Abstract: Nanoscale thermites such as the composite mixture of
nano-sized aluminum and molybdenum trioxide powders possess
several technical advantages such as much higher reaction rate and
shorter ignition delay, when compared to the conventional energetic
formulations made of micron-sized metal and oxidizer particles. In this
study, the self-propagation of combustion wave in compacted pellets
of nanoscale thermite composites is modeled and computationally
investigated by utilizing the activation energy reduction of aluminum
particles due to nanoscale particle sizes. The present computational
model predicts the speed of combustion wave propagation which is
good agreement with the corresponding experiments of thermite
reaction. Also, several characteristics of thermite reaction in nanoscale
composites are discussed including the ignition delay and combustion
wave structures.
Abstract: Australia is a country of some 7,700 million square kilometers with a population of about 22.6 million. At present water security is a major challenge for Australia. In some areas the use of water resources is approaching and in some parts it is exceeding the limits of sustainability. A focal point of proposed national water conservation programs is the recycling of both urban stormwater and treated wastewater. But till now it is not widely practiced in Australia, and particularly stormwater is neglected. In Australia, only 4% of stormwater and rainwater is recycled, whereas less than 1% of reclaimed wastewater is reused within urban areas. Therefore, accurately monitoring, assessing and predicting the availability, quality and use of this precious resource are required for better management. As stormwater is usually of better quality than untreated sewage or industrial discharge, it has better public acceptance for recycling and reuse, particularly for non-potable use such as irrigation, watering lawns, gardens, etc. Existing stormwater recycling practice is far behind of research and no robust technologies developed for this purpose. Therefore, there is a clear need for using modern technologies for assessing feasibility of stormwater harvesting and reuse. Numerical modeling has, in recent times, become a popular tool for doing this job. It includes complex hydrological and hydraulic processes of the study area. The hydrologic model computes stormwater quantity to design the system components, and the hydraulic model helps to route the flow through stormwater infrastructures. Nowadays water quality module is incorporated with these models. Integration of Geographic Information System (GIS) with these models provides extra advantage of managing spatial information. However for the overall management of a stormwater harvesting project, Decision Support System (DSS) plays an important role incorporating database with model and GIS for the proper management of temporal information. Additionally DSS includes evaluation tools and Graphical user interface. This research aims to critically review and discuss all the aspects of stormwater harvesting and reuse such as available guidelines of stormwater harvesting and reuse, public acceptance of water reuse, the scopes and recommendation for future studies. In addition to these, this paper identifies, understand and address the importance of modern technologies capable of proper management of stormwater harvesting and reuse.
Abstract: Since, both the relative position of tunnels and the construction procedure affect the soil movement and internal forces in the lining, it is of major concern to study the influence of these factors on the tunnel design. Construction procedures of tunnels have considerable effects on the magnitude of surface movements and lining stresses. This paper describes numerical analysis of construction procedure of a three adjacent shallow tunnels at high groundwater levels using the commercial finite difference software (FLAC-3D). The aim of this study is to determinate the most suitable construction procedure for the three tunnels and the optimum excavation step in Tehran Metro tunnels in order to optimize the surface settlements and lining stresses.
Abstract: Resistance spot welding (RSW) has been used widely to join sheet metals. It has been a challenge to get required weld quality in spot welding of dissimilar thickness materials. Weld parameters are not generally available in standards for thickness beyond 4mm. This paper presents the welding process design and parameter optimization of RSW used in joining of low carbon steel sheet of thickness 0.8 mm and metal strips of cross section 10 x 5mm for electrical motor applications. Taguchi quality design was adopted for weld current and time optimization using L9 orthogonal array. Optimum process parameters (current- 3.5kA and time- 10 cycles) were obtained from the Taguchi analysis and shear test results. Confirmation experiment result revealed that the weld quality was within acceptable interval. Further, numerical simulation of RSW process was carried out with selected weld parameters to quantify the temperature at faying surface and check for formation of appropriate nugget. The nugget geometry measured after peel test and predicted from numerical validation method were similar and in accordance with the standards.
