Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: Extensive wind tunnel tests have been conducted to
investigate the unsteady flow field over and behind a 2D model of a
660 kW wind turbine blade section in pitching motion. The surface
pressure and wake dynamic pressure variation at a distance of 1.5
chord length from trailing edge were measured by pressure
transducers during several oscillating cycles at 3 reduced frequencies
and oscillating amplitudes. Moreover, form drag and linear
momentum deficit are extracted and compared at various conditions.
The results show that the wake velocity field and surface pressure of
the model have similar behavior before and after the airfoil beyond
the static stall angle of attack. In addition, the effects of reduced
frequency and oscillation amplitudes are discussed.
Abstract: The paper investigates downtrend algorithm and
trading strategy based on chart pattern recognition and technical
analysis in futures market. The proposed chart formation is a pattern
with the lowest low in the middle and one higher low on each side.
The contribution of this paper lies in the reinforcement of statements
about the profitability of momentum trend trading strategies.
Practical benefit of the research is a trading algorithm in falling
markets and back-test analysis in futures markets. When based on
daily data, the algorithm has generated positive results, especially
when the market had downtrend period. Downtrend algorithm can be
applied as a hedge strategy against possible sudden market crashes.
The proposed strategy can be interesting for futures traders, hedge
funds or scientific researchers performing technical or algorithmic
market analysis based on momentum trend trading.
Abstract: The significant effects of the interactions between the
system boundaries and the near wall molecules in miniaturized
gaseous devices lead to the formation of the Knudsen layer in which
the Navier-Stokes-Fourier (NSF) equations fail to predict the correct
associated phenomena. In this paper, the well-known lattice
Boltzmann method (LBM) is employed to simulate the fluid flow and
heat transfer processes in rarefied gaseous micro media. Persuaded
by the problematic deficiency of the LBM in capturing the Knudsen
layer phenomena, present study tends to concentrate on the effective
molecular mean free path concept the main essence of which is to
compensate the incapability of this mesoscopic method in dealing
with the momentum and energy transport within the above mentioned
kinetic boundary layer. The results show qualitative and quantitative
accuracy comparable to the solutions of the linearized Boltzmann
equation or the DSMC data for the Knudsen numbers of O (1) .
Abstract: Elementary particles are created in pairs of equal and opposite momentums at a reference frame at the speed of light. The speed of light reference frame is viewed as a point in space as observed by observer at rest. This point in space is the bang location of the big bang theory. The bang in the big bang theory is not more than sustained flow of pairs of positive and negative elementary particles. Electrons and negative charged elementary particles are ejected from this point in space at velocities faster than light, while protons and positively charged particles obtain velocities lower than light. Subsonic masses are found to have real and positive charge, while supersonic masses are found to be negative and imaginary indicating that the two masses are of different entities. The electron-s super-sonic speed, as viewed by rest observer was calculated and found to be less than the speed of light and is little higher than the electron speed in Bohr-s orbit. The newly formed hydrogen gas temperature was found to be in agreement with temperatures found on newly formed stars. Universe expansion was found to be in agreement. Partial mass and charge elementary particles and particles with momentum only were explained in the context of this theoretical approach.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: The forced convection heat transfer in high porosity metal-foam filled tube heat exchangers are studied in this paper. The Brinkman Darcy momentum model and two energy equations for both solid and fluid phases in porous media are employed .The study shows that using metal-foams can significantly improve the heat transfer in heat exchangers.
Abstract: In this research, a 2-D computational analysis of
steady state free convection in a rectangular enclosure filled with an
electrically conducting fluid under Effect of Magnetic Field has been
performed. The governing equations (mass, momentum, and energy)
are formulated and solved by a finite volume method (FVM)
subjected to different boundary conditions. A parametric study has
been conducted to consider the influence of Grashof number (Gr),
Prantdl number (Pr) and the orientation of magnetic field on the flow
and heat transfer characteristics. It is observed that Nusselt number
(Nu) and heat flux will increase with increasing Grashof and Prandtl
numbers and decreasing the slope of the orientation of magnetic field.
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: This paper presents performance analysis of the
Evolutionary Programming-Artificial Neural Network (EPANN)
based technique to optimize the architecture and training parameters
of a one-hidden layer feedforward ANN model for the prediction of
energy output from a grid connected photovoltaic system. The ANN
utilizes solar radiation and ambient temperature as its inputs while the
output is the total watt-hour energy produced from the grid-connected
PV system. EP is used to optimize the regression performance of the
ANN model by determining the optimum values for the number of
nodes in the hidden layer as well as the optimal momentum rate and
learning rate for the training. The EPANN model is tested using two
types of transfer function for the hidden layer, namely the tangent
sigmoid and logarithmic sigmoid. The best transfer function, neural
topology and learning parameters were selected based on the highest
regression performance obtained during the ANN training and testing
process. It is observed that the best transfer function configuration for
the prediction model is [logarithmic sigmoid, purely linear].
Abstract: In this paper, a two-dimensional (2D) numerical
model for the tidal currents simulation in Persian Gulf is presented.
The model is based on the depth averaged equations of shallow water
which consider hydrostatic pressure distribution. The continuity
equation and two momentum equations including the effects of bed
friction, the Coriolis effects and wind stress have been solved. To
integrate the 2D equations, the Alternative Direction Implicit (ADI)
technique has been used. The base of equations discritization was
finite volume method applied on rectangular mesh. To evaluate the
model validation, a dam break case study including analytical
solution is selected and the comparison is done. After that, the
capability of the model in simulation of tidal current in a real field is
represented by modeling the current behavior in Persian Gulf. The
tidal fluctuations in Hormuz Strait have caused the tidal currents in
the area of study. Therefore, the water surface oscillations data at
Hengam Island on Hormoz Strait are used as the model input data.
