Abstract: In present study, an approach is adopted where photovoltaic thermal flat plate collector is integrated with compound parabolic concentrator. Analytical expression of temperature dependent electrical efficiency of N number of partially covered Photovoltaic Thermal (PVT) - Compound Parabolic Concentrator (CPC) water collector connected in series has been derived with the help of basic thermal energy balance equations. Analysis has been carried for winter weather condition at Delhi location, India. Energy and exergy performance of N - partially covered Photovoltaic Thermal (PVT) - Compound Parabolic Concentrator (CPC) Water collector system has been compared for two cases: (i) 25% area of water collector covered by PV module, (ii) 75% area of water collector covered by PV module. It is observed that case (i) has been best suited for thermal performance and case (ii) for electrical energy as well as overall exergy.
Abstract: The increasing demand of electric power is giving an
emphasis on the need for the maximum utilization of renewable
energy sources. On the other hand maintaining power quality to
satisfaction of utility is an essential requirement. In this paper the
design aspects of a Unified Power Quality Conditioner integrated
with photovoltaic system in a distributed generation is presented. The
proposed system consist of series inverter, shunt inverter are
connected back to back on the dc side and share a common dc-link
capacitor with Distributed Generation through a boost converter. The
primary task of UPQC is to minimize grid voltage and load current
disturbances along with reactive and harmonic power compensation.
In addition to primary tasks of UPQC, other functionalities such as
compensation of voltage interruption and active power transfer to the
load and grid in both islanding and interconnected mode have been
addressed. The simulation model is design in MATLAB/ Simulation
environment and the results are in good agreement with the published
work.
Abstract: In recent years, the use of renewable energy resources
instead of pollutant fossil fuels and other forms has increased.
Photovoltaic generation is becoming increasingly important as a
renewable resource since it does not cause in fuel costs, pollution,
maintenance, and emitting noise compared with other alternatives
used in power applications. In this paper, Perturb and Observe and
Incremental Conductance methods are used to improve energy
conversion efficiency under different environmental conditions. PI
controllers are used to control easily DC-link voltage, active and
reactive currents. The whole system is simulated under standard
climatic conditions (1000 W/m2, 250C) in MATLAB and the
irradiance is varied from 1000 W/m2 to 300 W/m2. The use of PI
controller makes it easy to directly control the power of the grid
connected PV system. Finally the validity of the system will be
verified through the simulations in MATLAB/Simulink environment.
Abstract: This work studies the effect of thickness on structural
and electrical properties of CuAlS2 thin films grown by two stage
vacuum thermal evaporation technique. CuAlS2 thin films of
thicknesses 50nm, 100nm and 200nm were deposited on suitably
cleaned corning 7059 glass substrate at room temperature (RT). In
the first stage Cu-Al precursors were grown at room temperature by
thermal evaporation and in the second stage Cu-Al precursors were
converted to CuAlS2 thin films by sulfurisation under sulfur
atmosphere at the temperature of 673K. The structural properties of
the films were examined by X-ray diffraction (XRD) technique while
electrical properties of the specimens were studied using four point
probe method. The XRD studies revealed that the films are of
crystalline in nature having tetragonal structure. The variations of the
micro-structural parameters, such as crystallite size (D), dislocation
density ( ), and micro-strain ( ), with film thickness were
investigated. The results showed that the crystallite sizes increase as
the thickness of the film increases. The dislocation density and
micro-strain decreases as the thickness increases. The resistivity ( )
of CuAlS2 film is found to decrease with increase in film thickness,
which is related to the increase of carrier concentration with film
thickness. Thus thicker films exhibit the lowest resistivity and high
carrier concentration, implying these are the most conductive films.
Low electrical resistivity and high carrier concentration are widely
used as the essential components in various optoelectronic devices
such as light-emitting diode and photovoltaic cells.
Abstract: Social networks have recently gained a growing
interest on the web. Traditional formalisms for representing social
networks are static and suffer from the lack of semantics. In this
paper, we will show how semantic web technologies can be used to
model social data. The SemTemp ontology aligns and extends
existing ontologies such as FOAF, SIOC, SKOS and OWL-Time to
provide a temporal and semantically rich description of social data.
We also present a modeling scenario to illustrate how our ontology
can be used to model social networks.
Abstract: Present study focused on the utilization of solar
energy by the help of photovoltaic greenhouse solar dryer under
forced mode. A single slope photovoltaic greenhouse solar dryer has
been proposed and thermal modelling has been developed. Various
parameters have been calculated by thermal modelling such as
greenhouse room temperature, cell temperature, crop temperature and
air temperature at exit of greenhouse. Further cell efficiency, thermal
efficiency, and overall thermal efficiency have been calculated for a
typical day of May and November. It was found that system can
generate equivalent thermal energy up to 7.65 kW and 6.66 kW per
day for clear day of May and November respectively.
