Abstract: Nowadays, in most radiotherapy departments, the commercial treatment planning systems (TPS) used to calculate dose distributions needs to be verified; therefore, quick, easy-to-use and low cost dose distribution algorithms are desirable to test and verify the performance of the TPS. In this paper, we put forth an analytical method to calculate the phantom scatter contribution and depth dose on the central axis based on the equivalent square concept. Then, this method was generalized to calculate the profiles at any depth and for several field shapes regular or irregular fields under symmetry and asymmetry photon beam conditions. Varian 2100 C/D and Siemens Primus Plus Linacs with 6 and 18 MV photon beam were used for irradiations. Percentage depth doses (PDDs) were measured for a large number of square fields for both energies, and for 45º wedges which were employed to obtain the profiles in any depth. To assess the accuracy of the calculated profiles, several profile measurements were carried out for some treatment fields. The calculated and measured profiles were compared by gamma-index calculation. All γ–index calculations were based on a 3% dose criterion and a 3 mm dose-to-agreement (DTA) acceptance criterion. The γ values were less than 1 at most points. However, the maximum γ observed was about 1.10 in the penumbra region in most fields and in the central area for the asymmetric fields. This analytical approach provides a generally quick and fairly accurate algorithm to calculate dose distribution for some treatment fields in conventional radiotherapy.
Abstract: In this paper, we analyze the rotor eddy currents losses provoqued by the stator slot harmonics developed in the permanent magnets or pole pieces of synchronous machines. An analytical approach is presented to evaluate the effect of slot ripples on rotor field and losses calculation. This analysis is then tested on a model by 2D/3D finite element (FE) calculation. The results show a good agreement on loss calculations when skin effect is negligible and the magnet is considered.
Abstract: the paper presents the optimization results for several
electrical machines dedicated for powered electric wheel-chairs. The
optimization, using the Hook-Jeeves algorithm, was employed based
on a design approach which takes into consideration the road
conditions. Also, through numerical simulations (based on finite
element method), the analytical approach was validated. The
optimization approach gave satisfactory results and the best suited
variant was chosen for the motorization of the wheel-chair.
Abstract: Study on suppression of interference in time domain equalizers is attempted for high data rate impulse radio (IR) ultra wideband communication system. The narrow band systems may cause interference with UWB devices as it is having very low transmission power and the large bandwidth. SRAKE receiver improves system performance by equalizing signals from different paths. This enables the use of SRAKE receiver techniques in IRUWB systems. But Rake receiver alone fails to suppress narrowband interference (NBI). A hybrid SRake-MMSE time domain equalizer is proposed to overcome this by taking into account both the effect of the number of rake fingers and equalizer taps. It also combats intersymbol interference. A semi analytical approach and Monte-Carlo simulation are used to investigate the BER performance of SRAKEMMSE receiver on IEEE 802.15.3a UWB channel models. Study on non-line of sight indoor channel models (both CM3 and CM4) illustrates that bit error rate performance of SRake-MMSE receiver with NBI performs better than that of Rake receiver without NBI. We show that for a MMSE equalizer operating at high SNR-s the number of equalizer taps plays a more significant role in suppressing interference.
Abstract: The paper applies a discourse analytical approach to investigate important concepts influencing the infrastructure planning process in the region of Scania in southern Sweden. Two discourses, one concerning regional development and one concerning sustainability are identified, discussed and contrasted. It is argued that the perceptions of problems and their suggested solutions related to transportation are based on specific ideas, in turn dependent on the importance given to certain concepts, such as regional enlargement, Scania as a transit region, the national environmental quality goals and regional attractiveness. These concepts, their underlying meaning structures and their relevance for the infrastructure planning process are analyzed. The handling of conflicting interests in the planning process, and the possible implications this may have is also discussed. The results indicate that the regional development discourse is dominant and although the solutions to the problems caused by transport are framed in similar ways in the two discourses a harmonization between conflicting goals is proving difficult to achieve.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: wind catchers have been served as a cooling system, used to provide acceptable ventilation by means of renewable energy of wind. In the present study, the city of Yazd in arid climate is selected as case study. From the architecture point of view, learning about wind catchers in this study is done by means of field surveys. Research method for selection of the case is based on random form, and analytical method. Wind catcher typology and knowledge of relationship governing the wind catcher's architecture were those measures that are taken for the first time. 53 wind catchers were analyzed. The typology of the wind-catchers is done by the physical analyzing, patterns and common concepts as incorporated in them. How the architecture of wind catcher can influence their operations by analyzing thermal behavior are the archetypes of selected wind catchers. Calculating fluids dynamics science, fluent software and numerical analysis are used in this study as the most accurate analytical approach. The results obtained from these analyses show the formal specifications of wind catchers with optimum operation in Yazd. The knowledge obtained from the optimum model could be used for design and construction of wind catchers with more improved operation
Abstract: The development of distributed systems has been affected by the need to accommodate an increasing degree of flexibility, adaptability, and autonomy. The Mobile Agent technology is emerging as an alternative to build a smart generation of highly distributed systems. In this work, we investigate the performance aspect of agent-based technologies for information retrieval. We present a comparative performance evaluation model of Mobile Agents versus Remote Method Invocation by means of an analytical approach. We demonstrate the effectiveness of mobile agents for dynamic code deployment and remote data processing by reducing total latency and at the same time producing minimum network traffic. We argue that exploiting agent-based technologies significantly enhances the performance of distributed systems in the domain of information retrieval.
