Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: One problem of synthetic sunflower cultivation is an
erratic germination of the seeds. To improve the germination, presowing
seed treatment with an ultrasound was tested. All treatments
were carried out at 40 kHz frequency with the intensities of 40, 60,
80 and 100% of the ultrasonic generator total power (250 W) for the
durations of 5, 10, 15 and 20 minutes. Data on seed germination
percentage, seed vigor index (SVI), root and shoot lengths of
seedlings were collected. The results showed that germination, SVI,
root and shoot lengths of ultrasonic treated seedlings were different
from the control, depending on intensity of the ultrasound. The
effects of ultrasonic treatment were significant on germination,
resulting in a maximum increase of 43% at 40 and 60% intensities
compared to that of the control seeds. In addition, seedlings of these 2
treatments had higher SVI and longer root and shoot lengths than that
of the control seedlings. All treatment durations resulted in higher
germination and SVI, longer root and higher shoot lenghts of
seedlings than the control. Among the duration treatments, only SVI
and seedling root length were significantly different.
Abstract: The common bean is the most important grain legume for direct human consumption in the world and BCMV is one of the world's most serious bean diseases that can reduce yield and quality of harvested product. To determine the best tolerance index to BCMV and recognize tolerant genotypes, 2 experiments were conducted in field conditions. Twenty five common bean genotypes were sown in 2 separate RCB design with 3 replications under contamination and non-contamination conditions. On the basis of the results of indices correlations GMP, MP and HARM were determined as the most suitable tolerance indices. The results of principle components analysis indicated 2 first components totally explained 98.52% of variations among data. The first and second components were named potential yield and stress susceptible respectively. Based on the results of BCMV tolerance indices assessment and biplot analysis WA8563-4, WA8563-2 and Cardinal were the genotypes that exhibited potential seed yield under contamination and noncontamination conditions.
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.
Abstract: This research sought to discover the forms of
promotion and dissemination of traditional local wisdom that are
used to create occupations among the elderly at Noanmueng
Community, Muang Sub-District, Baan Doong District, Udornthani
Province. The criteria used to select the research sample group were:
having a role involved in the promotion and dissemination of
traditional local wisdom to create occupations among the elderly;
being an experienced person who the residents of Noanmueng
Community find trustworthy; and having lived in Noanmueng
Community for a long time so as to be able to see the development
and change that occurs. A total of 16 persons were thus selected. Data
was gathered through a qualitative study, using semi-structured indepth
interviews. The collected data was then summarized and
discussed according to the research objectives. Finally, the data was
presented in narrative format. Results found that the identifying
traditional local wisdom of the community (which grew from the
residents’ experience and beneficial usage in daily life, passed down
from generation to generation) was the weaving of cloth and
basketry. As for the manner of promotion and dissemination of
traditional local wisdom, these skills were passed down through
teaching by example to family members, relatives and others in the
community. This was largely the initiative of the elders or elderly
members of the community. In order for the promotion and
dissemination of traditional local wisdom to create occupations
among the elderly, the traditional local wisdom should be supported
in every way through participation of the community members. For
example, establish a museum of traditional local wisdom for the
collection of traditional local wisdom in various fields, both from the
past and present innovations. This would be a source of pride for the
community, simultaneously helping traditional local wisdom to
become widely known and to create income for the community’s
elderly. Additional ways include organizing exhibitions of products
made by traditional local wisdom, finding both domestic and
international markets, as well as building both domestic and
international networks aiming to find opportunities to market
products made by traditional local wisdom.
Abstract: Unified Modeling Language (UML) is a standard
language for modeling of a system. UML is used to visually specify
the structure and behavior of a system. The system requirements are
captured and then converted into UML specification. UML
specification uses a set of rules and notations, and diagrams to
specify the system requirements. In this paper, we present a tool for
developing the UML specification. The tool will ease the use of the
notations and diagrams for UML specification as well as increase the
understanding and familiarity of the UML specification. The tool will
also be able to check the conformance of the diagrams against each
other for basic compliance of UML specification.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC-s participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC-s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC-s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC-s consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC-s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: The microbiological and physicochemical
characteristics of wetland soils in Eket Local Government Area were
studied between May 2001 and June 2003. Total heterotrophic
bacterial counts (THBC), total fungal counts (TFC), and total
actinomycetes counts (TAC) were determined from soil samples
taken from four locations at two depths in the wet and dry seasons.
Microbial isolates were characterized and identified. Particle size and
chemical parameters were also determined using standard methods.
THBC ranged from 5.2 (+0.17) x106 to 1.7 (+0.18) x107 cfu/g and
from 2.4 (+0.02) x106 to 1.4 (+0.04) x107cfu/g in the wet and dry
seasons, respectively. TFC ranged from 1.8 (+0.03) x106 to 6.6 (+
0.18) x106 cfu/g and from 1.0 (+0.04) x106 to 4.2 (+ 0.01) x106 cfu/g
in the wet and dry seasons, respectively .TAC ranged from 1.2
(+0.53) x106 to 6.0 (+0.05) x106 cfu/g and from 0.6 (+0.01) x106 to
3.2 (+ 0.12) x106 cfu/g in the wet and dry season, respectively.
