Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper presents a tested research concept that
implements a complex evolutionary algorithm, genetic algorithm
(GA), in a multi-microcontroller environment. Parallel Distributed
Genetic Algorithm (PDGA) is employed in adaptive beam forming
technique to reduce power usage of adaptive antenna at WCDMA
base station. Adaptive antenna has dynamic beam that requires more
advanced beam forming algorithm such as genetic algorithm which
requires heavy computation and memory space. Microcontrollers are
low resource platforms that are normally not associated with GAs,
which are typically resource intensive. The aim of this project was to
design a cooperative multiprocessor system by expanding the role of
small scale PIC microcontrollers to optimize WCDMA base station
transmitter power. Implementation results have shown that PDGA
multi-microcontroller system returned optimal transmitted power
compared to conventional GA.
Abstract: The objective was to determine the single gene and
interaction effect of composite genotype of beta-kappa casein and
DGAT1 gene on milk yield (MY) and milk composition, content of
milk fat (%FAT), milk protein (%PRO), solid not fat (%SNF), and
total solid (%TS) in crossbred Holstein cows. Two hundred and
thirty- one cows were genotyped with PCR-RFLP for DGAT1 and
composite genotype data of beta-kappa casein from previous work
were used. Two model, (1), and (2), was used to estimate single gene
effect, and interaction effect on the traits, respectively. The
significance of interaction effects on all traits were detected. Most
traits have consistent pattern of significant when model (1), and (2)
were compared, except the effect of composite genotype of betakappa
casein on %FAT, and the effect of DGAT1 on MY, which the
significant difference was detected in only model (1).The results
suggested that when the optimum of all traits was necessary,
interaction effect should be concerned.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: Fracture process in mechanically loaded steel fiber
reinforced high-strength (SFRHSC) concrete is characterized by
fibers bridging the crack providing resistance to its opening.
Structural SFRHSC fracture model was created; material fracture
process was modeled, based on single fiber pull-out laws, which were
determined experimentally (for straight fibers, fibers with end hooks
(Dramix), and corrugated fibers (Tabix)) as well as obtained
numerically ( using FEM simulations). For this purpose experimental
program was realized and pull-out force versus pull-out fiber length
was obtained (for fibers embedded into concrete at different depth
and under different angle). Model predictions were validated by
15x15x60cm prisms 4 point bending tests. Fracture surfaces analysis
was realized for broken prisms with the goal to improve elaborated
model assumptions. Optimal SFRHSC structures were recognized.