Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: In the present paper, a numerical investigation has
been carried out to classify and clarify the effects of paramount
parameters on turbulent impinging slot jets. The effects of nozzle-s
exit turbulent intensity, distance between nozzle and impinging plate
are studied at Reynolds number 5000 and 20000. In addition, the
effect of Mach number that is varied between 0.3-0.8 at a constant
Reynolds number 133000 is investigated to elucidate the effect of
compressibility in impinging jet upon a flat plate. The wall that is
located at the same level with nozzle-s exit confines the flow. A
compressible finite volume solver is implemented for simulation the
flow behavior. One equation Spalart-Allmaras turbulent model is
used to simulate turbulent flow at this study. Assessment of the
Spalart-Allmaras turbulent model at high nozzle to plate distance,
and giving enough insights to characterize the effect of Mach number
at high Reynolds number for the complex impinging jet flow are the
remarkable results of this study.
Abstract: This paper presents a CFD analysis of the flow field
around a thin flat plate of infinite span inclined at 90° to a fluid
stream of infinite extent. Numerical predictions have been compared
to experimental measurements, in order to assess the potential of the
finite volume code of determining the aerodynamic forces acting on a
bluff body invested by a fluid stream of infinite extent.
Several turbulence models and spatial node distributions have
been tested. Flow field characteristics in the neighborhood of the flat
plate have been investigated, allowing the development of a
preliminary procedure to be used as guidance in selecting the
appropriate grid configuration and the corresponding turbulence
model for the prediction of the flow field over a two-dimensional
vertical flat plate.
Abstract: An analysis is made of the flow of an incompressible viscoelastic fluid (of small memory) over a porous plate subject to suction or blowing. It is found that velocity at a point increases with increase in the elasticity in the fluid. It is also shown that wall shear stress depends only on suction and is also independent of the material of fluids. No steady solution for velocity distribution exists when there is blowing at the plate. Temperature distribution in the boundary layer is determined and it is found that temperature at a point decreases with increase in the elasticity in the fluid.
Abstract: Transition prediction of boundary layers has always
been an important problem in fluid mechanics both theoretically and
practically, yet notwithstanding the great effort made by many
investigators, there is no satisfactory answer to this problem. The most
popular method available is so-called e-N method which is heavily
dependent on experiments and experience. The author has proposed
improvements to the e-N method, so to reduce its dependence on
experiments and experience to a certain extent. One of the key
assumptions is that transition would occur whenever the velocity
amplitude of disturbance reaches 1-2% of the free stream velocity.
However, the reliability of this assumption needs to be verified. In this
paper, transition prediction on a flat plate is investigated by using both
the improved e-N method and the parabolized stability equations (PSE)
methods. The results show that the transition locations predicted by
both methods agree reasonably well with each other, under the above
assumption. For the supersonic case, the critical velocity amplitude in
the improved e-N method should be taken as 0.013, whereas in the
subsonic case, it should be 0.018, both are within the range 1-2%.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: A study of various turbulent inflow generation methods
was performed to compare their relative effectiveness for LES
computations of turbulent boundary layers. This study confirmed
the quality of the turbulent information produced by the family of
recycling and rescaling methods which take information from within
the computational domain. Furthermore, more general inflow methods
also proved applicable to such simulations, with a precursor-like
inflow and a random inflow augmented with forcing planes showing
promising results.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.