Abstract: Over 90% of the world trade is carried by the
international shipping industry. As most of the countries are
developing, seaborne trade continues to expand to bring benefits for
consumers across the world. Studies show that world trade will
increase 70-80% through shipping in the next 15-20 years. Present
global fleet of 70000 commercial ships consumes approximately 200
million tonnes of diesel fuel a year and it is expected that it will be
around 350 million tonnes a year by 2020. It will increase the
demand for fuel and also increase the concentration of CO2 in the
atmosphere. So, it-s essential to control this massive fuel
consumption and CO2 emission. The idea is to utilize a diesel-wind
hybrid system for ship propulsion. Use of wind energy by installing
modern wing-sails in ships can drastically reduce the consumption of
diesel fuel. A huge amount of wind energy is available in oceans.
Whenever wind is available the wing-sails would be deployed and
the diesel engine would be throttled down and still the same forward
speed would be maintained. Wind direction in a particular shipping
route is not same throughout; it changes depending upon the global
wind pattern which depends on the latitude. So, the wing-sail
orientation should be such that it optimizes the use of wind energy.
We have made a computer programme in which by feeding the data
regarding wind velocity, wind direction, ship-motion direction; we
can find out the best wing-sail position and fuel saving for
commercial ships. We have calculated net fuel saving in certain
international shipping routes, for instance, from Mumbai in India to
Durban in South Africa. Our estimates show that about 8.3% diesel
fuel can be saved by utilizing the wind. We are also developing an
experimental model of the ship employing airfoils (small scale wingsail)
and going to test it in National Wind Tunnel Facility in IIT
Kanpur in order to develop a control mechanism for a system of
airfoils.
Abstract: Managing knowledge of research is one way to ensure
just in time information and knowledge to support research strategist
and activities. Unfortunately researcher found the vital research
knowledge in IHL (Institutions of Higher Learning) are scattered,
unstructured and unorganized. Aiming on lay aside conceptual
foundations for understanding and developing OMS (Organizational
Memory System) to facilitate research in IHL, this research revealed
ten factors contributed to the needs of research in the IHL and seven
internal challenges of IHL in promoting research to their academic
members. This study then suggested a comprehensive support of
managing research knowledge using Organizational Memory System
(OMS). Eight OMS characteristics to support research were
identified. Finally the initial work in designing OMS was projected
using knowledge taxonomy. All analysis is derived from pertinent
research paper related to research in IHL and OMS. Further study can
be conducted to validate and verify results presented.
Abstract: Mathematical models can be used to describe the
transmission of disease. Dengue disease is the most significant
mosquito-borne viral disease of human. It now a leading cause of
childhood deaths and hospitalizations in many countries. Variations
in environmental conditions, especially seasonal climatic parameters,
effect to the transmission of dengue viruses the dengue viruses and
their principal mosquito vector, Aedes aegypti. A transmission model
for dengue disease is discussed in this paper. We assume that the
human and vector populations are constant. We showed that the local
stability is completely determined by the threshold parameter, 0 B . If
0 B is less than one, the disease free equilibrium state is stable. If
0 B is more than one, a unique endemic equilibrium state exists and
is stable. The numerical results are shown for the different values of
the transmission probability from vector to human populations.