The check point of the model is measured water surface elevations at
Assaluye port. The comparison between the results and the
acceptable agreement of them showed the model ability for modeling
marine hydrodynamic.
Abstract: In this article, a simulation method called the Homotopy Perturbation Method (HPM) is employed in the steady flow of a Walter's B' fluid in a vertical channel with porous wall. We employed Homotopy Perturbation Method to derive solution of a nonlinear form of equation obtained from exerting similarity transforming to the ordinary differential equation gained from continuity and momentum equations of this kind of flow. The results obtained from the Homotopy Perturbation Method are then compared with those from the Runge–Kutta method in order to verify the accuracy of the proposed method. The results show that the Homotopy Perturbation Method can achieve good results in predicting the solution of such problems. Ultimately we use this solution to obtain the other terms of velocities and physical discussion about it.
Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: In the paper, the energetic features of the loaded gait
are newly analyzed depending on the trunk flexion change. To
investigate the loaded gait, walking experiments are performed for five
subjects and, the ground reaction forces and kinematic data are
measured. Based on these information, we compute the impulse,
momentum and mechanical works done on the center of body mass,
through the trunk flexion change. As a result, it is shown that the trunk
flexion change does not affect the impulses and momentums during
the step-to-step transition as well. However, the direction of the
pre-collision momentum does change depending on the trunk flexion
change, which is degenerated just after (or during) the collision period.
Abstract: In this paper, a comparative study of application of
supervised and unsupervised learning algorithms on illumination
invariant face recognition has been carried out. The supervised
learning has been carried out with the help of using a bi-layered
artificial neural network having one input, two hidden and one output
layer. The gradient descent with momentum and adaptive learning
rate back propagation learning algorithm has been used to implement
the supervised learning in a way that both the inputs and
corresponding outputs are provided at the time of training the
network, thus here is an inherent clustering and optimized learning of
weights which provide us with efficient results.. The unsupervised
learning has been implemented with the help of a modified
Counterpropagation network. The Counterpropagation network
involves the process of clustering followed by application of Outstar
rule to obtain the recognized face. The face recognition system has
been developed for recognizing faces which have varying
illumination intensities, where the database images vary in lighting
with respect to angle of illumination with horizontal and vertical
planes. The supervised and unsupervised learning algorithms have
been implemented and have been tested exhaustively, with and
without application of histogram equalization to get efficient results.
Abstract: Vibration characteristics of subcooled flow boiling on
thin and long structures such as a heating rod were recently
investigated by the author. The results show that the intensity of the
subcooled boiling-induced vibration (SBIV) was influenced strongly
by the conditions of the subcooling temperature, linear power density
and flow velocity. Implosive bubble formation and collapse are the
main nature of subcooled boiling, and their behaviors are the only
sources to originate from SBIV. Therefore, in order to explain the
phenomenon of SBIV, it is essential to obtain reliable information
about bubble behavior in subcooled boiling conditions. This was
investigated at different conditions of coolant subcooling
temperatures of 25 to 75°C, coolant flow velocities of 0.16 to
0.53m/s, and linear power densities of 100 to 600 W/cm. High speed
photography at 13,500 frames per second was performed at these
conditions. The results show that even at the highest subcooling
condition, the absolute majority of bubbles collapse very close to the
surface after detaching from the heating surface. Based on these
observations, a simple model of surface tension and momentum
change is introduced to offer a rough quantitative estimate of the
force exerted on the heating surface during the bubble ebullition. The
formation of a typical bubble in subcooled boiling is predicted to
exert an excitation force in the order of 10-4 N.
Abstract: The objective of this paper is to develop a neural
network-based residual generator to detect the fault in the actuators
for a specific communication satellite in its attitude control system
(ACS). First, a dynamic multilayer perceptron network with dynamic
neurons is used, those neurons correspond a second order linear
Infinite Impulse Response (IIR) filter and a nonlinear activation
function with adjustable parameters. Second, the parameters from the
network are adjusted to minimize a performance index specified by
the output estimated error, with the given input-output data collected
from the specific ACS. Then, the proposed dynamic neural network
is trained and applied for detecting the faults injected to the wheel,
which is the main actuator in the normal mode for the communication
satellite. Then the performance and capabilities of the proposed
network were tested and compared with a conventional model-based
observer residual, showing the differences between these two
methods, and indicating the benefit of the proposed algorithm to
know the real status of the momentum wheel. Finally, the application
of the methods in a satellite ground station is discussed.
Abstract: Well-developed strategic marketing planning is the essential
prerequisite for establishment of the right and unique competitive
advantage. Typical market, however, is a heterogeneous
and decentralized structure with natural involvement of individual
or group subjectivity and irrationality. These features cannot be
fully expressed with one-shot rigorous formal models based on,
e.g. mathematics, statistics or empirical formulas. We present an
innovative solution, extending the domain of agent based computational
economics towards the concept of hybrid modeling in service
provider and consumer market such as telecommunications. The
behavior of the market is described by two classes of agents -
consumer and service provider agents - whose internal dynamics
are fundamentally different. Customers are rather free multi-state
structures, adjusting behavior and preferences quickly in accordance
with time and changing environment. Producers, on the contrary,
are traditionally structured companies with comparable internal processes
and specific managerial policies. Their business momentum is
higher and immediate reaction possibilities limited. This limitation
underlines importance of proper strategic planning as the main
process advising managers in time whether to continue with more
or less the same business or whether to consider the need for future
structural changes that would ensure retention of existing customers
or acquisition of new ones.