Abstract: Biofuels, like biobutanol, have been recognized for
being renewable and sustainable fuels which can be produced from
lignocellulosic biomass. To convert lignocellulosic biomass to
biofuel, pretreatment process is an important step to remove
hemicelluloses and lignin to improve enzymatic hydrolysis. Dilute
acid pretreatment has been successful developed for pretreatment of
corncobs and the optimum conditions of dilute sulfuric and
phosphoric acid pretreatment were obtained at 120 °C for 5 min with
15:1 liquid to solid ratio and 140 °C for 10 min with 10:1 liquid to
solid ratio, respectively. The result shows that both of acid
pretreatments gave the content of total sugar approximately 34–35
g/l. In case of inhibitor content (furfural), phosphoric acid
pretreatment gives higher than sulfuric acid pretreatment.
Characterizations of corncobs after pretreatment indicate that both of
acid pretreatments can improve enzymatic accessibility and the better
results present in corncobs pretreated with sulfuric acid in term of
surface area, crystallinity, and composition analysis.
Abstract: This paper presents a computational methodology
based on matrix operations for a computer based solution to the
problem of performance analysis of software reliability models
(SRMs). A set of seven comparison criteria have been formulated to
rank various non-homogenous Poisson process software reliability
models proposed during the past 30 years to estimate software
reliability measures such as the number of remaining faults, software
failure rate, and software reliability. Selection of optimal SRM for
use in a particular case has been an area of interest for researchers in
the field of software reliability. Tools and techniques for software
reliability model selection found in the literature cannot be used with
high level of confidence as they use a limited number of model
selection criteria. A real data set of middle size software project from
published papers has been used for demonstration of matrix method.
The result of this study will be a ranking of SRMs based on the
Permanent value of the criteria matrix formed for each model based
on the comparison criteria. The software reliability model with
highest value of the Permanent is ranked at number – 1 and so on.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: Corporate credit rating prediction using statistical and
artificial intelligence (AI) techniques has been one of the attractive
research topics in the literature. In recent years, multiclass
classification models such as artificial neural network (ANN) or
multiclass support vector machine (MSVM) have become a very
appealing machine learning approaches due to their good
performance. However, most of them have only focused on classifying
samples into nominal categories, thus the unique characteristic of the
credit rating - ordinality - has been seldom considered in their
approaches. This study proposes new types of ANN and MSVM
classifiers, which are named OMANN and OMSVM respectively.
OMANN and OMSVM are designed to extend binary ANN or SVM
classifiers by applying ordinal pairwise partitioning (OPP) strategy.
These models can handle ordinal multiple classes efficiently and
effectively. To validate the usefulness of these two models, we applied
them to the real-world bond rating case. We compared the results of
our models to those of conventional approaches. The experimental
results showed that our proposed models improve classification
accuracy in comparison to typical multiclass classification techniques
with the reduced computation resource.
Abstract: The present work compares the performance of three
turbulence modeling approach (based on the two-equation k -ε
model) in predicting erosive wear in multi-size dense slurry flow
through rotating channel. All three turbulence models include
rotation modification to the production term in the turbulent kineticenergy
equation. The two-phase flow field obtained numerically
using Galerkin finite element methodology relates the local flow
velocity and concentration to the wear rate via a suitable wear model.
The wear models for both sliding wear and impact wear mechanisms
account for the particle size dependence. Results of predicted wear
rates using the three turbulence models are compared for a large
number of cases spanning such operating parameters as rotation rate,
solids concentration, flow rate, particle size distribution and so forth.
The root-mean-square error between FE-generated data and the
correlation between maximum wear rate and the operating
parameters is found less than 2.5% for all the three models.
Abstract: Most of the image watermarking methods, using the properties of the human visual system (HVS), have been proposed in literature. The component of the visual threshold is usually related to either the spatial contrast sensitivity function (CSF) or the visual masking. Especially on the contrast masking, most methods have not mention to the effect near to the edge region. Since the HVS is sensitive what happens on the edge area. This paper proposes ultrasound image watermarking using the visual threshold corresponding to the HVS in which the coefficients in a DCT-block have been classified based on the texture, edge, and plain area. This classification method enables not only useful for imperceptibility when the watermark is insert into an image but also achievable a robustness of watermark detection. A comparison of the proposed method with other methods has been carried out which shown that the proposed method robusts to blockwise memoryless manipulations, and also robust against noise addition.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: Polynomial bases and normal bases are both used for
elliptic curve cryptosystems, but field arithmetic operations such as
multiplication, inversion and doubling for each basis are implemented
by different methods. In general, it is said that normal bases, especially
optimal normal bases (ONB) which are special cases on normal bases,
are efficient for the implementation in hardware in comparison with
polynomial bases. However there seems to be more examined by
implementing and analyzing these systems under similar condition. In
this paper, we designed field arithmetic operators for each basis over
GF(2233), which field has a polynomial basis recommended by SEC2
and a type-II ONB both, and analyzed these implementation results.
