Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: In this paper, we consider components of discrete event imitating model, implementing a simulation model by using JAVA and performing an input analysis of the data and an output analysis of the simulation results. Was lead development of imitating model of mass service system with n (n≥1) devices of service. On the basis of the developed process of a multithreading simulated the distributed processes with presence of synchronization. Was developed the algorithm of event-oriented simulation, was received results of system functioning with n devices of service.
Abstract: In seismic survey, the information regarding the
velocity of compression wave (Vp) as well as shear wave (Vs) are
very useful especially during the seismic interpretation. Previous
studies showed that both Vp and Vs determined by above methods
are totally different with respect to each other but offered good
approximation. In this study, both Vp and Vs of consolidated granite
rock were studied by using ultrasonic testing method and seismic
refraction method. In ultrasonic testing, two different condition of
rock are used which is dry and wet. The differences between Vp and
Vs getting by using ultrasonic testing and seismic refraction were
investigated and studied. The effect of water content in granite rock
towards the value of Vp and Vs during ultrasonic testing are also
measured. Within this work, the tolerance of the differences between
the velocity of seismic wave getting from ultrasonic testing and the
velocity of seismic wave getting from seismic refraction are also
measured and investigated.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: As business environments are rapidly changing,
the manufacturing system must be reconfigured to adapt to
various customer needs. In order to cope with this challenge, it
is quintessential to test industrial control logic rapidly and
easily in the design time, and monitor operational behavior in
the run time of automated manufacturing system. Proposed
integrated model for virtual prototyping and operational
monitoring of industrial control logic is to improve limitations
of current ladder programming practices and general discrete
event simulation method. Each plant layout model using HMI
package and object-oriented control logic model is designed
independently and is executed simultaneously in integrated
manner to reflect design practices of automation system in the
design time. Control logic is designed and executed using UML
activity diagram without considering complicated control
behavior to deal with current trend of reconfigurable
manufacturing. After the physical installation, layout model of
virtual prototype constructed in the design time is reused for
operational monitoring of system behavior during run time.
Abstract: The peculiarities of the nanoscale structure-phase
states formed after electroexplosive carburizing and subsequent
electron-beam treatment of technically pure titanium surface in different regimes are established by methods of transmission electron
diffraction microscopy and physical mechanisms are discussed. Electroexplosive carburizing leads to surface layer formation
(40 m thickness) with increased (in 3.5 times) microhardness. It consists of β-titanium, graphite (monocrystals 100-150 nm,
polycrystals 5-10 nm, amorphous particles 3-5nm), TiC (5-10 nm), β-Ti02 (2-20nm). After electron-beam treatment additionally increasing the microhardness the surface layer consists of TiC.
Abstract: The counting and analysis of blood cells allows the
evaluation and diagnosis of a vast number of diseases. In particular,
the analysis of white blood cells (WBCs) is a topic of great interest to
hematologists. Nowadays the morphological analysis of blood cells is
performed manually by skilled operators. This involves numerous
drawbacks, such as slowness of the analysis and a nonstandard
accuracy, dependent on the operator skills. In literature there are only
few examples of automated systems in order to analyze the white
blood cells, most of which only partial. This paper presents a
complete and fully automatic method for white blood cells
identification from microscopic images. The proposed method firstly
individuates white blood cells from which, subsequently, nucleus and
cytoplasm are extracted. The whole work has been developed using
MATLAB environment, in particular the Image Processing Toolbox.
Abstract: Biodiesel as an alternative fuel for diesel engines has been developed for some three decades now. While it is gaining wide acceptance in Europe, USA and some parts of Asia, the same cannot be said of Africa. With more than 35 countries in the continent depending on imported crude oil, it is necessary to look for alternative fuels which can be produced from resources available locally within any country. Hence this study presents performance of single cylinder diesel engine using blends of shea butter biodiesel. Shea butter was transformed into biodiesel by transesterification process. Tests are conducted to compare the biodiesel with baseline diesel fuel in terms of engine performance and exhaust emission characteristics. The results obtained showed that the addition of biodiesel to diesel fuel decreases the brake thermal efficiency (BTE) and increases the brake specific fuel consumption (BSFC). These results are expected due to the lower energy content of biodiesel fuel. On the other hand while the NOx emissions increased with increase in biodiesel content in the fuel blends, the emissions of carbon monoxide (CO), un-burnt hydrocarbon (UHC) and smoke opacity decreased. The engine performance which indicates that the biodiesel has properties and characteristics similar to diesel fuel and the reductions in exhaust emissions make shea butter biodiesel a viable additive or substitute to diesel fuel.
Abstract: A new technique based on Pattern search optimization is proposed for estimating different solar cell parameters in this paper. The estimated parameters are the generated photocurrent, saturation current, series resistance, shunt resistance, and ideality factor. The proposed approach is tested and validated using double diode model to show its potential. Performance of the developed approach is quite interesting which signifies its potential as a promising estimation tool.
