Abstract: An experiment was performed with a 24.5 MeV 14N
beam on a 12C target in the cyclotron DC-60 located in Astana,
Kazakhstan, to study the elastic scattering of 14N on 12C; the
scattering was also analyzed at different energies for tracking the
phenomenon of remarkable structure at large angles. Its aims were to
extend the measurements to very large angles, and attempt to
uniquely identify the elastic scattering potential. Good agreement
between the theoretical and experimental data has been obtained with
suitable optical potential parameters. Optical model calculations with
l -dependent imaginary potentials were also applied to the data and
relatively good agreement was found.
Abstract: This paper presents a formalisation of the different existing code mutation techniques (polymorphism and metamorphism) by means of formal grammars. While very few theoretical results are known about the detection complexity of viral mutation techniques, we exhaustively address this critical issue by considering the Chomsky classification of formal grammars. This enables us to determine which family of code mutation techniques are likely to be detected or on the contrary are bound to remain undetected. As an illustration we then present, on a formal basis, a proof-of-concept metamorphic mutation engine denoted PB MOT, whose detection has been proven to be undecidable.
Abstract: This method decrease usage power (expenditure) in networks on chips (NOC). This method data coding for data transferring in order to reduces expenditure. This method uses data compression reduces the size. Expenditure calculation in NOC occurs inside of NOC based on grown models and transitive activities in entry ports. The goal of simulating is to weigh expenditure for encoding, decoding and compressing in Baseline networks and reduction of switches in this type of networks. KeywordsNetworks on chip, Compression, Encoding, Baseline networks, Banyan networks.
Abstract: This paper studies a vital issue in wireless
communications, which is the transmission of images over Wireless
Personal Area Networks (WPANs) through the Bluetooth network. It
presents a simple method to improve the efficiency of error control
code of old Bluetooth versions over mobile WPANs through
Interleaved Error Control Code (IECC) technique. The encoded
packets are interleaved by simple block interleaver. Also, the paper
presents a chaotic interleaving scheme as a tool against bursts of
errors which depends on the chaotic Baker map. Also, the paper
proposes using the chaotic interleaver instead of traditional block
interleaver with Forward Error Control (FEC) scheme. A comparison
study between the proposed and standard techniques for image
transmission over a correlated fading channel is presented.
Simulation results reveal the superiority of the proposed chaotic
interleaving scheme to other schemes. Also, the superiority of FEC
with proposed chaotic interleaver to the conventional interleavers
with enhancing the security level with chaotic interleaving packetby-
packet basis.
Abstract: In the control theory one attempts to find a controller
that provides the best possible performance with respect to some
given measures of performance. There are many sorts of controllers
e.g. a typical PID controller, LQR controller, Fuzzy controller etc. In
the paper will be introduced polynomial controller with novel tuning
method which is based on the special pole placement encoding
scheme and optimization by Genetic Algorithms (GA). The examples
will show the performance of the novel designed polynomial
controller with comparison to common PID controller.
Abstract: Transmission network expansion planning (TNEP) is a basic part of power system planning that determines where, when and how many new transmission lines should be added to the network. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, lines adequacy rate has not been considered at the end of planning horizon, i.e., expanded network misses adequacy after some times and needs to be expanded again. In this paper, expansion planning has been implemented by merging lines loading parameter in the STNEP and inserting investment cost into the fitness function constraints using genetic algorithm. Expanded network will possess a maximum adequacy to provide load demand and also the transmission lines overloaded later. Finally, adequacy index could be defined and used to compare some designs that have different investment costs and adequacy rates. In this paper, the proposed idea has been tested on the Garvers network. The results show that the network will possess maximum efficiency economically.
Abstract: This paper describes the crashworthiness assessment and improvement of tlting train made of sandwich composites. The crashworhiness assessment of tilting train was conducted according to four collision scenarios of the Korean railway safety law. Collision analysis was carried out using explicit finite element analysis code LS-DYNA 3D. The finite element model consists of 3-D finite element model and 1-D equivalent model to save the finite element modeling and calculation time. It found that the crashworthiness analysis results were satisfied with the performance requirements except the crash scenario-2. In order to meet the crashworthiness requirements for crash scenario-2, the stiffness reinforcement for the laminate composite cover and metal frames of cabmask structure were proposed. Consequentially, it has satisfied the requirement for crash scenario-2.