Abstract: A thin layer on the component surface can be found
with high tensile residual stresses, due to turning operations, which
can dangerously affect the fatigue performance of the component. In
this paper an analytical approach is presented to reconstruct the
residual stress field from a limited incomplete set of measurements.
Airy stress function is used as the primary unknown to directly solve
the equilibrium equations and satisfying the boundary conditions. In
this new method there exists the flexibility to impose the physical
conditions that govern the behavior of residual stress to achieve a
meaningful complete stress field. The analysis is also coupled to a
least squares approximation and a regularization method to provide
stability of the inverse problem. The power of this new method is
then demonstrated by analyzing some experimental measurements
and achieving a good agreement between the model prediction and
the results obtained from residual stress measurement.
Abstract: This paper determines most common model of in-pipe
robots to derive its degree of freedom in order to compare with the
necessary degree of freedom required for a system to move inside
pipelines freely in order to derive analytical reason for losing control
of in-pipe robots at branched pipe. DOF of most common mechanism
in in-pipe robots can be calculated by considering the robot as a
parallel manipulator. A new design based on previously researched
in-pipe robot PAROYS has been suggested, and its possibility to
overcome branched section has been simulated.
Abstract: The main objective developed in this paper is to find a
graphic technique for modeling, simulation and diagnosis of the
industrial systems. This importance is much apparent when it is about
a complex system such as the nuclear reactor with pressurized water
of several form with various several non-linearity and time scales. In
this case the analytical approach is heavy and does not give a fast
idea on the evolution of the system. The tool Bond Graph enabled us
to transform the analytical model into graphic model and the
software of simulation SYMBOLS 2000 specific to the Bond Graphs
made it possible to validate and have the results given by the
technical specifications. We introduce the analysis of the problem
involved in the faults localization and identification in the complex
industrial processes. We propose a method of fault detection applied
to the diagnosis and to determine the gravity of a detected fault. We
show the possibilities of application of the new diagnosis approaches
to the complex system control. The industrial systems became
increasingly complex with the faults diagnosis procedures in the
physical systems prove to become very complex as soon as the
systems considered are not elementary any more. Indeed, in front of
this complexity, we chose to make recourse to Fault Detection and
Isolation method (FDI) by the analysis of the problem of its control
and to conceive a reliable system of diagnosis making it possible to
apprehend the complex dynamic systems spatially distributed applied
to the standard pressurized water nuclear reactor.
Abstract: This paper presents an alternative strategy of queuing
handover called Pseudo Last Useful Instant PLUI scheme for Low
Earth Orbit Mobile Satellite Systems LEO MSSs. The PLUI scheme
uses the same approach as the Last Useful Instant LUI scheme
previously proposed in literature, with less complex implementation.
Simulation tests were carried out using Dynamic Channel Allocation
DCA in order to evaluate the performance of this scheme and also an
analytical approach has been presented to allow the performance
evaluation of Fixed Channel Allocation FCA, with different
handover queuing disciplines. The results show that performances
achieved by the proposed strategy are close to those achieved using
the LUI scheme.
Abstract: Cognitive models allow predicting some aspects of utility
and usability of human machine interfaces (HMI), and simulating
the interaction with these interfaces. The action of predicting is based
on a task analysis, which investigates what a user is required to do
in terms of actions and cognitive processes to achieve a task. Task
analysis facilitates the understanding of the system-s functionalities.
