Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: The introduction of sowing technologies into minimum- or no-tillage soil has a number of economical and environmental virtues, such as improving soil properties, decreasing soil erosion and degradation, and saving working time and fuel. However, the main disadvantage of these technologies is that plant residues on the soil surface reduce the quality of the planted crop seeds, thus requiring plant residues to be removed or cut. This paper presents a analysis of disc coulter parameters and an experimental investigation of cutting spring barley straw containing various amounts of moisture with different disc coulters (smooth and notched).
Abstract: The two-phase flow field and the motion of the free
surface in an oscillating channel are simulated numerically to assess
the methodology for simulating nuclear reacotr thermal hydraulics
under seismic conditions. Two numerical methods are compared: one
is to model the oscillating channel directly using the moving grid of
the Arbitrary Lagrangian-Eulerian method, and the other is to simulate
the effect of channel motion using the oscillating acceleration acting
on the fluid in the stationary channel. The two-phase flow field in the
oscillating channel is simulated using the level set method in both
cases. The calculated results using the oscillating acceleration are
found to coinside with those using the moving grid, and the theoretical
back ground and the limitation of oscillating acceleration are discussed.
It is shown that the change in the interfacial area between liquid and
gas phases under seismic conditions is important for nuclear reactor
thermal hydraulics.
Abstract: This study presents a mathematical modeling approach to the planning of HIV therapies on an individual basis. The model replicates clinical data from typical-progressors to AIDS for all stages of the disease with good agreement. Clinical data from rapid-progressors and long-term non-progressors is also matched by estimation of immune system parameters only. The ability of the model to reproduce these phenomena validates the formulation, a fact which is exploited in the investigation of effective therapies. The therapy investigation suggests that, unlike continuous therapy, structured treatment interruptions (STIs) are able to control the increase in both the drug-sensitive and drug-resistant virus population and, hence, prevent the ultimate progression from HIV to AIDS. The optimization results further suggest that even patients characterised by the same progression type can respond very differently to the same treatment and that the latter should be designed on a case-by-case basis. Such a methodology is presented here.
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Abstract: We have developed a computer program consisting of
6 subtests assessing the children hand dexterity applicable in the
rehabilitation medicine. We have carried out a normative study on a
representative sample of 285 children aged from 7 to 15 (mean age
11.3) and we have proposed clinical standards for three age groups
(7-9, 9-11, 12-15 years). We have shown statistical significance of
differences among the corresponding mean values of the task time
completion. We have also found a strong correlation between the task
time completion and the age of the subjects, as well as we have
performed the test-retest reliability checks in the sample of 84
children, giving the high values of the Pearson coefficients for the
dominant and non-dominant hand in the range 0.740.97 and
0.620.93, respectively.
A new MATLAB-based programming tool aiming at analysis of
cardiologic RR intervals and blood pressure descriptors, is worked
out, too. For each set of data, ten different parameters are extracted: 2
in time domain, 4 in frequency domain and 4 in Poincaré plot
analysis. In addition twelve different parameters of baroreflex
sensitivity are calculated. All these data sets can be visualized in time
domain together with their power spectra and Poincaré plots. If
available, the respiratory oscillation curves can be also plotted for
comparison. Another application processes biological data obtained
from BLAST analysis.
Abstract: The inherent complexity in nowadays- business
environments is forcing organizations to be attentive to the dynamics
in several fronts. Therefore, the management of technological
innovation is continually faced with uncertainty about the future.
These issues lead to a need for a systemic perspective, able to analyze
the consequences of interactions between different factors. The field
of technology foresight has proposed methods and tools to deal with
this broader perspective. In an attempt to provide a method to analyze
the complex interactions between events in several areas, departing
from the identification of the most strategic competencies, this paper
presents a methodology based on the Delphi method and Quality
Function Deployment. This methodology is applied in a sheet metal
processing equipment manufacturer, as a case study.
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of thermal treatment in flexible
retort pouch packaging on the quality of potatoes’ produce during the
storage time. Samples were evaluated immediately after retort
thermal treatment; and following 1; 2; 3 and 4 storage months at the
ambient temperature of +18±2ºC in vacuum packaging from
polyamide/polyethylene (PA/PE) and aluminum/polyethylene
(Al/PE) film pouches with barrier properties. Experimentally the
quality of the potatoes’ produce in dry butter and mushroom
dressings was characterized by measuring pH, hardness, color,
microbiological properties and sensory evaluation. The sterilization
was effective in protecting the produce from physical, chemical, and
microbial quality degradation. According to the study of obtained
data, it can be argued that the selected product processing technology
and packaging materials could be applied to provide the safety and
security during four-month storage period.
Abstract: Cooperative organizations in Malaysia are going
through a phase of rapid growth. They are seen by the government as
another crucial vehicle to drive and boost up the country-s
economical development and growth. Hence, the issue of cooperative
governance is of great importance. Unlike literatures on corporate
governance for public listed companies-, literatures on governance
for social enterprises, in particular the cooperative organizations are
still at the early stage in Malaysia and very scant in number. This
paper will look into current practices as well as issues and challenges
related to cooperative governance. The need for a better solution
towards forming best practices of cooperative governance framework
appears imperative in deterring cases of mismanagement and fraud.
Abstract: Energy dissipation in drops has been investigated by
physical models. After determination of effective parameters on the
phenomenon, three drops with different heights have been
constructed from Plexiglas. They have been installed in two existing
flumes in the hydraulic laboratory. Several runs of physical models
have been undertaken to measured required parameters for
determination of the energy dissipation. Results showed that the
energy dissipation in drops depend on the drop height and discharge.