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: In this paper we proposed the use of Huffman
coding to reduce the PAR of an OFDM system as a distortionless
scrambling technique, and we utilize the amount saved in the
total bit rate by the Huffman coding to send the encoding table
for accurate decoding at the receiver without reducing the
effective throughput. We found that the use of Huffman coding
reduces the PAR by about 6 dB. Also we have investigated the
effect of PAR reduction due to Huffman coding through testing
the spectral spreading and the inband distortion due to HPA with
different IBO values. We found a complete match of our
expectation from the proposed solution with the obtained
simulation results.
Abstract: This paper makes a contribution to the on-going
debate on conceptualization and lexicalization of cutting and
breaking (C&B) verbs by discussing data from Telugu, a language of
India belonging to the Dravidian family. Five Telugu native speakers-
verbalizations of agentive actions depicted in 43 short video-clips
were analyzed. It was noted that verbalization of C&B events in
Telugu requires formal units such as simple lexical verbs, explicator
compound verbs, and other complex verb forms. The properties of
the objects involved, the kind of instruments used, and the manner of
action had differential influence on the lexicalization patterns.
Further, it was noted that all the complex verb forms encode 'result'
and 'cause' sub-events in that order. Due to the polysemy associated
with some of the verb forms, our data does not support the
straightforward bipartition of this semantic domain.
Abstract: The present paper is oriented to classification and application of agent technique in simulation of anticipatory systems, namely those that use simulation models for the aid of anticipation. The main ideas root in the fact that the best way for description of computer simulation models is the technique of describing the simulated system itself (and the translation into the computer code is provided as automatic), and that the anticipation itself is often nested.
Abstract: The effects of upflow liquid velocity (ULV) on
performance of expanded granular sludge bed (EGSB) system were
investigated. The EGSB reactor, made from galvanized steel pipe
0.10 m diameter and 5 m height, had been used to treat piggery
wastewater, after passing through acidification tank. It consisted of
39.3 l working volume in reaction zone and 122 l working volume in
sedimentation zone, at the upper part. The reactor was seeded with
anaerobically digested sludge and operated at the ULVs of 4, 8, 12
and 16 m/h, consecutively, corresponding to organic loading rates of
9.6 – 13.0 kg COD/ (m3.d). The average COD concentrations in the
influent were 9,601 – 13,050 mg/l. The COD removal was not
significantly different, i.e. 93.0% - 94.0%, except at ULV 12 m/h where
SS in the influent was exceptionally high so that VSS washout had
occurred, leading to low COD removal. The FCOD and VFA
concentrations in the effluent of all experiments were not much
different, indicating the same range of treatment performance. The
biogas production decreased at higher ULV and ULV of 4 m/h is
suggested as design criterion for EGSB system.
Abstract: This paper presents a systematic approach for
designing Static Synchronous Series Compensator (SSSC) based
supplementary damping controllers for damping low frequency
oscillations in a single-machine infinite-bus power system. The
design problem of the proposed controller is formulated as an
optimization problem and RCGA is employed to search for optimal
controller parameters. By minimizing the time-domain based
objective function, in which the deviation in the oscillatory rotor
speed of the generator is involved; stability performance of the
system is improved. Simulation results are presented and compared
with a conventional method of tuning the damping controller
parameters to show the effectiveness and robustness of the proposed
design approach.
Abstract: Categorical data based on description of the
agricultural landscape imposed some mathematical and analytical
limitations. This problem however can be overcome by data
transformation through coding scheme and the use of non-parametric
multivariate approach. The present study describes data
transformation from qualitative to numerical descriptors. In a
collection of 103 random soil samples over a 60 hectare field,
categorical data were obtained from the following variables: levels of
nitrogen, phosphorus, potassium, pH, hue, chroma, value and data on
topography, vegetation type, and the presence of rocks. Categorical
data were coded, and Spearman-s rho correlation was then calculated
using PAST software ver. 1.78 in which Principal Component
Analysis was based. Results revealed successful data transformation,
generating 1030 quantitative descriptors. Visualization based on the
new set of descriptors showed clear differences among sites, and
amount of variation was successfully measured. Possible applications
of data transformation are discussed.
