Abstract: Evaluation of dynamic earth pressure on retaining wall is a topic of primary importance. In present paper, dynamic active earth pressure and displacement of flexible cantilever retaining wall has been evaluated analytically using 2-DOF mass-spring-dashpot model by incorporating both wall and backfill properties. The effect of wall flexibility on dynamic active earth pressure and wall displacement are studied and presented in graphical form. The obtained results are then compared with the various conventional methods, experimental analysis and also with PLAXIS analysis. It is observed that the dynamic active earth pressure decreases with increase in the wall flexibility while wall displacement increases linearly with flexibility of the wall. The results obtained by proposed 2-DOF analytical model are found to be more realistic and economical.
Abstract: In this study, typical c-ɸ soils subjected to loadings were assessed with a view to understand the general stress distribution and settlement behaviour of the soils under drained conditions. Numerical estimations of the non-dimensional bearing capacity factors, Nq and Nγ for varied angles of friction in the soil mass were obtained using PLAXIS. Ultimate bearing capacity values over a Ф range of 0-30 degrees were also computed and compared with analytical results obtained from the traditional simplified uncoupled approach of Terzaghi and Meyerhof. Results from the numerical study agree well with theoretical findings.
Abstract: Structures on the ground surface bear impact from the tunneling-induced settlement, especially when twin tunnels are constructed. The tunneling influence on the structure is considered as a critical issue based on the construction procedure and relative position of tunnels. Lebanon is suffering from a traffic phenomenon caused by the lack of transportation systems. After several traffic counts and geotechnical investigations in Beirut city, efforts aim for the construction of tunneling systems. In this paper, we present a non-linear numerical modeling of the effect of the twin tunnels constructions on the structures located at soil surface for a particular site in Beirut. A parametric study, which concerns the geometric configuration of tunnels, the distance between their centers, the construction order, and the position of the structure, is performed. The tunnel-soil-structure interaction is analyzed by using the non-linear finite element modeling software PLAXIS 2D. The results of the surface settlement and the bending moment of the structure reveal significant influence when the structure is moved away, especially in vertical aligned tunnels.
Abstract: This study aims at analysing the load settlement behavior and predict the bearing capacity of piled raft foundation a series of finite element models with different foundation configurations and stiffness were established. Numerical modeling is used to study the behavior of the piled raft foundation due to the complexity of piles, raft, and soil interaction and also due to the lack of reliable analytical method that can predict the behavior of the piled raft foundation system. Simple analytical models are developed to predict the average settlement and the load sharing between the piles and the raft in piled raft foundation system. A simple example to demonstrate the applications of these charts is included.
Abstract: Soil improvement using vibro stone column techniques consists of two main parts: (1) the installed load bearing columns of well-compacted, coarse-grained material and (2) the improvements to the surrounding soil due to vibro compaction. Extensive research work has been carried out over the last 20 years to understand the improvement in the composite foundation performance due to the second part mentioned above. Nevertheless, few of these studies have tried to quantify some of the key design parameters, namely the changes in the stiffness and stress state of the treated soil, or have consider these parameters in the design and calculation process. Consequently, empirical and conservative design methods are still being used by ground improvement companies with a significant variety of results in engineering practice. Two-dimensional finite element study to develop an axisymmetric model of a single stone column reinforced foundation was performed using PLAXIS 2D AE to quantify the effect of the vibro installation of this column in soft saturated clay. Settlement and bearing performance were studied as an essential part of the design and calculation of the stone column foundation. Particular attention was paid to the large deformation in the soft clay around the installed column caused by the lateral expansion. So updated mesh advanced option was taken in the analysis. In this analysis, different degrees of stone column lateral expansions were simulated and numerically analyzed, and then the changes in the stress state, stiffness, settlement performance and bearing capacity were quantified. It was found that application of radial expansion will produce a horizontal stress in the soft clay mass that gradually decrease as the distance from the stone column axis increases. The excess pore pressure due to the undrained conditions starts to dissipate immediately after finishing the column installation, allowing the horizontal stress to relax. Changes in the coefficient of the lateral earth pressure K ٭, which is very important in representing the stress state, and the new stiffness distribution in the reinforced clay mass, were estimated. More encouraging results showed that increasing the expansion during column installation has a noticeable effect on improving the bearing capacity and reducing the settlement of reinforced ground, So, a design method should include this significant effect of the applied lateral displacement during the stone column instillation in simulation and numerical analysis design.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: Liquefaction is a phenomenon in which the strength
and stiffness of a soil is reduced by earthquake shaking or other rapid
cyclic loading. Liquefaction and related phenomena have been
responsible for huge amounts of damage in historical earthquakes
around the world.
Modeling of soil behavior is the main step in soil liquefaction
prediction process. Nowadays, several constitutive models for sand
have been presented. Nevertheless, only some of them can satisfy this
mechanism. One of the most useful models in this term is
UBCSAND model. In this research, the capability of this model is
considered by using PLAXIS software. The real data of superstition
hills earthquake 1987 in the Imperial Valley was used. The results of
the simulation have shown resembling trend of the UBC3D-PLM
model.
Abstract: In this paper, the effect of width and height of the
model on the earthquake response in the finite element method is
discussed. For this purpose an earth dam as a soil structure under
earthquake has been considered. Various dam-foundation models are
analyzed by Plaxis, a finite element package for solving geotechnical
problems. The results indicate considerable differences in the seismic
responses.
Abstract: The motorway segment between Tangier and Oued
R’mel has experienced, since the beginning of building works,
significant instability and landslides linked to a number of geological,
hydrogeological and geothermic factors affecting the different
formations.
The landslides observed are not fully understood, despite many
studies conducted on this segment. This study aims at producing new
methods to better explain the phenomena behind the landslides,
taking into account the geotechnical and geothermic contexts. This
analysis builds up on previous studies and geotechnical data collected
in the field.
The final body of data collected shall be processed through the
Plaxis software for a better and customizable view of the landslide
problems in the area, which will help tofind solutions and stabilize
land in the area.
Abstract: When the foundations of structures under cyclic
loading with amplitudes less than their permissible load, the concern exists often for the amount of uniform and non-uniform settlement of
such structures. Storage tank foundations with numerous filling and discharging and railways ballast course under repeating
transportation loads are examples of such conditions. This paper
deals with the effects of using the new generation of reinforcements,
Grid-Anchor, for the purpose of reducing the permanent settlement
of these foundations under the influence of different proportions of
the ultimate load. Other items such as the type and the number of
reinforcements as well as the number of loading cycles are studied numerically. Numerical models were made using the Plaxis3D
Tunnel finite element code. The results show that by using gridanchor
and increasing the number of their layers in the same
proportion as that of the cyclic load being applied, the amount of
permanent settlement decreases up to 42% relative to unreinforced
condition depends on the number of reinforcement layers and percent
of applied load and the number of loading cycles to reach a constant
value of dimensionless settlement decreases up to 20% relative to
unreinforced condition.