Abstract: In this paper an optimal convex controller is designed to control the angle of attack of a FOXTROT aircraft. Then the order of the system model is reduced to a low-dimensional state space by using Balanced Truncation Model Reduction Technique and finally the robust stability of the reduced model of the system is tested graphically by using Kharitonov rectangle and Zero Exclusion Principle for a particular range of perturbation value. The same robust stability is tested theoretically by using Frequency Sweeping Function for robust stability.
Abstract: Flow field around hypersonic vehicles is very
complex and difficult to simulate. The boundary layers are squeezed
between shock layer and body surface. Resolution of boundary layer,
shock wave and turbulent regions where the flow field has high
values is difficult of capture. Detached eddy simulation (DES) is a
modification of a RANS model in which the model switches to a
subgrid scale formulation in regions fine enough for LES
calculations. Regions near solid body boundaries and where the
turbulent length scale is less than the maximum grid dimension are
assigned the RANS mode of solution. As the turbulent length scale
exceeds the grid dimension, the regions are solved using the LES
mode. Therefore the grid resolution is not as demanding as pure LES,
thereby considerably cutting down the cost of the computation. In
this research study hypersonic flow is simulated at Mach 8 and
different angle of attacks to resolve the proper boundary layers and
discontinuities. The flow is also simulated in the long wake regions.
Mesh is little different than RANS simulations and it is made dense
near the boundary layers and in the wake regions to resolve it
properly. Hypersonic blunt cone cylinder body with frustrum at angle
5o and 10 o are simulated and there aerodynamics study is performed
to calculate aerodynamics characteristics of different geometries. The
results and then compared with experimental as well as with some
turbulence model (SA Model). The results achieved with DES
simulation have very good resolution as well as have excellent
agreement with experimental and available data. Unsteady
simulations are performed for DES calculations by using duel time
stepping method or implicit time stepping. The simulations are
performed at Mach number 8 and angle of attack from 0o to 10o for
all these cases. The results and resolutions for DES model found
much better than SA turbulence model.
Abstract: In this article, the flow behavior around a NACA 0012 airfoil which is oscillating with different Reynolds numbers and in various amplitudes has been investigated numerically. Numerical simulations have been performed with ANSYS software. First, the 2- D geometry has been studied in different Reynolds numbers and angles of attack with various numerical methods in its static condition. This analysis was to choose the best turbulent model and comparing the grids to have the optimum one for dynamic simulations. Because the analysis was to study the blades of wind turbines, the Reynolds numbers were not arbitrary. They were in the range of 9.71e5 to 22.65e5. The angle of attack was in the range of -41.81° to 41.81°. By choosing the forward wind speed as the independent parameter, the others like Reynolds and the amplitude of the oscillation would be known automatically. The results show that the SST turbulent model is the best choice that leads the least numerical error with respect the experimental ones. Also, a dynamic stall phenomenon is more probable at lower wind speeds in which the lift force is less.
Abstract: Numerical studies on race car aerodynamics at wing
in ground effect have been carried out using a steady 3d, double
precision, pressure-based, and standard k-epsilon turbulence model.
Through various parametric analytical studies we have observed that
at a particular speed and ground clearance of the wings a favorable
negative lift was found high at a particular angle of attack for all the
physical models considered in this paper. The fact is that if the
ground clearance height to chord length (h/c) is too small, the
developing boundary layers from either side (the ground and the
lower surface of the wing) can interact, leading to an altered variation
of the aerodynamic characteristics at wing in ground effect. Therefore
a suitable ground clearance must be predicted throughout the racing
for a better performance of the race car, which obviously depends
upon the coupled effects of the topography, wing orientation with
respect to the ground, the incoming flow features and/or the race car
speed. We have concluded that for the design of high performance
and high speed race cars the adjustable wings capable to alter the
ground clearance and the angles of attack is the best design option for
any race car for racing safely with variable speeds.