Abstract: Many metrics were proposed to evaluate the
characteristics of the analysis and design model of a given product
which in turn help to assess the quality of the product. Function point
metric is a measure of the 'functionality' delivery by the software.
This paper presents an analysis of a set of programs of a project
developed in Cµ through Function Points metric. Function points
are measured for a Data Flow Diagram (DFD) of the case developed
at initial stage. Lines of Codes (LOCs) and possible errors are
calculated with the help of measured Function Points (FPs). The
calculations are performed using suitable established functions.
Calculated LOCs and errors are compared with actual LOCs and
errors found at the time of analysis & design review, implementation
and testing. It has been observed that actual found errors are more
than calculated errors. On the basis of analysis and observations,
authors conclude that function point provides useful insight and helps
to analyze the drawbacks in the development process.
Abstract: Space-time block codes (STBC) and spatial multiplexing
(SM) are promising techniques that effectively exploit multipleinput
multiple-output (MIMO) transmission to achieve more reliable
communication and a higher multiplexing rate, respectively. In this
paper, we study a practical design for hybrid scheme with multi-input
multi-output orthogonal frequency division multiplexing (MIMOOFDM)
systems to flexibly maximize the tradeoff between diversity
and multiplexing gains. Unlike the existing STBC and SM designs
which are suitable for the integer multiplexing rate, the proposed
design can achieve arbitrary number of multiplexing rate.
Abstract: Computer worm detection is commonly performed by
antivirus software tools that rely on prior explicit knowledge of the
worm-s code (detection based on code signatures). We present an
approach for detection of the presence of computer worms based on
Artificial Neural Networks (ANN) using the computer's behavioral
measures. Identification of significant features, which describe the
activity of a worm within a host, is commonly acquired from security
experts. We suggest acquiring these features by applying feature
selection methods. We compare three different feature selection
techniques for the dimensionality reduction and identification of the
most prominent features to capture efficiently the computer behavior
in the context of worm activity. Additionally, we explore three
different temporal representation techniques for the most prominent
features. In order to evaluate the different techniques, several
computers were infected with five different worms and 323 different
features of the infected computers were measured. We evaluated
each technique by preprocessing the dataset according to each one
and training the ANN model with the preprocessed data. We then
evaluated the ability of the model to detect the presence of a new
computer worm, in particular, during heavy user activity on the
infected computers.
Abstract: Two-dimensional finite element model was created in this work to investigate the stresses distribution within rock-like samples with offset open non-persistent joints under biaxial loading. The results of this study have explained the fracture mechanisms observed in tests on rock-like material with open non-persistent offset joints [1]. Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-nodded isoperimetric plain strain element with two degree of freedom per node, and the three-nodded constant strain triangular element with two degree of freedom per node were used in the present study.The results of the present study explained the formation of wing cracks at the tip of the joints for low confining stress as well as the formation of wing cracks at the middle of the joint for the higher confining stress. High shear stresses found in the numerical study at the tip of the joints explained the formation of secondary cracks at the tip of the joints in the experimental study. The study results coincide with the experimental observations which showed that for bridge inclination of 0o, the coalescence occurred due to shear failure and for bridge inclination of 90o the coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occurred due to mixed tensile and shear failure.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: Transmission network expansion planning (TNEP) is an important component of power system planning that its task is to minimize the network construction and operational cost while satisfying the demand increasing, imposed technical and economic conditions. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, the lines adequacy rate has not been studied after the planning horizon, i.e. when the expanded network misses its adequacy and needs to be expanded again. In this paper, in order to take transmission lines condition after expansion in to account from the line loading view point, the adequacy of transmission network is considered for solution of STNEP problem. To obtain optimal network arrangement, a decimal codification genetic algorithm (DCGA) is being used for minimizing the network construction and operational cost. The effectiveness of the proposed idea is tested on the Garver's six-bus network. The results evaluation reveals that the annual worth of network adequacy has a considerable effect on the network arrangement. In addition, the obtained network, based on the DCGA, has lower investment cost and higher adequacy rate. Thus, the network satisfies the requirements of delivering electric power more safely and reliably to load centers.