Abstract: The power buck converter is the most widely used
DC/DC converter topology. They have a very large application area
such as DC motor drives, photovoltaic power system which require
fast transient responses and high efficiency over a wide range of load
current. This work proposes, the modelling of DC/DC power buck
converter using state-space averaging method and the current-mode
control using a proportional-integral controller. The efficiency of the
proposed model and control loop are evaluated with operating point
changes. The simulation results proved the effectiveness of the linear
model of DC/DC power buck converter.
Abstract: Many embankment dams have suffered failures during
earthquakes due to the increase of pore water pressure under seismic
loading. After analyzing of the behavior of embankment dams under
severe earthquakes, major advances have been attained in the
understanding of the seismic action on dams. The present study concerns numerical analysis of the seismic
response of earth dams. The procedure uses a nonlinear stress-strain
relation incorporated into the code FLAC2D based on the finite
difference method. This analysis provides the variation of the pore
water pressure and horizontal displacement.
Abstract: With 40% of total world energy consumption,
building systems are developing into technically complex large
energy consumers suitable for application of sophisticated power
management approaches to largely increase the energy efficiency
and even make them active energy market participants. Centralized
control system of building heating and cooling managed by
economically-optimal model predictive control shows promising
results with estimated 30% of energy efficiency increase. The research
is focused on implementation of such a method on a case study
performed on two floors of our faculty building with corresponding
sensors wireless data acquisition, remote heating/cooling units and
central climate controller. Building walls are mathematically modeled
with corresponding material types, surface shapes and sizes. Models
are then exploited to predict thermal characteristics and changes in
different building zones. Exterior influences such as environmental
conditions and weather forecast, people behavior and comfort
demands are all taken into account for deriving price-optimal climate
control. Finally, a DC microgrid with photovoltaics, wind turbine,
supercapacitor, batteries and fuel cell stacks is added to make the
building a unit capable of active participation in a price-varying
energy market. Computational burden of applying model predictive
control on such a complex system is relaxed through a hierarchical
decomposition of the microgrid and climate control, where the
former is designed as higher hierarchical level with pre-calculated
price-optimal power flows control, and latter is designed as lower
level control responsible to ensure thermal comfort and exploit
the optimal supply conditions enabled by microgrid energy flows
management. Such an approach is expected to enable the inclusion
of more complex building subsystems into consideration in order to
further increase the energy efficiency.
Abstract: This work aims to investigate the structure–property
relationship in ternary nanocomposites consisting of polypropylene
as the matrix, polyamide 66 as the minor phase and treated nanoclay
DELLITE 67G as the reinforcement. All PP/PA66/Nanoclay systems
with polypropylene grafted maleic anhydride PP-g-MAH as a
compatibilizer were prepared via melt compounding and
characterized in terms of nanoclay content. Morphological structure
was investigated by scanning electron microscopy. The rheological
behavior of the nanocomposites was determined by various methods,
viz melt flow index (MFI) and parallel plate rheological
measurements. The PP/PP-g-MAH/PA66 nanocomposites showed a homogeneous
morphology supporting the compatibility improvement between PP,
PA66, and nanoclay. SEM results revealed the formation of
nanocomposites as the nanoclay was intercalated and exfoliated. In
the ternary nanocomposites, the rheological behavior showed that, the
complex viscosity is increased with increasing the nanoclay. The results showed that the use of nanoclay affects the variations
of storage modulus (G′), loss modulus (G″) and the melt elasticity.
Abstract: This paper focuses on the study of DC-to-DC
converters, which are suitable for low-voltage high-power
applications. The output voltages generated by renewable energy
sources such as photovoltaic arrays and fuel cell stacks are
generally low and required to be increased to high voltage levels.
Development of DC-to-DC converters, which provide high step-up
voltage conversion ratios with high efficiencies and low voltage
stresses, is one of the main issues in the development of renewable
energy systems. A procedure for three converters−conventional
DC-to-DC converter, interleaved boost converter, and isolated flyback
based converter, is illustrated for a given set of specifications. The
selection among the converters for the given application is based on
the voltage conversion ratio, efficiency, and voltage stresses.
