Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: An Artificial Neural Network based modeling
technique has been used to study the influence of different
combinations of meteorological parameters on evaporation from a
reservoir. The data set used is taken from an earlier reported study.
Several input combination were tried so as to find out the importance
of different input parameters in predicting the evaporation. The
prediction accuracy of Artificial Neural Network has also been
compared with the accuracy of linear regression for predicting
evaporation. The comparison demonstrated superior performance of
Artificial Neural Network over linear regression approach. The
findings of the study also revealed the requirement of all input
parameters considered together, instead of individual parameters
taken one at a time as reported in earlier studies, in predicting the
evaporation. The highest correlation coefficient (0.960) along with
lowest root mean square error (0.865) was obtained with the input
combination of air temperature, wind speed, sunshine hours and
mean relative humidity. A graph between the actual and predicted
values of evaporation suggests that most of the values lie within a
scatter of ±15% with all input parameters. The findings of this study
suggest the usefulness of ANN technique in predicting the
evaporation losses from reservoirs.
Abstract: Fisheries management all around the world is
hampered by the lack, or poor quality, of critical data on fish
resources and fishing operations. The main reasons for the chronic
inability to collect good quality data during fishing operations is the
culture of secrecy common among fishers and the lack of modern
data gathering technology onboard most fishing vessels. In response,
OLRAC-SPS, a South African company, developed fisheries datalogging
software (eLog in short) and named it Olrac. The Olrac eLog
solution is capable of collecting, analysing, plotting, mapping,
reporting, tracing and transmitting all data related to fishing
operations. Olrac can be used by skippers, fleet/company managers,
offshore mariculture farmers, scientists, observers, compliance
inspectors and fisheries management authorities. The authors believe
that using eLog onboard fishing vessels has the potential to
revolutionise the entire process of data collection and reporting
during fishing operations and, if properly deployed and utilised,
could transform the entire commercial fleet to a provider of good
quality data and forever change the way fish resources are managed.
In addition it will make it possible to trace catches back to the actual
individual fishing operation, to improve fishing efficiency and to
dramatically improve control of fishing operations and enforcement
of fishing regulations.
Abstract: LABVIEW is a graphical programming language that has its roots in automation control and data acquisition. In this paper we have utilized this platform to provide a powerful toolset for process identification and control of nonlinear systems based on artificial neural networks (ANN). This tool has been applied to the monitoring and control of a lab-scale distillation column DELTALAB DC-SP. The proposed control scheme offers high speed of response for changes in set points and null stationary error for dual composition control and shows robustness in presence of externally imposed disturbance.
Abstract: A new digital watermarking technique for images that
are sensitive to blocking artifacts is presented. Experimental results
show that the proposed MDCT based approach produces highly
imperceptible watermarked images and is robust to attacks such as
compression, noise, filtering and geometric transformations. The
proposed MDCT watermarking technique is applied to fingerprints
for ensuring security. The face image and demographic text data of
an individual are used as multiple watermarks. An AFIS system was
used to quantitatively evaluate the matching performance of the
MDCT-based watermarked fingerprint. The high fingerprint
matching scores show that the MDCT approach is resilient to
blocking artifacts. The quality of the extracted face and extracted text
images was computed using two human visual system metrics and
the results show that the image quality was high.
Abstract: The creation of a sustainable future depends on the knowledge and involvement of the people, as well as an understanding of the consequences of individual actions. Construction industry has long been associated with the detrimental effects to our mother earth. In Malaysia, the government, professional bodies and private companies are beginning to take heed in the necessity to reduce this environmental problem without restraining the need for development. This paper focuses on the actions undertaken by the Malaysian government, non-government organizations and construction players in promoting sustainability in construction. To ensure that those concerted efforts are not only skin deep in its impact, a survey was conducted to investigate the awareness of the developers regarding this issue and whether those developers has absorb the concept of sustainable construction in their current practices. The survey revealed that although the developers are aware of the rising issues on sustainability, little efforts are generated from them in implementing it. More effort is necessary to boost this application and further stimulate actions and strategies towards a sustainable built environment.
