Abstract: Industrial drives are source of serious power quality problems. In this, two typical industrial drives have been dealt with, namely, FOC induction motor drives and DTC induction motor drive. The Z-source inverter is an emerging topology of power electronic converters which is capable of buck boost characteristics. The performances of different control methods based Z-source inverters feeding these industrial drives have been investigated, in this work. The test systems have been modeled and simulated in MATLAB/SIMULINK. The results obtained after carrying out these simulations have been used to draw the conclusions.
Abstract: The power electronic components within Electric Vehicles (EV) need to operate in several important modes. Some modes directly influence safety, while others influence vehicle performance. Given the variety of functions and operational modes required of the power electronics, it needs to meet efficiency requirements to minimize power losses. Another challenge in the control and construction of such systems is the ability to support bidirectional power flow. This paper considers the construction, operation, and feasibility of available converters for electric vehicles with feasible configurations of electrical buses and loads. This paper describes logic and control signals for the converters for different operations conditions based on the efficiency and energy usage bases.
Abstract: As per the statistical data, the Doubly-fed Induction
Generator (DFIG) based wind turbine with variable speed and
variable pitch control is the most common wind turbine in the
growing wind market. This machine is usually used on the grid
connected wind energy conversion system to satisfy grid code
requirements such as grid stability, Fault Ride Through (FRT), power
quality improvement, grid synchronization and power control etc.
Though the requirements are not fulfilled directly by the machine, the
control strategy is used in both the stator as well as rotor side along
with power electronic converters to fulfil the requirements stated
above. To satisfy the grid code requirements of wind turbine, usually
grid side converter is playing a major role. So in order to improve the
operation capacity of wind turbine under critical situation, the
intensive study of both machine side converter control and grid side
converter control is necessary In this paper DFIG is modeled using
power components as variables and the performance of the DFIG
system is analysed under grid voltage fluctuations. The voltage
fluctuations are made by lowering and raising the voltage values in
the utility grid intentionally for the purpose of simulation keeping in
view of different grid disturbances.
Abstract: In this paper, a direct power control (DPC)
strategies have been investigated in order to control a high
power AC/DC converter with time variable load. This converter
is composed of a three level three phase neutral point clamped
(NPC) converter as rectifier and an H-bridge four quadrant
current control converter. In the high power application,
controller not only must adjust the desire outputs but also
decrease the level of distortions which are injected to the network
from the converter. Regarding to this reason and nonlinearity
of the power electronic converter, the conventional controllers
cannot achieve appropriate responses. In this research, the
precise mathematical analysis has been employed to design the
appropriate controller in order to control the time variable
load. A DPC controller has been proposed and simulated using
Matlab/ Simulink. In order to verify the simulation result, a real
time simulator- OPAL-RT- has been employed. In this paper,
the dynamic response and stability of the high power NPC
with variable load has been investigated and compared with
conventional types using a real time simulator. The results proved
that the DPC controller is more stable and has more precise
outputs in comparison with conventional controller.
Abstract: Nowadays, Photovoltaic-PV Farms/ Parks and large
PV-Smart Grid Interface Schemes are emerging and commonly
utilized in Renewable Energy distributed generation. However, PVhybrid-
Dc-Ac Schemes using interface power electronic converters
usually has negative impact on power quality and stabilization of
modern electrical network under load excursions and network fault
conditions in smart grid. Consequently, robust FACTS based
interface schemes are required to ensure efficient energy utilization
and stabilization of bus voltages as well as limiting switching/fault
onrush current condition. FACTS devices are also used in smart grid-
Battery Interface and Storage Schemes with PV-Battery Storage
hybrid systems as an elegant alternative to renewable energy
utilization with backup battery storage for electric utility energy and
demand side management to provide needed energy and power
capacity under heavy load conditions. The paper presents a robust
interface PV-Li-Ion Battery Storage Interface Scheme for
Distribution/Utilization Low Voltage Interface using FACTS
stabilization enhancement and dynamic maximum PV power tracking
controllers.
