Abstract: This paper deals with the performance of semi-light weight concrete, prepared by using wood ash pellets as coarse aggregates which were improved by partial replacement of cement with alccofine. Alccofine is a mineral admixture which contains high glass content obtained through the process of controlled granulation. This is finer than cement which carries its own pozzolanic property. Therefore, cement could be replaced by alccofine as 0%, 5%, 10%, 15%, 20%, 25%, 30%, 35%, 40%, 45%, 50%, 55%, 60%, 65%, and 70% to enhance the strength and durability properties of concrete. High range water reducing admixtures (HRWA) were used in these mixes which were dosed up to 1.5% weight of the total cementitious content (alccofine & cement). It also develops the weaker transition zone into more impermeable layer. Specimens were subjected in both the accelerated curing method as well as conventional curing method. Experimental results were compared and reported, in that the maximum compressive strength of 32.6 MPa was achieved on 28th day with 30% replacement level in a density of 2200 kg/m3 to a conventional curing, while in the accelerated curing, maximum compressive strength was achieved at 40% replacement level. Rapid chloride penetration test (RCPT) output results for the conventional curing method at 0% and 70% give 3296.7 and 545.6 coulombs.
Abstract: In general, issues related to design and maintenance are considered in an independent manner. However, the decisions made in these two sets influence each other. The design for maintenance is considered an opportunity to optimize the life cycle cost of a product, particularly in the nuclear or aeronautical field, where maintenance expenses represent more than 60% of life cycle costs. The design of large-scale systems starts with product architecture, a choice of components in terms of cost, reliability, weight and other attributes, corresponding to the specifications. On the other hand, the design must take into account maintenance by improving, in particular, real-time monitoring of equipment through the integration of new technologies such as connected sensors and intelligent actuators. We noticed that different approaches used in the Design For Maintenance (DFM) methods are limited to the simultaneous characterization of the reliability and maintainability of a multi-component system. This article proposes a method of DFM that assists designers to propose dynamic maintenance for multi-component industrial systems. The term "dynamic" refers to the ability to integrate available monitoring data to adapt the maintenance decision in real time. The goal is to maximize the availability of the system at a given life cycle cost. This paper presents an approach for simultaneous optimization of the design and maintenance of multi-component systems. Here the design is characterized by four decision variables for each component (reliability level, maintainability level, redundancy level, and level of monitoring data). The maintenance is characterized by two decision variables (the dates of the maintenance stops and the maintenance operations to be performed on the system during these stops). The DFM model helps the designers choose technical solutions for the large-scale industrial products. Large-scale refers to the complex multi-component industrial systems and long life-cycle, such as trains, aircraft, etc. The method is based on a two-level hybrid algorithm for simultaneous optimization of design and maintenance, using genetic algorithms. The first level is to select a design solution for a given system that considers the life cycle cost and the reliability. The second level consists of determining a dynamic and optimal maintenance plan to be deployed for a design solution. This level is based on the Maintenance Free Operating Period (MFOP) concept, which takes into account the decision criteria such as, total reliability, maintenance cost and maintenance time. Depending on the life cycle duration, the desired availability, and the desired business model (sales or rental), this tool provides visibility of overall costs and optimal product architecture.
Abstract: The concept of urban metabolism has increasingly been employed in a diverse range of disciplines as a mean to analyze and theorize the city. Urban ecology has a particular focus on the implications of applying the metabolism concept to the urban realm. This approach has been developed by a few researchers, though it has rarely if ever been used in policy development for city planning. The aim of this research is to use ecologically informed urban planning interventions to increase the sustainability of urban metabolism; with special focus on land stock as a most important city resource by developing a system dynamic based DSS. This model identifies two critical management strategy variables for the Strategic Urban Plan Alexandria SUP 2032. As a result, this comprehensive and precise quantitative approach is needed to monitor, measure, evaluate and observe dynamic urban changes working as a decision support system (DSS) for policy making.
Abstract: With the rapid development of subsea oil and gas exploitation, the demand for the related underwater process equipment is increasing fast. In order to reduce the energy consuming, people tend to separate the gas and oil phase directly on the seabed. Accordingly, an advanced separator is needed. In this paper, the pressure drop of a new type of separator named Gas Liquid Cylindrical Cyclone (GLCC) which is used in the subsea system is investigated by both experiments and numerical simulation. In the experiments, the single phase flow and gas-liquid two phase flow in GLCC were tested. For the simulation, the performance of GLCC under both laboratory and industrial conditions was calculated. The Eulerian model was implemented to describe the mixture flow field in the GLCC under experimental conditions and industrial oil-natural gas conditions. Furthermore, a relationship among Euler number (Eu), Reynolds number (Re), and Froude number (Fr) is generated according to similarity analysis and simulation data, which can present the GLCC separation performance of pressure drop. These results can give reference to the design and application of GLCC in deep sea.
Abstract: Magnetic Resonance Imaging (MRI) is one of the
most important medical imaging modality. Subjective assessment of
the image quality is regarded as the gold standard to evaluate MR
images. In this study, a database of 210 MR images which contains
ten reference images and 200 distorted images is presented. The
reference images were distorted with four types of distortions: Rician
Noise, Gaussian White Noise, Gaussian Blur and DCT compression.
The 210 images were assessed by ten subjects. The subjective scores
were presented in Difference Mean Opinion Score (DMOS). The
DMOS values were compared with four FR-IQA metrics. We have
used Pearson Linear Coefficient (PLCC) and Spearman Rank Order
Correlation Coefficient (SROCC) to validate the DMOS values. The
high correlation values of PLCC and SROCC shows that the DMOS
values are close to the objective FR-IQA metrics.