Abstract: Dengue is a mosquito-borne infection that has peaked to an alarming rate in recent decades. It can be found in tropical and sub-tropical climate. In Malaysia, dengue has been declared as one of the national health threat to the public. This study aimed to map the spatial distributions of dengue cases in the district of Hulu Langat, Selangor via a combination of Geographic Information System (GIS) and spatial statistic tools. Data related to dengue was gathered from the various government health agencies. The location of dengue cases was geocoded using a handheld GPS Juno SB Trimble. A total of 197 dengue cases occurring in 2003 were used in this study. Those data then was aggregated into sub-district level and then converted into GIS format. The study also used population or demographic data as well as the boundary of Hulu Langat. To assess the spatial distribution of dengue cases three spatial statistics method (Moran-s I, average nearest neighborhood (ANN) and kernel density estimation) were applied together with spatial analysis in the GIS environment. Those three indices were used to analyze the spatial distribution and average distance of dengue incidence and to locate the hot spot of dengue cases. The results indicated that the dengue cases was clustered (p < 0.01) when analyze using Moran-s I with z scores 5.03. The results from ANN analysis showed that the average nearest neighbor ratio is less than 1 which is 0.518755 (p < 0.0001). From this result, we can expect the dengue cases pattern in Hulu Langat district is exhibiting a cluster pattern. The z-score for dengue incidence within the district is -13.0525 (p < 0.0001). It was also found that the significant spatial autocorrelation of dengue incidences occurs at an average distance of 380.81 meters (p < 0.0001). Several locations especially residential area also had been identified as the hot spots of dengue cases in the district.
Abstract: Aligned and random nanofibrous scaffolds of PVA/PCL/nHA were fabricated by electrospinning method. The composite nanofibrous scaffolds were subjected to detailed analysis. Morphological investigations revealed that the prepared nanofibers have uniform morphology and the average fiber diameters of aligned and random scaffolds were 135.5 and 290 nm, respectively. The obtained scaffolds have a porous structure with porosity of 88 and 76% for random and aligned nanofibers, respectively. Furthermore, FTIR analysis demonstrated that there were strong intramolecular interactions between the molecules of PVA/PCL/nHA. On the other hand, mechanical characterizations show that aligning the nanofibers, could significantly improve the rigidity of the resultant biocomposite nanofibrous scaffolds.
Abstract: Asiatic Houbara ( Chlamydotis macqueenii ) is a
flagship and vulnerable species. In-situ conservation of this
threatened species demands for knowledge of its habitat selection.
The aim of this study was to determine habitat variables influencing
birds wintering and breeding selection in semi- arid central Iran.
Habitat features of the detected nest and pellet sites were compared
with paired and random plots by quantifying a number of habitat
variables. In wintering habitat use at micro scale houbara selected
sites where vegetation cover was significantly lower compard to
control sites( p< 0.001). Areas with low number of larger plant
species (p=0.03) that were not too close to a vegetation
patch(p
Abstract: The Integrated Performance Modelling Environment
(IPME) is a powerful simulation engine for task simulation and
performance analysis. However, it has no high level cognition such
as memory and reasoning for complex simulation. This article
introduces a knowledge representation and reasoning scheme that can
accommodate uncertainty in simulations of military personnel with
IPME. This approach demonstrates how advanced reasoning models
that support similarity-based associative process, rule-based abstract
process, multiple reasoning methods and real-time interaction can be
integrated with conventional task network modelling to provide
greater functionality and flexibility when modelling operator
performance.
Abstract: Repetitive systems stand for a kind of systems that
perform a simple task on a fixed pattern repetitively, which are
widely spread in industrial fields. Hence, many researchers have been
interested in those systems, especially in the field of iterative learning
control (ILC). In this paper, we propose a finite-horizon tracking
control scheme for linear time-varying repetitive systems with uncertain
initial conditions. The scheme is derived both analytically
and numerically for state-feedback systems and only numerically for
output-feedback systems. Then, it is extended to stable systems with
input constraints. All numerical schemes are developed in the forms
of linear matrix inequalities (LMIs). A distinguished feature of the
proposed scheme from the existing iterative learning control is that
the scheme guarantees the tracking performance exactly even under
uncertain initial conditions. The simulation results demonstrate the
good performance of the proposed scheme.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: the work contains the results of complex investigation
related to the evaluation of condition of working blades of gas turbine
engines during fatigue tests by applying the acoustic emission
method. It demonstrates the possibility of estimating the fatigue
damage of blades in the process of factory tests. The acoustic
emission criteria for detecting and testing the kinetics of fatigue crack
distribution were detected. It also shows the high effectiveness of the
method for non-destructive testing of condition of solid and cooled
working blades for high-temperature gas turbine engines.