Abstract: Cellular networks provide voice and data services to the users with mobility. To deliver services to the mobile users, the cellular network is capable of tracking the locations of the users, and allowing user movement during the conversations. These capabilities are achieved by the location management. Location management in mobile communication systems is concerned with those network functions necessary to allow the users to be reached wherever they are in the network coverage area. In a cellular network, a service coverage area is divided into smaller areas of hexagonal shape, referred to as cells. The cellular concept was introduced to reuse the radio frequency. Continued expansion of cellular networks, coupled with an increasingly restricted mobile spectrum, has established the reduction of communication overhead as a highly important issue. Much of this traffic is used in determining the precise location of individual users when relaying calls, with the field of location management aiming to reduce this overhead through prediction of user location. This paper describes and compares various location management schemes in the cellular networks.
Abstract: School physical education, through its objectives and
contents, efficiently valorizes the pupils- abilities, developing them,
especially the coordinative skill component, which is the basis of
movement learning, of the development of the daily motility and also
of the special, refined motility required by the practice of certain
sports. Medium school age offers the nervous and motor substratum
needed for the acquisition of complex motor habits, a substratum that
is essential for the coordinative skill. Individuals differ as to the level
at which this function is performed, the extent to which this function
turns an individual into a person that is adapted and adaptable to
complex and various situations. Spatio-temporal orientation, together
with movement combination and coupling, and with kinesthetic,
balance, motor reaction, movement transformation and rhythm
differentiation form the coordinative skills. From our viewpoint,
these are characteristic features with high levels of manifestation in a
complex psychomotor act - valorizing the quality of one-s talent - as
well as indices pertaining to one-s psychomotor intelligence and
creativity.
Abstract: Dual motor drives fed by single inverter is
purposely designed to reduced size and cost with respect to
single motor drives fed by single inverter. Previous researches
on dual motor drives only focus on the modulation and the
averaging techniques. Only a few of them, study the
performance of the drives based on different speed controller
other than Proportional and Integrator (PI) controller. This
paper presents a detailed comparative study on fuzzy rule-base
in Fuzzy Logic speed Controller (FLC) for Dual Permanent
Magnet Synchronous Motor (PMSM) drives. Two fuzzy speed
controllers which are standard and simplified fuzzy speed
controllers are designed and the results are compared and
evaluated. The standard fuzzy controller consists of 49 rules
while the proposed controller consists of 9 rules determined by
selecting the most dominant rules only. Both designs are
compared for wide range of speed and the robustness of both
controllers over load disturbance changes is tested to
demonstrate the effectiveness of the simplified/reduced rulebase.
Abstract: This study investigated the ecological effects of
particulate pollution from a cement factory on the vegetation in the
western Mediterranean coastal desert of Egypt. Variations in
vegetation, soil chemical characters, and some responses of Atriplex
halimus, as a dominant species in the study area, were investigated in
some sites located in different directions from the cement factory
between Burg El-Arab in the east and El-Hammam in the west. The
results showed an obvious decrease in vegetation diversity, in
response to cement-kiln dust pollution, that accompanied by a high
dominance attributed to the high contribution of Atriplex halimus.
Annual species were found to be more sensitive to cement dust
pollution as they all failed to persist in highly disturbed sites. It is
remarkable that cover and phytomass of Atriplex halimus were
increased greatly in response to cement dust pollution, and this was
accompanied by a reduction in the mature seeds and leaf-area of the
plant. The few seeds of the affected individuals seemed to be more
fertile and attained higher germination percentages and exhibited
hardening against drought stress.
Abstract: Tolerance is a tool for achieving a social cohesion, particularly, among individuals and groups with different values. The aim is to study the characteristics of the ethnic tolerance, the inhabitants of Latvia. The ethnic tolerance is taught as a set of conscious and unconscious orientations of the individual in social interaction and inter-ethnic communication. It uses the tools of empirical studies of the ethnic tolerance which allows to identify the explicitly and implicitly levels of the emotional component of Latvia's residents. Explicit measurements were made using the techniques of self-report which revealed the index of the ethnic tolerance and the ethnic identity of the participants. The implicit component was studied using methods based on the effect of the emotional priming. During the processing of the results, there were calculated indicators of the positive and negative implicit attitudes towards members of their own and other ethnicity as well as the explicit parameters of the ethnic tolerance and the ethnic identity of Latvia-s residents. The implicit measurements of the ratio of neighboring ethnic groups against each other showed a mutual negative attitude whereas the explicit measurements indicate a neutral attitude. The data obtained contribute to a further study of the ethnic tolerance of Latvia's residents.