Abstract: An innovative concept called “Flexy-Energy” is developing at 2iE. This concept aims to produce electricity at lower cost by smartly mix different available energy sources in accordance to the load profile of the region. With a higher solar irradiation and due to the fact that Diesel generator are massively used in sub-Saharan rural areas, PV/Diesel hybrid systems could be a good application of this concept and a good solution to electrify this region, provided they are reliable, cost effective and economically attractive to investors. Presentation of the developed approach is the aims of this paper. The PV/Diesel hybrid system designed consists to produce electricity and/or heat from a coupling between Diesel Diesel generators and PV panels without batteries storage, while ensuring the substitution of gasoil by bio-fuels available in the area where the system will be installed. The optimal design of this system is based on his technical performances; the Life Cycle Cost (LCC) and Levelized Cost of Energy are developed and use as economic criteria. The Net Present Value (NPV), the internal rate of return (IRR) and the discounted payback (DPB) are also evaluated according to dual electricity pricing (in sunny and unsunny hours). The PV/Diesel hybrid system obtained is compared to the standalone Diesel Diesel generators. The approach carried out in this paper has been applied to Siby village in Mali (Latitude 12 ° 23'N 8 ° 20'W) with 295 kWh as daily demand.This approach provides optimal physical characteristics (size of the components, number of component) and dynamical characteristics in real time (number of Diesel generator on, their load rate, fuel specific consumptions, and PV penetration rate) of the system. The system obtained is slightly cost effective; but could be improved with optimized tariffing strategies.
Abstract: Life Cycle Cost (LCC) is one of the goals and key
pillars of the construction management science because it comprises
many of the functions and processes necessary, which assist
organisations and agencies to achieve their goals. It has therefore
become important to design and control assets during their whole life
cycle, from the design and planning phase through to disposal phase.
LCCA is aimed to improve the decision making system in the
ownership of assets by taking into account all the cost elements
including to the asset throughout its life.
Current application of LCC approach is impractical during
misunderstanding of the advantages of LCC. This main objective of
this research is to show a different relationship between capital cost
and long-term running costs. One hundred and thirty eight actual
building projects in United Kingdom (UK) were used in order to
achieve and measure the above-mentioned objective of the study. The
result shown that LCC is one of the most significant tools should be
considered on the decision making process.
Abstract: Design for cost (DFC) is a method that reduces life
cycle cost (LCC) from the angle of designers. Multiple domain
features mapping (MDFM) methodology was given in DFC. Using
MDFM, we can use design features to estimate the LCC. From the
angle of DFC, the design features of family cars were obtained, such
as all dimensions, engine power and emission volume. At the
conceptual design stage, cars- LCC were estimated using back
propagation (BP) artificial neural networks (ANN) method and
case-based reasoning (CBR). Hamming space was used to measure the
similarity among cases in CBR method. Levenberg-Marquardt (LM)
algorithm and genetic algorithm (GA) were used in ANN. The
differences of LCC estimation model between CBR and artificial
neural networks (ANN) were provided. ANN and CBR separately
each method has its shortcomings. By combining ANN and CBR
improved results accuracy was obtained. Firstly, using ANN selected
some design features that affect LCC. Then using LCC estimation
results of ANN could raise the accuracy of LCC estimation in CBR
method. Thirdly, using ANN estimate LCC errors and correct errors in
CBR-s estimation results if the accuracy is not enough accurate.
Finally, economically family cars and sport utility vehicle (SUV) was
given as LCC estimation cases using this hybrid approach combining
ANN and CBR.
Abstract: A new OTA-based logarithmic-control variable gain
current amplifier (LCCA) is presented. It consists of two Operational
Transconductance Amplifier (OTA) and two PMOS transistors
biased in weak inversion region. The circuit operates from 0.6V DC
power supply and consumes 0.6 μW. The linear-dB controllable
output range is 43 dB with maximum error less than 0.5dB. The
functionality of the proposed design was confirmed using HSPICE in
0.35μm CMOS process technology.
Abstract: This paper focuses on Land Use and Land Cover Changes (LULCC) occurred in the urban coastal regions of the Mediterranean basin in the last thirty years. LULCC were assessed diachronically (1975-2006) in two urban areas, Rome (Italy) and Athens (Greece), by using CORINE land cover maps. In strictly coastal territories a persistent growth of built-up areas at the expenses of both agricultural and forest land uses was found. On the contrary, a different pattern was observed in the surrounding inland areas, where a high conversion rate of the agricultural land uses to both urban and forest land uses was recorded. The impact of city growth on the complex pattern of coastal LULCC is finally discussed.
Abstract: A Negotiation Support is required on a value-based decision to enable each stakeholder to evaluate and rank the solution alternatives before engaging into negotiation with the other stakeholders. This study demonstrates a process of negotiation support model for selection of a building system from value-based design perspective. The perspective is based on comparison of function and cost of a building system. Multi criteria decision techniques were applied to determine the relative value of the alternative solutions for performing the function. A satisfying option game theory are applied to the criteria of value-based decision which are LCC (life cycle cost) and function based FAST. The results demonstrate a negotiation process to select priorities of a building system. The support model can be extended to an automated negotiation by combining value based decision method, group decision and negotiation support.
Abstract: This paper presents a reliability-based approach to select appropriate wind turbine types for a wind farm considering site-specific wind speed patterns. An actual wind farm in the northern region of Iran with the wind speed registration of one year is studied in this paper. An analytic approach based on total probability theorem is utilized in this paper to model the probabilistic behavior of both turbines- availability and wind speed. Well-known probabilistic reliability indices such as loss of load expectation (LOLE), expected energy not supplied (EENS) and incremental peak load carrying capability (IPLCC) for wind power integration in the Roy Billinton Test System (RBTS) are examined. The most appropriate turbine type achieving the highest reliability level is chosen for the studied wind farm.