Acinetobacter, Alcaligenes, Arthrobacter, Bacillus, Beijerinckja,
Enterobacter, Micrococcus, Flavobacterium, Serratia, Enterococcus,
and Pseudomonas species were predominant bacteria while
Aspergillus, Fusarium, Mucor, Penicillium, and Rhizopus were the
dominant fungal genera isolated. Streptomyces and Norcadia were
the actinomycetes genera isolated. The particle size analysis showed
high sand fraction but low silt and clay. The pH and % organic
matter were generally acidic and low, respectively at all locations.
Calcium dominated the exchangeable bases with low electrical
conductivity and micronutrients. These results provide the baseline
data of Eket wetland soils for its management for sustainable
agriculture.
Abstract: Whilst there is growing evidence that activity
across the lifespan is beneficial for improved health, there are
also many changes involved with the aging process and
subsequently the potential for reduced indices of health. The
nexus between health, physical activity and aging is complex
and has raised much interest in recent times due to the
realization that a multifaceted approached is necessary in
order to counteract a growing obesity epidemic. By
investigating age based trends within a population adhering to
competitive sport at older ages, further insight might be
gleaned to assist in understanding one of many factors
influencing this relationship.
BMI was derived using data gathered on a total of 6,071
masters athletes (51.9% male, 48.1% female) aged 25 to 91
years ( =51.5, s =±9.7), competing at the Sydney World
Masters Games (2009). Using linear and loess regression it
was demonstrated that the usual tendency for prevalence of
higher BMI increasing with age was reversed in the sample.
This trend in reversal was repeated for both male and female
only sub-sets of the sample participants, indicating the
possibility of improved prevalence of BMI with increasing
age for both the sample as a whole and these individual subgroups.
This evidence of improved classification in one index of
health (reduced BMI) for masters athletes (when compared to
the general population) implies there are either improved
levels of this index of health with aging due to adherence to
sport or possibly the reduced BMI is advantageous and
contributes to this cohort adhering (or being attracted) to
masters sport at older ages. Demonstration of this
proportionately under-investigated World Masters Games
population having an improved relationship between BMI and
increasing age over the general population is of particular
interest in the context of the measures being taken globally to
curb an obesity epidemic.
Abstract: The present study presents a new approach to automatic
data clustering and classification problems in large and complex
databases and, at the same time, derives specific types of explicit rules
describing each cluster. The method works well in both sparse and
dense multidimensional data spaces. The members of the data space
can be of the same nature or represent different classes. A number
of N-dimensional ellipsoids are used for enclosing the data clouds.
Due to the geometry of an ellipsoid and its free rotation in space
the detection of clusters becomes very efficient. The method is based
on genetic algorithms that are used for the optimization of location,
orientation and geometric characteristics of the hyper-ellipsoids. The
proposed approach can serve as a basis for the development of
general knowledge systems for discovering hidden knowledge and
unexpected patterns and rules in various large databases.
Abstract: Market competition and a desire to gain advantages on globalized market, drives companies towards innovation efforts. Project overload is an unpleasant phenomenon, which is happening for employees inside those organizations trying to make the most efficient use of their resources to be innovative. But what are the impacts of project overload on organization-s innovation capabilities? Advanced engineering teams (AE) inside a major heavy equipment manufacturer are suffering from project overload in their quest for innovation. In this paper, Agent-based modeling (ABM) is used to examine the current reality of the company context, and of the AE team, where the opportunities and challenges for reducing the risk of project overload and moving towards innovation were identified. Project overload is more likely to stifle innovation and creativity inside teams. On the other hand, motivations on proper challenging goals are more likely to help individual to alleviate the negative aspects of low level of project overload.
Abstract: The paper presents a technique suitable in robot
vision applications where it is not possible to establish the object position from one view. Usually, one view pose calculation methods
are based on the correspondence of image features established at a
training step and exactly the same image features extracted at the
execution step, for a different object pose. When such a
correspondence is not feasible because of the lack of specific features
a new method is proposed. In the first step the method computes
from two views the 3D pose of feature points. Subsequently, using a
registration algorithm, the set of 3D feature points extracted at the execution phase is aligned with the set of 3D feature points extracted
at the training phase. The result is a Euclidean transform which have
to be used by robot head for reorientation at execution step.