And, in addition, we predicted the efficiency of two elliptic curve
cryptosystems using these field arithmetic operators.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: In this paper, we present the video quality measure
estimation via a neural network. This latter predicts MOS (mean
opinion score) by providing height parameters extracted from
original and coded videos. The eight parameters that are used are: the
average of DFT differences, the standard deviation of DFT
differences, the average of DCT differences, the standard deviation
of DCT differences, the variance of energy of color, the luminance
Y, the chrominance U and the chrominance V. We chose Euclidean
Distance to make comparison between the calculated and estimated
output.
Abstract: A new code synchronization algorithm is proposed in
this paper for the secondary cell-search stage in wideband CDMA
systems. Rather than using the Cyclically Permutable (CP) code in the
Secondary Synchronization Channel (S-SCH) to simultaneously
determine the frame boundary and scrambling code group, the new
synchronization algorithm implements the same function with less
system complexity and less Mean Acquisition Time (MAT). The
Secondary Synchronization Code (SSC) is redesigned by splitting into
two sub-sequences. We treat the information of scrambling code group
as data bits and use simple time diversity BCH coding for further
reliability. It avoids involved and time-costly Reed-Solomon (RS)
code computations and comparisons. Analysis and simulation results
show that the Synchronization Error Rate (SER) yielded by the new
algorithm in Rayleigh fading channels is close to that of the
conventional algorithm in the standard. This new synchronization
algorithm reduces system complexities, shortens the average
cell-search time and can be implemented in the slot-based cell-search
pipeline. By taking antenna diversity and pipelining correlation
processes, the new algorithm also shows its flexible application in
multiple antenna systems.
Abstract: The study of the variability of the postural strategies
in low back pain patients, as a criterion in evaluation of the
adaptability of this system to the environmental demands is the
purpose of this study. A cross-sectional case-control study was
performed on 21 recurrent non-specific low back pain patients and 21
healthy volunteers. The electromyography activity of Deltoid,
External Oblique (EO), Transverse Abdominis/Internal Oblique
(TrA/IO) and Erector Spine (ES) muscles of each person was
recorded in 75 rapid arm flexion with maximum acceleration.
Standard deviation of trunk muscles onset relative to deltoid muscle
onset were statistically analyzed by MANOVA . The results show
that chronic low back pain patients exhibit less variability in their
anticipatory postural adjustments (APAs) in comparison with the
control group. There is a decrease in variability of postural control
system of recurrent non-specific low back pain patients that can
result in the persistence of pain and chronicity by decreasing the
adaptability to environmental demands.
Abstract: Numerous concrete structures projects are currently running in Libya as part of a US$50 billion government funding. The
quality of concrete used in 20 different construction projects were assessed based mainly on the concrete compressive strength achieved. The projects are scattered all over the country and are at
various levels of completeness. For most of these projects, the
concrete compressive strength was obtained from test results of a
150mm standard cube mold. Statistical analysis of collected concrete
compressive strengths reveals that the data in general followed a
normal distribution pattern. The study covers comparison and assessment of concrete quality aspects such as: quality control, strength range, data standard deviation, data scatter, and ratio of minimum strength to design strength. Site quality control for these projects ranged from very good to poor according to ACI214 criteria [1]. The ranges (Rg) of the strength (max. strength – min. strength) divided by average strength are from (34% to 160%). Data scatter is
measured as the range (Rg) divided by standard deviation () and is
found to be (1.82 to 11.04), indicating that the range is ±3σ.
International construction companies working in Libya follow
different assessment criteria for concrete compressive strength in lieu
of national unified procedure. The study reveals that assessments of
concrete quality conducted by these construction companies usually
meet their adopted (internal) standards, but sometimes fail to meet
internationally known standard requirements. The assessment of
concrete presented in this paper is based on ACI, British standards
and proposed Libyan concrete strength assessment criteria.
Abstract: This paper present a new method for design of power
system stabilizer (PSS) based on sliding mode control (SMC)
technique. The control objective is to enhance stability and improve
the dynamic response of the multi-machine power system. In order to
test effectiveness of the proposed scheme, simulation will be carried
out to analyze the small signal stability characteristics of the system
about the steady state operating condition following the change in
reference mechanical torque and also parameters uncertainties. For
comparison, simulation of a conventional control PSS (lead-lag
compensation type) will be carried out. The main approach is
focusing on the control performance which later proven to have the
degree of shorter reaching time and lower spike.