Abstract: The functional response of an infective is the relationship
between an infected individual-s infection rate and the abundance
of the number of susceptibles that one can potentially be infected.
In this paper, we consider defensive attitudes for HIV prevention
(primary prevention) while at the same time emphasizing on offensive
attitudes that reduce infection for those infected (secondary prevention).
We look at how defenses can protect an uninfected individual
in the case where high risk groups such as commercial sex workers
and those who deliberately go out to look for partners. We propose
an infection cycle that begins with a search, then an encounter,
a proposal and contact. The infection cycle illustrates the various
steps an infected individual goes through to successfully infect a
susceptible. For heterogeneous transmission of HIV, there will be no
infection unless there is contact. The ability to avoid an encounter,
detection, proposal and contact constitute defense.
Abstract: The recognition of handwritten numeral is an
important area of research for its applications in post office, banks
and other organizations. This paper presents automatic recognition of
handwritten Kannada numerals based on structural features. Five
different types of features, namely, profile based 10-segment string,
water reservoir; vertical and horizontal strokes, end points and
average boundary length from the minimal bounding box are used in
the recognition of numeral. The effect of each feature and their
combination in the numeral classification is analyzed using nearest
neighbor classifiers. It is common to combine multiple categories of
features into a single feature vector for the classification. Instead,
separate classifiers can be used to classify based on each visual
feature individually and the final classification can be obtained based
on the combination of separate base classification results. One
popular approach is to combine the classifier results into a feature
vector and leaving the decision to next level classifier. This method
is extended to extract a better information, possibility distribution,
from the base classifiers in resolving the conflicts among the
classification results. Here, we use fuzzy k Nearest Neighbor (fuzzy
k-NN) as base classifier for individual feature sets, the results of
which together forms the feature vector for the final k Nearest
Neighbor (k-NN) classifier. Testing is done, using different features,
individually and in combination, on a database containing 1600
samples of different numerals and the results are compared with the
results of different existing methods.
Abstract: Automated material handling is given prime
importance in the semi automated and automated facilities since it
provides solution to the gigantic problems related to inventory and
also support the latest philosophies like just in time production JIT
and lean production. Automated storage and retrieval system is an
antidote (if designed properly) to the facility sufferings like getting
the right material , materials getting perished, long cycle times or
many other similar kind of problems. A working model of automated
storage and retrieval system (AS/RS) is designed and developed
under the design parameters specified by Material Handling Industry
of America (MHIA). Later on analysis was carried out to calculate
the throughput and size of the machine. The possible implementation
of this technology in local scenario is also discussed in this paper.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: The link between urban planning and design principles and the built environment of an urban renewal area is of interest to the field of urban studies. During the past decade, there has also been increasing interest in urban planning and design; this interest is motivated by the possibility that design policies associated with the built environment can be used to control, manage, and shape individual activity and behavior. However, direct assessments and design techniques of the links between how urban planning design policies influence individuals are still rare in the field. Recent research efforts in urban design have focused on the idea that land use and design policies can be used to increase the quality of design projects for an urban renewal area-s built environment. The development of appropriate design techniques for the built environment is an essential element of this research. Quality function deployment (QFD) is a powerful tool for improving alternative urban design and quality for urban renewal areas, and for procuring a citizen-driven quality system. In this research, we propose an integrated framework based on QFD and an Analytic Network Process (ANP) approach to determine the Alternative Technical Requirements (ATRs) to be considered in designing an urban renewal planning and design alternative. We also identify the research designs and methodologies that can be used to evaluate the performance of urban built environment projects. An application in an urban renewal built environment planning and design project evaluation is presented to illustrate the proposed framework.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: Pepper spray use has gained momentum since 1992
and although the active ingredient is readily available, it is considered
a weapon with restricted use in many regions, including The
Bahamas. In light of controversy in the literature regarding the
severity of presenting respiration complaints among individuals postacute
exposure of pepper spray inhalation, this descriptive case series
study was conducted to assess the respiratory status of persons
evaluated during a mass casualty in The Bahamas. Parameters noted
were patients- demographics and respiration severity determined via
clinical examination findings, disposition and follow-up review of the
20 persons. Their most common complaint was difficulty breathing
post exposure. Two required admission and stayed for
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.