Abstract: This paper presents a longitudinal quasi-linear model for the ADMIRE model. The ADMIRE model is a nonlinear model of aircraft flying in the condition of high angle of attack. So it can-t be considered to be a linear system approximately. In this paper, for getting the longitudinal quasi-linear model of the ADMIRE, a state transformation based on differentiable functions of the nonscheduling states and control inputs is performed, with the goal of removing any nonlinear terms not dependent on the scheduling parameter. Since it needn-t linear approximation and can obtain the exact transformations of the nonlinear states, the above-mentioned approach is thought to be appropriate to establish the mathematical model of ADMIRE. To verify this conclusion, simulation experiments are done. And the result shows that this quasi-linear model is accurate enough.
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: Extensive wind tunnel tests have been conducted to
investigate the unsteady flow field over and behind a 2D model of a
660 kW wind turbine blade section in pitching motion. The surface
pressure and wake dynamic pressure variation at a distance of 1.5
chord length from trailing edge were measured by pressure
transducers during several oscillating cycles at 3 reduced frequencies
and oscillating amplitudes. Moreover, form drag and linear
momentum deficit are extracted and compared at various conditions.
The results show that the wake velocity field and surface pressure of
the model have similar behavior before and after the airfoil beyond
the static stall angle of attack. In addition, the effects of reduced
frequency and oscillation amplitudes are discussed.
Abstract: This paper present a new way to find the aerodynamic characteristic equation of missile for the numerical trajectories prediction more accurate. The goal is to obtain the polynomial equation based on two missile characteristic parameters, angle of attack (α ) and flight speed (╬¢ ). First, the understudied missile is modeled and used for flow computational model to compute aerodynamic force and moment. Assume that performance range of understudied missile where range -10< α
Abstract: A parametric study of a mixed-compression
supersonic inlet is performed and reported. The effects of inlet Mach
Numbers, varying from 4 to 10, and angle of attack, varying from 0
to 10, are reported for a constant inlet dynamic pressure. The paper
looked at the variations of mass flow rates through the inlet, gain in
entropy through the inlet, and the angles of the external oblique
shocks. The mass flow rates were found to decrease monotonically
with Mach numbers and increase with angle of attacks. On the other
hand the entropy gain through the inlet increased with increasing
Mach number and angle of attack. The variation in static pressure
was found to be identical from the inlet throat to the exit for Mach
number values higher than 6.
Abstract: Along with increasing development of generation of supersonic planes especially fighters and request for increasing the performance and maneuverability scientists and engineers suggested the delta and double delta wing design. One of the areas which was necessary to be researched, was the Aerodynamic review of this type of wings in high angles of attack at low speeds that was very important in landing and takeoff the planes and maneuvers. Leading Edges of the wings,cause the separation flow from wing surface and then formation of powerful vortex with high rotational speed which studing the mechanism and location of formation and also the position of the vortex breakdown in high angles of attack is very important. In this research, a double delta wing with 76o/45o sweep angles at high angle of attack in steady state and incompressible flow were numerically analyzed with Fluent software. With analaysis of the numerical results, we arrived the most important characteristic of the double delta wings which is keeping of lift at high angles of attacks.
Abstract: The interaction between wakes of bluff body and
airfoil have profound influences on system performance in many
industrial applications, e.g., turbo-machinery and cooling fan. The
present work investigates the effect of configuration include; airfoil-s
angle of attack, transverse and inline spacing of the models, on
frequency behavior of the cylinder-s near-wake. The experiments
carried on under subcritical flow regime, using the hot-wire
anemometry (HWA). The relationship between the Strouhal numbers
and arrangements provide an insight into the global physical
processes of wake interaction and vortex shedding.
Abstract: At very high speeds, bubbles form in the underwater vehicles because of sharp trailing edges or of places where the local pressure is lower than the vapor pressure. These bubbles are called cavities and the size of the cavities grows as the velocity increases. A properly designed cavitator can induce the formation of a single big cavity all over the vehicle. Such a vehicle travelling in the vaporous cavity is called a supercavitating vehicle and the present research work mainly focuses on the dynamic modeling of such vehicles. Cavitation of the fins is also accounted and the effect of the same on trajectory is well explained. The entire dynamics has been developed using the state space approach and emphasis is given on the effect of size and angle of attack of the cavitator. Control law has been established for the motion of the vehicle using Non-linear Dynamic Inverse (NDI) with cavitator as the control surface.