Digital simulation and validation of the proposed scheme is done
using MATLAB/Simulink software environment for Low Voltage-
Distribution/Utilization system feeding a hybrid Linear-Motorized
inrush and nonlinear type loads from a DC-AC Interface VSC-6-
pulse Inverter Fed from the PV Park/Farm with a back-up Li-Ion
Storage Battery.
Abstract: Power quality in terms of power factor, THD and precisely regulated output voltage are the major key factors for efficient operation of power electronic converters. This paper presents an easy and effective active wave shaping control scheme for the pulsed input current drawn by the uncontrolled diode bridge rectifier thereby achieving power factor nearer to unity and also satisfying the THD specifications. It also regulates the output DC-bus voltage. CCM boost power factor correction with constant frequency operation features smaller inductor current ripple resulting in low RMS currents on inductor and switch thus leading to low electromagnetic interference. The objective of this work is to develop an active PFC control circuit using CCM boost converter implementing variable duty cycle control. The proposed scheme eliminates inductor current sensing requirements yet offering good performance and satisfactory results for maintaining the power quality. Simulation results have been presented which covers load changes also.
Abstract: The selection of control strategy depends on the converters of the drive including power, speed, performance and the possible system costs. A number of attempts were therefore made in recent times to develop novel power electronic converter structures for SRM drives, based on the utilization. Many of the converters with variable speed drives have no input power factor correction circuits. This results in harmonic pollution of the utility supply, which should be avoided. The effect of power factor variation in terms of harmonic content is also analyzed in this study. The proposed topologies were simulated using MATLAB / Simulink software package and the results are obtained.
Abstract: Voltage flicker is a disturbance in electrical power
systems. The reason for this disturbance is mainly the large nonlinear
loads such as electric arc furnaces. Synchronous static
compensator (STATCOM) is considered as a proper technique to
mitigate the voltage flicker. Application of more suitable and precise
power electronic converter leads to a more precise performance of the
compensator. In this paper a three-level 12-pulse voltage source
inverter (VSI) with a 12-terminal transformer connected to the ac
system is studied and the obtained results are compared with the
performance of a STATCOM using a simple two-level VSI and an
optimal and more precise performance of the proposed scheme is
achieved.
Abstract: Selective harmonic elimination-pulse width modulation techniques offer a tight control of the harmonic spectrum of a given voltage waveform generated by a power electronic converter along with a low number of switching transitions. Traditional optimization methods suffer from various drawbacks, such as prolonged and tedious computational steps and convergence to local optima; thus, the more the number of harmonics to be eliminated, the larger the computational complexity and time. This paper presents a novel method for output voltage harmonic elimination and voltage control of PWM AC/AC voltage converters using the principle of hybrid Real-Coded Genetic Algorithm-Pattern Search (RGA-PS) method. RGA is the primary optimizer exploiting its global search capabilities, PS is then employed to fine tune the best solution provided by RGA in each evolution. The proposed method enables linear control of the fundamental component of the output voltage and complete elimination of its harmonic contents up to a specified order. Theoretical studies have been carried out to show the effectiveness and robustness of the proposed method of selective harmonic elimination. Theoretical results are validated through simulation studies using PSIM software package.
Abstract: In this paper the authors propose a flexible electronic solution, to improve the energetic efficiency of a thermo plant. This is achieved by replacing the mechanical gear box, placed traditionally between a gas turbine and a synchronous generator; by a power electronic converter. After reminding problematic of gear boxes and interest of a proposed electronic solution in high power plants, the authors describe a new control strategy for an indirect frequency converter, which is characterized by its high efficiency due to the use of SWM: Square Wave Modulation. The main advantage of this mode is the quasi absence of switching losses. A control method is also proposed to resolve some problems incurred by using square wave modulation, in particular to reduce the harmonics distortion of the output inverter voltage and current. Simulation examples as well as experimental results are included.