Abstract: One of the Best Management Practices (BMPs) promoted in Urban Stormwater Management Manual for Malaysia (MSMA) published by the Department of Irrigation and Drainage (DID) in 2001 is through the construction of wet ponds in new development projects for water quantity and quality control. Therefore, this paper aims to demonstrate a case study on evaluation of a constructed mini wet pond located at Sekolah Rendah Kebangsaan Seksyen 2, Puchong, Selangor, Malaysia in both stormwater quantity and quality aspect particularly to reduce the peak discharge by temporary storing and gradual release of stormwater runoff from an outlet structure or other release mechanism. The evaluation technique will be using InfoWorks Collection System (CS) as the numerical modeling approach for water quantity aspect. Statistical test by comparing the correlation coefficient (R2), mean error (ME), mean absolute error (MAE) and root mean square error (RMSE) were used to evaluate the model in simulating the peak discharge changes. Results demonstrated that there will be a reduction in peak flow at 11 % to 15% and time to peak flow is slower by 5 minutes through a wet pond. For water quality aspect, a survey on biological indicator of water quality carried out depicts that the pond is within the range of rather clean to clean water with the score of 5.3. This study indicates that a constructed wet pond with wetland facilities is able to help in managing water quantity and stormwater generated pollution at source, towards achieving ecologically sustainable development in urban areas.
Abstract: The paper aims at evaluating the effects of heavy groundwater withdrawal and artificial groundwater recharge of an ex-mining pond to the aquifer system of the Langat Basin through the three-dimensional (3D) numerical modeling. Many mining sites have been left behind from the massive mining exploitations in Malaysia during the England colonization era and from the last few decades. These sites are able to accommodate more than a million cubic meters of water from precipitation, runoff, groundwater, and river. Most of the time, the mining sites are turned into ponds for recreational activities. In the current study, an artificial groundwater recharge from an ex-mining pond in the Langat Basin was proposed due to its capacity to store >50 million m3 of water. The location of the pond is near the Langat River and opposite a steel company where >4 million gallons of groundwater is withdrawn on a daily basis. The 3D numerical simulation was developed using the Groundwater Modeling System (GMS). The calibrated model (error about 0.7 m) was utilized to simulate two scenarios (1) Case 1: artificial recharge pond with no pumping and (2) Case 2: artificial pond with pumping. The results showed that in Case 1, the pond played a very important role in supplying additional water to the aquifer and river. About 90,916 m3/d of water from the pond, 1,173 m3/d from the Langat River, and 67,424 m3/d from the direct recharge of precipitation infiltrated into the aquifer system. In Case 2, due to the abstraction of groundwater from a company, it caused a steep depression around the wells, river, and pond. The result of the water budget showed an increase rate of inflow in the pond and river with 92,493m3/d and 3,881m3/d respectively. The outcome of the current study provides useful information of the aquifer behavior of the Langat Basin.
Abstract: Mechanical properties of cerebral arteries are, due to their relationship with cerebrovascular diseases, of clinical worth. To acquire these properties, eight samples were obtained from middle cerebral arteries of human cadavers, whose death were not due to injuries or diseases of cerebral vessels, and tested within twelve hours after resection, by a precise biaxial tensile test device specially developed for the present study considering the dimensions, sensitivity and anisotropic nature of samples. The resulting stress-stretch curve was plotted and subsequently fitted to a hyperelastic three-parameter Fung model. It was found that the arteries were noticeably stiffer in circumferential than in axial direction. It was also demonstrated that the use of multi-parameter hyperelastic constitutive models is useful for mathematical description of behavior of cerebral vessel tissue. The reported material properties are a proper reference for numerical modeling of cerebral arteries and computational analysis of healthy or diseased intracranial arteries.
Abstract: The subject of this paper is to verify the behavior of the truss-type CHS joint which is beyond the scope of use of the EN 1993-1-8. This is performed by using the numerical modeling in program ANSYS and the analytical methods recommended in the CIDECT publication. The recommendations for numerical modeling of such types of joints as well as for evaluation of load-bearing capacity of the joint are given in this paper. The results from both analytical and numerical models are compared.
Abstract: An important aspect of planning for shallow tunneling under urban areas is the determination of likely surface movements and interaction with existing structures. Back analysis of built tunnels that their settlements magnitude is available, could aid the designers to have a more accuracy in future projects.
In this paper, one single Tehran Metro Tunnel (at west of Hor square, Jang University Street) was selected. At first, surface settlements of this tunnel were measured in situ. Then this tunnel was modeled using the commercial finite deference software FLAC-3D. Finally, Results of modeling and in situ measurements compared for verification.