Abstract: The flow field around a flat plate of infinite span has
been investigated for several values of the angle of attack. Numerical
predictions have been compared to experimental measurements, in
order to examine the effect of turbulence model and grid resolution
on the resultant aerodynamic forces acting on the plate. Also the
influence of the free-stream turbulence intensity, at the entrance of
the computational domain, has been investigated. A full campaign of
simulations has been conducted for three inclination angles (9°, 15°
and 30°), in order to obtain some practical guidelines to be used for
the simulation of the flow field around inclined plates and discs.
Abstract: The pressure drag from a cam shaped tube in cross flows have been investigated experimentally using pressure distribution measurement. The range of angle of attack and Reynolds number based on an equivalent circular tube are within 0≤α≤360° and 2×104< Reeq < 3.4 ×104, respectively. It is found that the pressure drag coefficient is at its highest at α=90° and 270° over the whole range of Reynolds number. Results show that the pressure drag coefficient of the cam shaped tube is lower than that of circular tube with the same surface area for more of the angles of attack. Furthermore, effects of the diameter ratio and finite length of the cam shaped tube upon the pressure drag coefficient are discussed.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a three-bladed
small vertical axis Darrieus wind turbine depending on blade chord
curvature with respect to rotor axis.
The adopted survey methodology is based on an analytical code
coupled to a solid modeling software, capable of generating the
desired blade geometry depending on the blade design geometric
parameters, which is linked to a finite volume CFD code for the
calculation of rotor performance.
After describing and validating the model with experimental data,
the results of numerical simulations are proposed on the bases of two
different blade profile architectures, which are respectively
characterized by a straight chord and by a curved one, having a chord
radius equal to rotor external circumference. A CFD campaign of
analysis is completed for three blade-candidate airfoil sections, that is
the recently-developed DU 06-W-200 cambered blade profile, a
classical symmetrical NACA 0021 and its derived cambered airfoil,
characterized by a curved chord, having a chord radius equal to rotor
external circumference.
The effects of blade chord curvature on angle of attack, blade
tangential and normal forces are first investigated and then the
overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of blade camber on overall rotor performance.
Abstract: The unsteady wake of an EPPLER 361 airfoil in
pitching motion has been investigated in a subsonic wind tunnel by
hot-wire anemometry. The airfoil was given the pitching motion
about the one-quarter chord axis at reduced frequency of 0182.
Streamwise mean velocity profiles (wake profiles) were investigated
at several vertically aligned points behind the airfoil at one-quarter
chord downstream distance from trailing edge. Oscillation amplitude
and mean angle of attack were varied to determine the effects on
wake profiles. When the maximum dynamic angle of attack was
below the static stall angle of attack, weak effects on wake were
found by increasing oscillation amplitude and mean angle of attack.
But, for higher angles of attack strong unsteady effects were
appeared on the wake.
Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a small
straight-bladed Darrieus-type vertical axis wind turbine depending on
blade geometrical section. It consists of an analytical code coupled to
a solid modeling software, capable of generating the desired blade
geometry based on the desired blade design geometric parameters.
Such module is then linked to a finite volume commercial CFD code
for the calculation of rotor performance by integration of the
aerodynamic forces along the perimeter of each blade for a full period
of revolution.After describing and validating the computational
model with experimental data, the results of numerical simulations
are proposed on the bases of two candidate airfoil sections, that is a
classical symmetrical NACA 0021 blade profile and the recently
developed DU 06-W-200 non-symmetric and laminar blade
profile.Through a full CFD campaign of analysis, the effects of blade
geometrical section on angle of attack are first investigated and then
the overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of airfoil geometry on overall rotor performance.