Abstract: Today, cancer remains one of the major diseases that
lead to death. The main obstacle in chemotherapy as a main cancer
treatment is the toxicity to normal cells due to Multidrug Resistance
(MDR) after the use of anticancer drugs. Proposed solution to
overcome this problem is the use of MDR efflux inhibitor of cinchona
alkaloids which is delivered together with anticancer drugs
encapsulated in the form of polymeric nanoparticles. The particles
were prepared by the hydration method. The characterization of
nanoparticles was particle size, zeta potential, entrapment efficiency
and in vitro drug release. Combination nanoparticle size ranged 29-45
nm with a neutral surface charge. Entrapment efficiency was above
87% for the use quinine, quinidine or cinchonidine in combination
with etoposide. The release test results exhibited that the cinchona
alkaloids release released faster than that of etoposide. Collectively,
cinchona alkaloids can be packaged along with etoposide in
nanomicelles for better cancer therapy.
Abstract: The purpose of this study was to develop and examine a
Teaching Commitment Scale of Health and Physical Education
(TCS-HPE) for Taiwanese elementary school teachers. First of all,
based on teaching commitment related theory and literatures to
develop a original scale with 40 items, later both stratified random
sampling and cluster sampling were used to sample participants.
During the first stage, 300 teachers were sampled and 251 valid scales
(83.7%) returned. Later, the data was analyzed by exploratory factor
analysis to obtain 74.30% of total variance for the construct validity.
The Cronbach-s alpha coefficient of sum scale reliability was 0.94, and
subscale coefficients were between 0.80 and 0.96. In the second stage,
400 teachers were sampled and 318 valid scales (79.5%) returned.
Finally, this study used confirmatory factor analysis to test validity and
reliability of TCS-HPE. The result showed that the fit indexes reached
acceptable criteria(¤ç2
(246 ) =557.64 , p
Abstract: In this paper, a nonlinear model predictive swing-up
and stabilizing sliding controller is proposed for an inverted
pendulum-cart system. In the swing up phase, the nonlinear model
predictive control is formulated as a nonlinear programming problem
with energy based objective function. By solving this problem at
each sampling instant, a sequence of control inputs that optimize the
nonlinear objective function subject to various constraints over a
finite horizon are obtained. Then, this control drives the pendulum to
a predefined neighborhood of the upper equilibrium point, at where
sliding mode based model predictive control is used to stabilize the
systems with the specified constraints. It is shown by the simulations
that, due to the way of formulating the problem, short horizon
lengths are sufficient for attaining the swing up goal.
Abstract: Repetitive systems stand for a kind of systems that
perform a simple task on a fixed pattern repetitively, which are
widely spread in industrial fields. Hence, many researchers have been
interested in those systems, especially in the field of iterative learning
control (ILC). In this paper, we propose a finite-horizon tracking
control scheme for linear time-varying repetitive systems with uncertain
initial conditions. The scheme is derived both analytically
and numerically for state-feedback systems and only numerically for
output-feedback systems. Then, it is extended to stable systems with
input constraints. All numerical schemes are developed in the forms
of linear matrix inequalities (LMIs). A distinguished feature of the
proposed scheme from the existing iterative learning control is that
the scheme guarantees the tracking performance exactly even under
uncertain initial conditions. The simulation results demonstrate the
good performance of the proposed scheme.
Abstract: In today-s global and competitive market,
manufacturing companies are working hard towards improving their
production system performance. Most companies develop production
systems that can help in cost reduction. Manufacturing systems
consist of different elements including production methods,
machines, processes, control and information systems. Human issues
are an important part of manufacturing systems, yet most companies
do not pay sufficient attention to them. In this paper, a workforce
planning (WP) model is presented. A non-linear programming model
is developed in order to minimize the hiring, firing, training and
overtime costs. The purpose is to determine the number of workers
for each worker type, the number of workers trained, and the number
of overtime hours. Moreover, a decision support system (DSS) based
on the proposed model is introduced using the Excel-Lingo software
interfacing feature. This model will help to improve the interaction
between the workers, managers and the technical systems in
manufacturing.
Abstract: Two short sediment cores collected from mangrove
areas of Manori and Thane creeks along Mumbai coast were analysed
for sediment composition and metals (Fe, Mn, Cu, Pb, Co, Ni, Zn, Cr
and V). The statistical analysis of Pearson correlation matrix proved
that there is a significant relationship between metal concentration
and finer grain size in Manori creek while poor correlation was
observed in Thane creek. Based on the enrichment factor, the present
metal to background metal ratios clearly reflected maximum
enrichment of Cu and Pb in Manori creek and Mn in Thane creek.
Geoaccumulation index calculated indicate that the study area is
unpolluted with respect to Fe, Mn, Co, Ni, Zn and Cr in both the
cores while moderately polluted with Cu and Pb in Manori creek.
Based on contamination degree, both the core sediments were found
to be considerably contaminated with metals.
Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: A novel path planning approach is presented to solve
optimal path in stochastic, time-varying networks under priori traffic
information. Most existing studies make use of dynamic programming
to find optimal path. However, those methods are proved to
be unable to obtain global optimal value, moreover, how to design
efficient algorithms is also another challenge.
This paper employs a decision theoretic framework for defining
optimal path: for a given source S and destination D in urban transit
network, we seek an S - D path of lowest expected travel time
where its link travel times are discrete random variables. To solve
deficiency caused by the methods of dynamic programming, such as
curse of dimensionality and violation of optimal principle, an integer
programming model is built to realize assignment of discrete travel
time variables to arcs. Simultaneously, pruning techniques are also
applied to reduce computation complexity in the algorithm. The final
experiments show the feasibility of the novel approach.