Abstract: This research evaluated and compared the thermodynamic performance of heat pump systems which can be run under two different modes as air to air and air to water by using only one compressor. To achieve this comparison an experimental performance study was made on a traditional vapor compressed heat pump system that can be run air to air mode and air to water mode by help of a valve. The experiments made under different thermal conditions. Thermodynamic performance of the systems are presented and compared with each other for different working conditions.
Abstract: The impact of fixed speed squirrel cage type as well as
variable speed doubly fed induction generators (DFIG) on dynamic
performance of a multimachine power system has been investigated.
Detailed models of the various components have been presented and
the integration of asynchronous and synchronous generators has been
carried out through a rotor angle based transform. Simulation studies
carried out considering the conventional dynamic model of squirrel
cage asynchronous generators show that integration, as such, could
degrade to the AC system performance transiently. This article
proposes a frequency or power controller which can effectively
control the transients and restore normal operation of fixed speed
induction generator quickly. Comparison of simulation results
between classical cage and doubly-fed induction generators indicate
that the doubly fed induction machine is more adaptable to
multimachine AC system. Frequency controller installed in the DFIG
system can also improve its transient profile.
Abstract: Eye localization is necessary for face recognition and
related application areas. Most of eye localization algorithms reported
so far still need to be improved about precision and computational
time for successful applications. In this paper, we propose an eye
location method based on multi-scale Gabor feature vectors, which is
more robust with respect to initial points. The eye localization based
on Gabor feature vectors first needs to constructs an Eye Model Bunch
for each eye (left or right eye) which consists of n Gabor jets and
average eye coordinates of each eyes obtained from n model face
images, and then tries to localize eyes in an incoming face image by
utilizing the fact that the true eye coordinates is most likely to be very
close to the position where the Gabor jet will have the best Gabor jet
similarity matching with a Gabor jet in the Eye Model Bunch. Similar
ideas have been already proposed in such as EBGM (Elastic Bunch
Graph Matching). However, the method used in EBGM is known to be
not robust with respect to initial values and may need extensive search
range for achieving the required performance, but extensive search
ranges will cause much more computational burden. In this paper, we
propose a multi-scale approach with a little increased computational
burden where one first tries to localize eyes based on Gabor feature
vectors in a coarse face image obtained from down sampling of the
original face image, and then localize eyes based on Gabor feature
vectors in the original resolution face image by using the eye
coordinates localized in the coarse scaled image as initial points.
Several experiments and comparisons with other eye localization
methods reported in the other papers show the efficiency of our
proposed method.
Abstract: It is suggested to evaluate environmental performance
of energy sector using Data Envelopment Analysis with nondiscretionary
factors (DEA-ND) with relative indicators as inputs and
outputs. The latter allows for comparison of the objects essentially
different in size. Inclusion of non-discretionary factors serves
separation of the indicators that are beyond the control of the objects.
A virtual perfect object comprised of maximal outputs and minimal
inputs was added to the group of actual ones. In this setting, explicit
solution of the DEA-ND problem was obtained. Energy sector of the
United States was analyzed using suggested approach for the period
of 1980 – 2006 with expected values of economic indicators for 2030
used for forming the perfect object. It was obtained that
environmental performance has been increasing steadily for the
period from 7.7% through 50.0% but still remains well below the
prospected level
Abstract: This paper presents a new stable robust adaptive controller and observer design for a class of nonlinear systems that contain i. Coupling of unmeasured states and unknown parameters ii. Unknown dead zone at the system actuator. The system is firstly cast into a modified form in which the observer and parameter estimation become feasible. Then a stable robust adaptive controller, state observer, parameter update laws are derived that would provide global adaptive system stability and desirable performance. To validate the approach, simulation was performed to a single-link mechanical system with a dynamic friction model and unknown dead zone exists at the system actuation. Then a comparison is presented with the results when there is no dead zone at the system actuation.
Abstract: Erwinia carotovora var. carotovora is the main cause of soft rot in potatoes. Hyphaene thebaica was studied for biocontrol of E. carotovora which inhibited growth of E. carotovora on solid medium, a comparative study of classical and ultrasound-assisted extractions of Hyphaene thebaica fruit. The use of ultrasound decreased significant the total time of treatment and increase the total amount of crude extract. The crude extract was subjected to determine the in vitro, by a bioassay technique revealed that the treatment of paper disks with ultrasound extraction of Hyphaene thebaica reduced the growth of pathogen and produced inhibition zones up to 38mm in diameter. The antioxidant activity of ultrasound-ethanolic extract of Doum fruits (Hyphaene thebaica) was determined. Data obtained showed that the extract contains the secondary metabolites such as Tannins, Saponin, Flavonoids, Phenols, Steroids, Terpenoids, Glycosides and Alkaloids.