Abstract: The world demand for potable water is
increasing every day with growing population. Desalination
using solar energy is suitable for potable water production
from brackish and seawater. In this paper, we present a
theoretical study of solar distillation in a single basin under
the open environmental conditions of Chabahar-Iran. The still
has a base area of 2000mm×500mm with a glass cover
inclined at 25° in order to obtain extra solar energy. We model
the still and conduct its energy balance equations under minor
assumptions. We computed the temperatures of glass cover,
seawater interface, moist air and bottom using numerical
method. The investigation addressed the following: The still
productivity, distilled water salinity and still performance in
terms of the still efficiency. Calculated still productivity in
July was higher than December. So in this paper, we show
that still productivity is directly functioning of solar radiation.
Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.
Abstract: Intellectual capital reporting becomes critical at
universities, mainly due to the fact that knowledge is the main output
as well as input in these institutions. In addition, universities have
continuous external demands for greater information and
transparency about the use of public funds, and are increasingly
provided with greater autonomy regarding their organization,
management, and budget allocation. This situation requires new
management and reporting systems. The purpose of the present study
is to provide a model for intellectual capital report in Spanish
universities. To this end, a questionnaire was sent to every member of
the Social Councils of Spanish public universities in order to identify
which intangible elements university stakeholders demand most. Our
proposal for an intellectual capital report aims to act as a guide to
help the Spanish universities on the road to the presentation of
information on intellectual capital which can assist stakeholders to
make the right decisions.
Abstract: This paper proposed a novel model for short term load
forecast (STLF) in the electricity market. The prior electricity
demand data are treated as time series. The model is composed of
several neural networks whose data are processed using a wavelet
technique. The model is created in the form of a simulation program
written with MATLAB. The load data are treated as time series data.
They are decomposed into several wavelet coefficient series using
the wavelet transform technique known as Non-decimated Wavelet
Transform (NWT). The reason for using this technique is the belief
in the possibility of extracting hidden patterns from the time series
data. The wavelet coefficient series are used to train the neural
networks (NNs) and used as the inputs to the NNs for electricity load
prediction. The Scale Conjugate Gradient (SCG) algorithm is used as
the learning algorithm for the NNs. To get the final forecast data, the
outputs from the NNs are recombined using the same wavelet
technique. The model was evaluated with the electricity load data of
Electronic Engineering Department in Mandalay Technological
University in Myanmar. The simulation results showed that the
model was capable of producing a reasonable forecasting accuracy in
STLF.
Abstract: Some meta-schedulers query the information system of individual supercomputers in order to submit jobs to the least busy supercomputer on a computational Grid. However, this information can become outdated by the time a job starts due to changes in scheduling priorities. The MSR scheme is based on Multiple Simultaneous Requests and can take advantage of opportunities resulting from these priorities changes. This paper presents the SWARM meta-scheduler, which can speed up the execution of large sets of tasks by minimizing the job queuing time through the submission of multiple requests. Performance tests have shown that this new meta-scheduler is faster than an implementation of the MSR scheme and the gLite meta-scheduler. SWARM has been used through the GridQTL project beta-testing portal during the past year. Statistics are provided for this usage and demonstrate its capacity to achieve reliably a substantial reduction of the execution time in production conditions.
Abstract: Performance of millimeter-wave (mm-wave) multiband
orthogonal frequency division multiplexing (MB-OFDM) ultrawideband
(UWB) signal generation using frequency quadrupling
technique and transmission over fiber is experimentally investigated.