Abstract: This paper presents a time control liquids mixing
system in the tanks as an application of fuzzy time control discrete
model. The system is designed for a wide range of industrial
applications. The simulation design of control system has three
inputs: volume, viscosity, and selection of product, along with the
three external control adjustments for the system calibration or to
take over the control of the system autonomously in local or
distributed environment. There are four controlling elements: rotatory
motor, grinding motor, heating and cooling units, and valves
selection, each with time frame limit. The system consists of three
controlled variables measurement through its sensing mechanism for
feed back control. This design also facilitates the liquids mixing
system to grind certain materials in tanks and mix with fluids under
required temperature controlled environment to achieve certain
viscous level. Design of: fuzzifier, inference engine, rule base,
deffuzifiers, and discrete event control system, is discussed. Time
control fuzzy rules are formulated, applied and tested using
MATLAB simulation for the system.
Abstract: Installation of power compensation equipment in
some cases places additional buses into the system. Therefore, a total
number of power flow equations and voltage unknowns increase due
to additional locations of installed devices. In this circumstance, power flow calculation is more complicated. It may result in a
computational convergence problem. This paper presents a power flow calculation by using Newton-Raphson iterative method together
with the proposed load transfer technique. This concept is to eliminate additional buses by transferring installed loads at the new buses to existing two adjacent buses. Thus, the total number of power
flow equations is not changed. The overall computational speed is
expectedly shorter than that of solving the problem without applying the load transfer technique. A 15-bus test system is employed for test
to evaluate the effectiveness of the proposed load transfer technique. As a result, the total number of iteration required and execution time
is significantly reduced.
Abstract: Petrology and geochemical characteristics of granitic
rocks from South Sulawesi, especially from Polewaliand Masamba
area are presented in order to elucidate their origin of magma and
geodynamic setting. The granitic rocks in these areas are dominated by
granodiorite and granite in composition. Quartz, K-feldspar and
plagioclase occur as major phases with hornblende and biotite as
major ferromagnesian minerals. All of the samples were plotted in
calc-alkaline field, show metaluminous affinity and typical of I-type
granitic rock. Harker diagram indicates that granitic rocks experienced
fractional crystallization during magmatic evolution. Both groups
displayed an extreme enrichment of LILE, LREE and a slight negative
Eu anomaly which resemble upper continental crust affinity. They
were produced from partial melting of upper continental crust and
have close relationship of sources composition within a suite. The
geochemical characteristics explained the arc related subduction
environment which later give an evidence of continent-continent
collision between Australia-derived microcontinent and Sundalandto
form continental arc environment.
Abstract: The ultimate goal of this article is to develop a robust and accurate numerical method for solving hyperbolic conservation laws in one and two dimensions. A hybrid numerical method, coupling a cheap fourth order total variation diminishing (TVD) scheme [1] for smooth region and a Robust seventh-order weighted non-oscillatory (WENO) scheme [2] near discontinuities, is considered. High order multi-resolution analysis is used to detect the high gradients regions of the numerical solution in order to capture the shocks with the WENO scheme, while the smooth regions are computed with fourth order total variation diminishing (TVD). For time integration, we use the third order TVD Runge-Kutta scheme. The accuracy of the resulting hybrid high order scheme is comparable with these of WENO, but with significant decrease of the CPU cost. Numerical demonstrates that the proposed scheme is comparable to the high order WENO scheme and superior to the fourth order TVD scheme. Our scheme has the added advantage of simplicity and computational efficiency. Numerical tests are presented which show the robustness and effectiveness of the proposed scheme.
Abstract: The study investigated the 2011 TPGA Ever Rich
Championship – North Bay Open spectators- on-the-site spectating
motivations, experiences, and satisfactions. The research was
conducted on a convenience sample of the on-the-spot spectators at the
North Bay Golf and Country Club. A total of 200 questionnaires were
distributed, of which 185 valid questionnaires were collected,
approaching a 92.5% response rate. The data obtained was analyzed
with statistical techniques. First, the data showed significant
differences in motivations, experiences, and satisfactions relative to
demographic variables among the on-the-spot spectators. Second,
spectating motivation, experience, and satisfaction were significantly
related to one another.
Abstract: In this paper is study the possibility of successfully
implementing of hollow roller concept in order to minimize inertial
mass of the large bearings, with major results in diminution of the
material consumption, increasing of power efficiency (in wind power
station area), increasing of the durability and life duration of the large
bearings systems, noise reduction in working, resistance to
vibrations, an important diminution of losses by abrasion and
reduction of the working temperature. In this purpose was developed
an original solution through which are reduced mass, inertial forces
and moments of large bearings by using of hollow rollers. The
research was made by using the method of finite element analysis
applied on software type Solidworks - Nastran. Also, is study the
possibility of rapidly changing the manufacturing system of solid and
hollow cylindrical rollers.
Abstract: New exact three-wave solutions including periodic two-solitary solutions and doubly periodic solitary solutions for the (2+1)-dimensional asymmetric Nizhnik-Novikov- Veselov (ANNV) system are obtained using Hirota's bilinear form and generalized three-wave type of ansatz approach. It is shown that the generalized three-wave method, with the help of symbolic computation, provides an e¤ective and powerful mathematical tool for solving high dimensional nonlinear evolution equations in mathematical physics.