Abstract: Green and renewable energy is getting extraordinary
consideration today, because of ecological concerns made by blazing
of fossil powers. Photovoltaic and wind power generation are the
basic decisions for delivering power in this respects. Producing
power by the sun based photovoltaic systems is known to the world,
yet control makers may get confounded to pick between on-grid and
off-grid systems. In this exploration work, an endeavor is made to
compare the off-grid (stand-alone) and on-grid (grid-connected)
frameworks. The work presents relative examination, between two
distinctive PV frameworks situated at V.V.P. Engineering College,
Rajkot. The first framework is 100 kW remain solitary and the
second is 60 kW network joined. The real-time parameters compared
are; output voltage, load current, power in-flow, power output,
performance ratio, yield factor, and capacity factor. The voltage
changes and the power variances in both frameworks are given
exceptional consideration and the examination is made between the
two frameworks to judge the focal points and confinements of both
the frameworks.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Now, the use of renewable energy power generation
has been advanced. In this paper, we compared the usable amount of
resource for photovoltaic power generation which was estimated using
the NEDO formula and the expansion support policy of photovoltaic
power generation which was researched using Internet in the
municipality level in Hokkaido and Aichi Prefecture, Japan. This
paper will contribute to grasp the current situation especially about the
policy. As a result, there were municipalities which seemed to be no
consideration of fitting the amount of resources. We think it would
need to consider the suitability between the resources and policies.
Abstract: The aim of this study is to evaluate the effect of
supplementing broiler starter diet with different levels of an essential
oil blend (EOB) containing capsaicin, carvacrol and cinnamaldehyde
on the performance of broilers. A total of 300 day-old straight-run
Cobb broiler chicks were randomly assigned to three treatments after
7-day group brooding following a completely randomized design
(CRD). Birds assigned in treatment 1 were given starter basal diet
while those in treatments 2 and 3 were given starter basal diet with
400 mg/kg antibiotic growth promoter (AGP) and 150 mg/kg EOB,
respectively, until the 28th day. Basal finisher feed were given for all
the treatments until harvest. Following 37 d feeding, body weight
gain, feed consumption, feed efficiency, dressing percentage,
livability and jejunal villi height were determined. Results showed no
significant differences (P>0.05) in growth performance. However,
villi height and crypt depth was significantly lower for birds fed
EOB.
Abstract: The photovoltaic and the semiconductor industries are
in growth and it is necessary to supply a large amount of silicon to
maintain this growth. Since silicon is still the best material for the
manufacturing of solar cells and semiconductor components so the
pure silicon like solar grade and semiconductor grade materials are
demanded. There are two main routes for silicon production:
metallurgical and chemical. In this article, we reviewed the
electrotecnological installations and systems for semiconductor
manufacturing. The main task is to design the installation which can
produce SOG Silicon from river sand by one work unit.
Abstract: Direct Torque Control (DTC) is an AC drive control
method especially designed to provide fast and robust responses. In
this paper a progressive algorithm for direct torque control of threephase
induction drive system supplied by photovoltaic arrays using
voltage source inverter to control motor torque and flux with
maximum power point tracking at different level of insolation is
presented. Experimental results of the new DTC method obtained by
an experimental rapid prototype system for drives are presented.
Simulation and experimental results confirm that the proposed system
gives quick, robust torque and speed responses at constant switching
frequencies.
Abstract: The use of solar energy as a source for pumping water
is one of the promising areas in the photovoltaic (PV) application.
The energy of photovoltaic pumping systems (PVPS) can be widely
improved by employing an MPPT algorithm. This will lead
consequently to maximize the electrical motor speed of the system.
This paper presents a modified incremental conductance (IncCond)
MPPT algorithm with direct control method applied to a standalone
PV pumping system. The influence of the algorithm parameters on
system behavior is investigated and compared with the traditional
(INC) method. The studied system consists of a PV panel, a DC-DC
boost converter, and a PMDC motor-pump. The simulation of the
system by MATLAB-SIMULINK is carried out. Simulation results
found are satisfactory.
Abstract: Digital cameras to reduce cost, use an image sensor to
capture color images. Color Filter Array (CFA) in digital cameras
permits only one of the three primary (red-green-blue) colors to be
sensed in a pixel and interpolates the two missing components
through a method named demosaicking. Captured data is interpolated
into a full color image and compressed in applications. Color
interpolation before compression leads to data redundancy. This
paper proposes a new Vector Quantization (VQ) technique to
construct a VQ codebook with Differential Evolution (DE)
Algorithm. The new technique is compared to conventional Linde-
Buzo-Gray (LBG) method.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive three phase inverter (TPI) for a photovoltaic
(PV) system at commercial level. The proposed model uses phase
locked loop (PLL) to synchronize the TPI with the power electric
grid (PEG) and performs MPC control in a dq reference frame. TPI
model consists of a boost converter (BC), maximum power point
tracking (MPPT) control, and a three-leg voltage source inverter
(VSI). The operational model of VSI is used to synthesize the
sinusoidal current and track the reference. The model is validated
using a 35.7 kW PV system in Matlab/Simulink. Implementation
results show simplicity and accuracy, as well as reliability of the
model.