Abstract: Worldwide interests for the renewable energy are increasing due to environmental and climate changes from traditional petroleum related energy sources. To account for these social needs, ligneous biomass energy is considered as one of the environmentally friend energy solutions. The wood torrefaction process is a feasible method to improve the properties of the biomass fuel and makes the wood have low moisture, lower smoke emission and increased heating value. In this work, therefore, the moisture evaporation model which largely affects energy efficiency of ligneous biomass through moisture contents and heating value relative to its weight is studied with numerical modeling approach by analyzing the effects of torrefaction furnace temperature. The results show that the temperature and moisture fraction of wood decrease by increasing the furnace temperature. When the torrefaction temperature is lower than 423K, there were little changes of the moisture fraction in the wood. Also, it can be found that charcoal is produced more slowly when the torrefaction temperature is lower than 573K.
Abstract: In all industries which are related to heat, suitable
thermal ranges are defined for each device to operate well.
Consideration of these limits requires a thermal control unit beside
the main system. The Satellite Thermal Control Unit exploits from
different methods and facilities individually or mixed. For enhancing
heat transfer between primary surface and the environment,
utilization of radiating extended surfaces are common. Especially for
large temperature differences; variable thermal conductivity has a
strong effect on performance of such a surface .In most literatures,
thermo-physical properties, such as thermal conductivity, are
assumed as constant. However, in some recent researches the
variation of these parameters is considered. This may be helpful for
the evaluation of fin-s temperature distribution in relatively large
temperature differences. A new method is introduced to evaluate
temperature-dependent thermal conductivity values. The finite
volume method is employed to simulate numerically the temperature
distribution in a space radiating fin. The present modeling is carried
out for Aluminum as fin material and compared with previous
method. The present results are also compared with those of two
other analytical methods and good agreement is shown.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: In this article, biomechanical aspects of hen-s eggshell as a natural ceramic structure are studied. The images, taken by a scanning electron microscope (SEM), are used to investigate the microscopic aspects of the egg. It is observed that eggshell has a three-layered microstructure with different morphological and structural characteristics. Studies on the eggshell membrane (ESM) as a prosperous tissue suggest that it is placed to prevent the penetration of microorganisms into the egg. Finally, numerical models of the egg are presented to study the stress distribution and its deformation under different loading conditions. The effects of two different types of loading (hydrostatic and point loadings) on two different shell models (with constant and variable thicknesses) are investigated in detail.
Abstract: Channel junctions can be analyzed in two ways of
division (lateral intake) and combined flows (confluence). The
present paper investigates 3D flow pattern at lateral intake using
Navier-Stokes equation and κ -ε (RNG) turbulent model. The
equations are solved by Finite-Volume Method (FVM) and results
are compared with the experimental data of (Barkdoll, B.D., 1997)
to test the validity of the findings. Comparison of the results with
the experimental data indicated a close proximity between the two
sets of data which suggest a very close simulation. Results further
indicated an inverse relation between the effects of discharge ratio
( r Q ) on the length and width of the separation zone. In other words,
as the discharge ration increases, the length and width of separation
zone decreases.
Abstract: The interaction of tunneling or mining with
groundwater has become a very relevant problem not only due to the
need to guarantee the safety of workers and to assure the efficiency of
the tunnel drainage systems, but also to safeguard water resources
from impoverishment and pollution risk. Therefore it is very
important to forecast the drainage processes (i.e., the evaluation of
drained discharge and drawdown caused by the excavation). The aim
of this study was to know better the system and to quantify the flow
drained from the Fontane mines, located in Val Germanasca (Turin,
Italy). This allowed to understand the hydrogeological local changes
in time. The work has therefore been structured as follows: the
reconstruction of the conceptual model with the geological,
hydrogeological and geological-structural study; the calculation of
the tunnel inflows (through the use of structural methods) and the
comparison with the measured flow rates; the water balance at the
basin scale. In this way it was possible to understand what are the
relationships between rainfall, groundwater level variations and the
effect of the presence of tunnels as a means of draining water.
Subsequently, it the effects produced by the excavation of the mining
tunnels was quantified, through numerical modeling. In particular,
the modeling made it possible to observe the drawdown variation as a
function of number, excavation depth and different mines linings.
Abstract: According to the European laws, there is the
possibility of reusing the washing wastes for the environmental
requalification of quarry lakes. The paper deals with the
hydrogeological aspects involved in this possibility, as the
introduction of finest wastes in the quarry lakes can generate
alterations of the hydrogeological setting of the area, and problems
for the future accessibility of the zone. To evaluate the
hydrogeological compatibility of the washing wastes reuse in quarry
lakes a groundwater numerical model was carried out, pointing out
both the hydrogeological feasibility of this intervention and some
guide lines for its optimization, in terms of inflow point with regard
the groundwater flow direction and loss of volume in the quarry lake.