Cognitive models are part of the analytical approaches, that do not
associate the users during the development process of the interface.
This article presents a study about the evaluation of a human
machine interaction with a contextual assistant-s interface using ACTR
and GOMS cognitive models. The present work shows how these
techniques may be applied in the evaluation of HMI, design and
research by emphasizing firstly the task analysis and secondly the
time execution of the task. In order to validate and support our
results, an experimental study of user performance is conducted at
the DOMUS laboratory, during the interaction with the contextual
assistant-s interface. The results of our models show that the GOMS
and ACT-R models give good and excellent predictions respectively
of users performance at the task level, as well as the object level.
Therefore, the simulated results are very close to the results obtained
in the experimental study.
Abstract: This research presented in this paper is an on-going
project of an application of neural network and fuzzy models to
evaluate the sociological factors which affect the educational
performance of the students in Sri Lanka. One of its major goals is to
prepare the grounds to device a counseling tool which helps these
students for a better performance at their examinations, especially at
their G.C.E O/L (General Certificate of Education-Ordinary Level)
examination. Closely related sociological factors are collected as raw
data and the noise of these data are filtered through the fuzzy
interface and the supervised neural network is being utilized to
recognize the performance patterns against the chosen social factors.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: This paper presents the simulation of fragmentation
warhead using a hydrocode, Autodyn. The goal of this research is to
determine the lethal range of such a warhead. This study investigates
the lethal range of warheads with and without steel balls as
preformed fragments. The results from the FE simulation, i.e. initial
velocities and ejected spray angles of fragments, are further processed
using an analytical approach so as to determine a fragment hit density
and probability of kill of a modelled warhead. In order to simulate a
plenty of preformed fragments inside a warhead, the model requires
expensive computation resources. Therefore, this study attempts to
model the problem in an alternative approach by considering an
equivalent mass of preformed fragments to the mass of warhead
casing. This approach yields approximately 7% and 20% difference
of fragment velocities from the analytical results for one and two
layers of preformed fragments, respectively. The lethal ranges of the
simulated warheads are 42.6 m and 56.5 m for warheads with one and
two layers of preformed fragments, respectively, compared to 13.85
m for a warhead without preformed fragment. These lethal ranges are
based on the requirement of fragment hit density. The lethal ranges
which are based on the probability of kill are 27.5 m, 61 m and 70 m
for warheads with no preformed fragment, one and two layers of
preformed fragments, respectively.
Abstract: In this paper, an analytical approach for free vibration
analysis of rectangular and circular membranes is presented. The
method is based on wave approach. From wave standpoint vibration
propagate, reflect and transmit in a structure. Firstly, the propagation
and reflection matrices for rectangular and circular membranes are
derived. Then, these matrices are combined to provide a concise and
systematic approach to free vibration analysis of membranes.
Subsequently, the eigenvalue problem for free vibration of membrane
is formulated and the equation of membrane natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: In this paper, an analytical approach for free vibration
analysis of four edges simply supported rectangular Kirchhoff plates
is presented. The method is based on wave approach. From wave
standpoint vibration propagate, reflect and transmit in a structure.
Firstly, the propagation and reflection matrices for plate with simply
supported boundary condition are derived. Then, these matrices are
combined to provide a concise and systematic approach to free
vibration analysis of a simply supported rectangular Kirchhoff plate.
Subsequently, the eigenvalue problem for free vibration of plates is
formulated and the equation of plate natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: Recently, bianisotropic media again received
increasing importance in electromagnetic theory because of advances
in material science which enable the manufacturing of complex
bianisotropic materials. By using Maxwell's equations and
corresponding boundary conditions, the electromagnetic field
distribution in bianisotropic solenoid coils is determined and the
influence of the bianisotropic behaviour of coil to the impedance and
Q-factor is considered. Bianisotropic media are the largest class of
linear media which is able to describe the macroscopic material
properties of artificial dielectrics, artificial magnetics, artificial chiral
materials, left-handed materials, metamaterials, and other composite
materials. Several special cases of coils, filled with complex
substance, have been analyzed. Results obtained by using the
analytical approach are compared with values calculated by
numerical methods, especially by our new hybrid EEM/BEM method
and FEM.