Predicted relative energy dissipations varied from 10.0% to 94.3%.
This work has also indicated that the energy loss at drop is mainly
due to the mixing of the jet with the pool behind the jet that causes
air bubble entrainment in the flow. Statistical model has been
developed to predict the energy dissipation in vertical drops denotes
nonlinear correlation between effective parameters. Further an
artificial neural networks (ANNs) approach was used in this paper to
develop an explicit procedure for calculating energy loss at drops
using NeuroSolutions. Trained network was able to predict the
response with R2 and RMSE 0.977 and 0.0085 respectively. The
performance of ANN was found effective when compared to
regression equations in predicting the energy loss.
Abstract: Food and fibre production in arid and semi-arid regions has emerged as one of the major challenges for various socio-economic and political reasons such as the food security and self-sufficiency. Productive use of the renewable water resources has risen on top ofthe decision-making agenda. For this reason, efficient operation and maintenance of modern irrigation and drainage schemes become part and parcel and indispensible reality in agricultural policy making arena. The aim of this paper is to investigate the complexity of operating and maintaining such schemes, mainly focussing on challenges which enhance and opportunities that impedsustainable food and fibre production. The methodology involved using secondary data complemented byroutine observations and stakeholders views on issues that influence the O&M in the Dez command area. The SPSS program was used as an analytical framework for data analysis and interpretation.Results indicate poor application efficiency in most croplands, much of which is attributed to deficient operation of conveyance and distribution canals. These in turn, are reportedly linked to inadequate maintenance of the pumping stations and hydraulic structures like turnouts,flumes and other control systems particularly in the secondary and tertiary canals. Results show that the aforementioned deficiencies have been the major impediment to establishing regular flow toward the farm gates which subsequently undermine application efficiency and tillage operationsat farm level. Results further show that accumulative impact of such deficiencies has been the major causes of poorcrop yield and quality that deem production system in these croplands uneconomic. Results further show that the present state might undermine the sustainability of agricultural system in the command area. The overall conclusion being that present water management is unlikely to be responsive to challenges that the sector faces. And in the absence of coherent measures to shift the status quo situation in favour of more productive resource use, it would be hard to fulfil the objectives of the National Economic and Socio-cultural Development Plans.
Abstract: A spatial analysis of a large 20th century urban settlement (town/city) easily presents the celebrated central Business District (CBD). Theories of Urban Land Economics have easily justified and attempted to explain the existence of such a district activity area within the cityscape. This work examines the gradual emergence and development of the CBD in Lafia Town, Nigeria over 20 years and the attended urban problems caused by its emergence. Personal knowledge and observation of land use change are the main sources of data for the work, with unstructured interview with residents. The result are that the absence of a co-ordinate land use plan for the town, multi-nuclei nature, and regional location of surrounding towns have affected the growth pattern, hence the CBD. Traffic congestion, dispersed CBD land uses are some of the urban planning problems. The work concludes by advocating for integrating CBD uses.
Abstract: With continuous rise of oil price, how to develop alternative energy source has become a hot topic around the world. This study discussed the dynamic characteristics of an island power system operating under random wind speed lower than nominal wind
speeds of wind turbines. The system primarily consists of three diesel engine power generation systems, three constant-speed variable-pitch wind turbines, a small hydraulic induction generation system, and lumped static loads. Detailed models based on Matlab/Simulink were developed to cater for the dynamic behavior of the system. The results suggested this island power system can operate stably in this operational mode. This study can serve as an important reference for planning, operation, and further expansion of island power systems.
Abstract: In this paper, we studied some properties of geodesic on some open surfaces: Hyperboloid, Paraboloid and Funnel Surface. Geodesic equation in the v-Clairaut parameterization was calculated and reduced to definite integral. Some geodesics on some open surfaces as mention above were classified by Clairaut's relation.
Abstract: This paper focuses on the probabilistic numerical
solution of the problems in biomechanics and mining. Applications of
Simulation-Based Reliability Assessment (SBRA) Method are
presented in the solution of designing of the external fixators applied
in traumatology and orthopaedics (these fixators can be applied for
the treatment of open and unstable fractures etc.) and in the solution
of a hard rock (ore) disintegration process (i.e. the bit moves into the
ore and subsequently disintegrates it, the results are compared with
experiments, new design of excavation tool is proposed.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Scouring around a bridge pier is a complex
phenomenon. More laboratory experiments are required to
understand the scour mechanism. This paper focused on time
development of local scour around piers and piles in semi integral
bridges. Laboratory data collected at Hydraulics Laboratory,
University of Malaya was analyzed for this purpose. Tests were
performed with two different uniform sediment sizes and five ranges
of flow velocities. Fine and coarse sediments were tested in the
flume. Results showed that scour depths for both pier and piles
increased with time up to certain levels and after that they became
almost constant. It had been found that scour depths increased when
discharges increased. Coarser sediment also produced lesser scouring
at the piers and combined piles.
Abstract: The objective of the present investigation was to
evaluate the morphology of Escherchia coli bacteria in interaction
with SiO2 nanoparticles.
This study was made by atomic force microscopy and quartz
crystal microbalance using SiO2 nanoparticles with 10nm, 50nm and
100nm diameter and bacteria immobilized on polyelectrolyte
multilayer films obtained by spin coating or by “layer by layer”
(LbL) method.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.