The frequency quadrupling is achived by using only one Mach-
Zehnder modulator (MZM) that is biased at maximum transmission
(MATB) point. At the output, a frequency quadrupling signal is
obtained then sent to a second MZM. This MZM is used for MBOFDM
UWB signal modulation. In this work, we demonstrate 30-
GHz mm-wave wireless that carries three-bands OFDM UWB
signals, and error vector magnitude (EVM) is used to analyze the
transmission quality. It is found that our proposed technique leads to
an improvement of 3.5 dB in EVM at 40% of local oscillator (LO)
modulation with comparison to the technique using two cascaded
MZMs biased at minimum transmission (MITB) point.
Abstract: Extensive use of the Internet coupled with the
marvelous growth in e-commerce and m-commerce has created a
huge demand for information security. The Secure Socket Layer
(SSL) protocol is the most widely used security protocol in the
Internet which meets this demand. It provides protection against
eaves droppings, tampering and forgery. The cryptographic
algorithms RC4 and HMAC have been in use for achieving security
services like confidentiality and authentication in the SSL. But recent
attacks against RC4 and HMAC have raised questions in the
confidence on these algorithms. Hence two novel cryptographic
algorithms MAJE4 and MACJER-320 have been proposed as
substitutes for them. The focus of this work is to demonstrate the
performance of these new algorithms and suggest them as dependable
alternatives to satisfy the need of security services in SSL. The
performance evaluation has been done by using practical
implementation method.
Abstract: The importance of ensuring safe meat handling and
processing practices has been demonstrated in global reports on food
safety scares and related illness and deaths. This necessitated stricter
meat safety control strategies. Today, many countries have regulated
towards preventative and systematic control over safe meat
processing at abattoirs utilizing the Hazard Analysis Critical Control
Point (HACCP) principles. HACCP systems have been reported as
effective in managing food safety risks, if correctly implemented.
South Africa has regulated the Hygiene Management System (HMS)
based on HACCP principles applicable to abattoirs. Regulators utilise
the Hygiene Assessment System (HAS) to audit compliance at
abattoirs. These systems were benchmarked from the United
Kingdom (UK). Little research has been done them since inception as
of 2004. This paper presents a review of the two systems, its
implementation and comparison with HACCP. Recommendations are
made for future research to demonstrate the utility of the HMS and
HAS in assuring safe meat to consumers.
Abstract: Plasmodium vivax malaria differs from P. falciparum malaria in that a person suffering from P. vivax infection can suffer relapses of the disease. This is due the parasite being able to remain dormant in the liver of the patients where it is able to re-infect the patient after a passage of time. During this stage, the patient is classified as being in the dormant class. The model to describe the transmission of P. vivax malaria consists of a human population divided into four classes, the susceptible, the infected, the dormant and the recovered. The effect of a time delay on the transmission of this disease is studied. The time delay is the period in which the P. vivax parasite develops inside the mosquito (vector) before the vector becomes infectious (i.e., pass on the infection). We analyze our model by using standard dynamic modeling method. Two stable equilibrium states, a disease free state E0 and an endemic state E1, are found to be possible. It is found that the E0 state is stable when a newly defined basic reproduction number G is less than one. If G is greater than one the endemic state E1 is stable. The conditions for the endemic equilibrium state E1 to be a stable spiral node are established. For realistic values of the parameters in the model, it is found that solutions in phase space are trajectories spiraling into the endemic state. It is shown that the limit cycle and chaotic behaviors can only be achieved with unrealistic parameter values.
Abstract: Short term electricity demand forecasts are required
by power utilities for efficient operation of the power grid. In a
competitive market environment, suppliers and large consumers also
require short term forecasts in order to estimate their energy
requirements in advance. Electricity demand is influenced (among
other things) by the day of the week, the time of year and special
periods and/or days such as Ramadhan, all of which must be
identified prior to modelling. This identification, known as day-type
identification, must be included in the modelling stage either by
segmenting the data and modelling each day-type separately or by
including the day-type as an input. Day-type identification is the
main focus of this paper. A Kohonen map is employed to identify the
separate day-types in Algerian data.