Abstract: The performance of Advection Upstream Splitting
Method AUSM schemes are evaluated against experimental flow
fields at different Mach numbers and results are compared with
experimental data of subsonic, supersonic and hypersonic flow fields.
The turbulent model used here is SST model by Menter. The
numerical predictions include lift coefficient, drag coefficient and
pitching moment coefficient at different mach numbers and angle of
attacks. This work describes a computational study undertaken to
compute the Aerodynamic characteristics of different air vehicles
configurations using a structured Navier-Stokes computational
technique. The CFD code bases on the idea of upwind scheme for the
convective (convective-moving) fluxes. CFD results for GLC305
airfoil and cone cylinder tail fined missile calculated on above
mentioned turbulence model are compared with the available data.
Wide ranges of Mach number from subsonic to hypersonic speeds are
simulated and results are compared. When the computation is done
by using viscous turbulence model the above mentioned coefficients
have a very good agreement with the experimental values. AUSM
scheme is very efficient in the regions of very high pressure gradients
like shock waves and discontinuities. The AUSM versions simulate
the all types of flows from lower subsonic to hypersonic flow without
oscillations.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: Flow around a flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube and it is varied in range of 100 to 300. Equations are solved by using finite volume method and results are presented in form of drag and lift coefficient. Results show that drag coefficient of flat tube is up to 66% lower than circular tube with equivalent diameter. In addition, by increasing l/D from 1 to 2, the drag coefficient of flat tube is decreased about 14-27%.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: The pressure drag from a cam shaped tube in cross flows have been investigated experimentally using pressure distribution measurement. The range of angle of attack and Reynolds number based on an equivalent circular tube are within 0≤α≤360° and 2×104< Reeq < 3.4 ×104, respectively. It is found that the pressure drag coefficient is at its highest at α=90° and 270° over the whole range of Reynolds number. Results show that the pressure drag coefficient of the cam shaped tube is lower than that of circular tube with the same surface area for more of the angles of attack. Furthermore, effects of the diameter ratio and finite length of the cam shaped tube upon the pressure drag coefficient are discussed.
Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.
Abstract: In this paper flow around two cam shaped cylinders had been studied numerically. The equivalent diameter of cylinders is 27.6 mm. The space between center to center of two cam shaped cylinders is define as longitudinal pitch ratio and it varies in range of
2 varies in range of 50
Abstract: Heat source addition to the axisymmetric supersonic
inlet may improve the performance parameters, which will increase
the inlet efficiency. In this investigation the heat has been added to
the flow field at some distance ahead of an axisymmetric inlet by
adding an imaginary thermal source upstream of cowl lip. The effect
of heat addition on the drag coefficient, mass flow rate and the
overall efficiency of the inlet have been investigated. The results
show that heat addition causes flow separation, hence to prevent this
phenomena, roughness has been added on the spike surface.
However, heat addition reduces the drag coefficient and the inlet
mass flow rate considerably. Furthermore, the effects of position,
size, and shape on the inlet performance were studied. It is found that
the thermal source deflects the flow streamlines. By improper
location of the thermal source, the optimum condition has been
obtained. For the optimum condition, the drag coefficient is
considerably reduced and the inlet mass flow rate and its efficiency
have been increased slightly. The optimum shape of the heat source
is obtained too.
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.