Abstract: The aim of this study was to establish the feasibility of a minute incremental exercise testing protocol in young asthma children. Twenty-two children with clinically diagnosed mild to moderate asthma volunteered to participate. The maximum incremental exercise test was performed using a cycle ergometer with an electromagnetic braking. A warm-up unloaded for 2 minutes then the workload was started at 40 watts for 2 minutes, and then stepwise increments of 8 watts per 2 minutes were applied. The pedaling frequency was set at 50 rpm. Ventilation and gas exchange were measured with a breath-by-breath automatic metabolic measurement system. Results showed that this test was well tolerated by all asthmatic children. Most of the children reached the VO2 plateau and satisfied the criteria for maximal respiratory exchange ratio of ≥ 1. This Study demonstrated that this testing protocol was suitable for young asthmatic children.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: Although the STL (stereo lithography) file format is
widely used as a de facto industry standard in the rapid prototyping
industry due to its simplicity and ability to tessellation of almost all
surfaces, but there are always some defects and shortcoming in their
usage, which many of them are difficult to correct manually. In
processing the complex models, size of the file and its defects grow
extremely, therefore, correcting STL files become difficult. In this
paper through optimizing the exiting algorithms, size of the files and
memory usage of computers to process them will be reduced. In spite
of type and extent of the errors in STL files, the tail-to-head
searching method and analysis of the nearest distance between tails
and heads techniques were used. As a result STL models sliced
rapidly, and fully closed contours produced effectively and errorless.
Abstract: In sport, human resources management gives special
attention to method of applying volunteers, their maintenance, and
participation of volunteers with each other and management
approaches for better operation of events celebrants. The recognition
of volunteers- characteristics and motives is important to notice,
because it makes the basis of their participation and commitment at
sport environment. The motivation and commitment of 281
volunteers were assessed using the organizational commitment scale,
motivation scale and personal characteristics questionnaire.The
descriptive results showed that; 64% of volunteers were women with
age average 21/24 years old. They were physical education student,
single (71/9%), without occupation (53%) and with average of 5
years sport experience. Their most important motivation was career
factor and the most important commitment factor was normative
factor. The results of examining the hypothesized showed that; age,
sport experience and education are effective in the amount of
volunteers- commitment. And the motive factors such as career,
material, purposive and protective factors also have the power to
predict the amount of sports volunteers- commitment value.
Therefore it is recommended to provide possible opportunities for
volunteers and carrying out appropriate instructional courses by
events executive managers.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: An effective approach for unbalanced three-phase
distribution power flow solutions is proposed in this paper. The
special topological characteristics of distribution networks have been
fully utilized to make the direct solution possible. Two matrices–the
bus-injection to branch-current matrix and the branch-current to busvoltage
matrix– and a simple matrix multiplication are used to
obtain power flow solutions. Due to the distinctive solution
techniques of the proposed method, the time-consuming LU
decomposition and forward/backward substitution of the Jacobian
matrix or admittance matrix required in the traditional power flow
methods are no longer necessary. Therefore, the proposed method is
robust and time-efficient. Test results demonstrate the validity of the
proposed method. The proposed method shows great potential to be
used in distribution automation applications.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: The possibility of intrinsic electromagnetic fields
within living cells and their resonant self-interaction and interaction
with ambient electromagnetic fields is suggested on the basis of a
theoretical and experimental study. It is reported that intrinsic
electromagnetic fields are produced in the form of radio-frequency
and infra-red photons within atoms (which may be coupled or
uncoupled) in cellular structures, such as the cell cytoskeleton and
plasma membrane. A model is presented for the interaction of these
photons among themselves or with atoms under a dipole-dipole
coupling, induced by single-photon or two-photon processes. This
resonance is manifested by conspicuous field amplification and it is
argued that it is possible for these resonant photons to undergo
tunnelling in the form of evanescent waves to a short range (of a few
nanometers to micrometres). This effect, suggested as a resonant
photon tunnelling mechanism in this report, may enable these fields
to act as intracellular signal communication devices and as bridges
between macromolecules or cellular structures in the cell
cytoskeleton, organelles or membrane. A brief overview of an
experimental technique and a review of some preliminary results are
presented, in the detection of these fields produced in living cell
membranes under physiological conditions.
Abstract: In this paper, we show that C*-tensor product of an arbitrary C*-algebra A, (not unital necessary) and C*-algebra B without ground state, have no approximately inner strongly continuous one-parameter group of *-automorphisms.
Abstract: A shaft-type activated sludge reactor has been
developed in order to study the feasibility of high-rate wastewater
treatment. The reactor having volume of about 14.5 L was operated
with the acclimated mixed activated sludge under batch and
continuous mode using a synthetic wastewater as feed. The batch
study was performed with varying chemical oxygen demand (COD)
concentrations of 1000–3500 mg·L-1 for a batch period up to 9 h. The
kinetic coefficients: Ks, k, Y and kd were obtained as 2040.2 mg·L-1
and 0.105 h-1, 0.878 and 0.0025 h-1 respectively from Monod-s
approach. The continuous study showed a stable and steady state
operation for a hydraulic retention time (HRT) of 8 h and influent
COD of about 1000 mg·L-1. A maximum COD removal efficiency of
about 80% was attained at a COD loading rate and food-tomicroorganism
(F/M) ratio (COD basis) of 3.42 kg·m-3d-1 and 1.0
kg·kg-1d-1 respectively under a HRT of 8 h. The reactor was also
found to handle COD loading rate and F/M ratio of 10.8 kg·m-3d-1
and 2.20 kg·kg-1d-1 respectively showing a COD removal efficiency
of about 46%.
Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.
Abstract: Conventional concentrically-braced frame (CBF)
systems have limited drift capacity before brace buckling and related
damage leads to deterioration in strength and stiffness. Self-centering
concentrically-braced frame (SC-CBF) systems have been developed
to increase drift capacity prior to initiation of damage and minimize
residual drift. SC-CBFs differ from conventional CBFs in that the
SC-CBF columns are designed to uplift from the foundation at a
specified level of lateral loading, initiating a rigid-body rotation
(rocking) of the frame. Vertically-aligned post-tensioning bars resist
uplift and provide a restoring force to return the SC-CBF columns to
the foundation (self-centering the system). This paper presents a
parametric study of different prototype buildings using SC-CBFs.
The bay widths of the SC-CBFs have been varied in these buildings
to study different geometries. Nonlinear numerical analyses of the
different SC-CBFs are presented to illustrate the effect of frame
geometry on the behavior and dynamic response of the SC-CBF
system.
Abstract: Nowadays there is a growing interest in biofuel production in most countries because of the increasing concerns about hydrocarbon fuel shortage and global climate changes, also for enhancing agricultural economy and producing local needs for transportation fuel. Ethanol can be produced from biomass by the hydrolysis and sugar fermentation processes. In this study ethanol was produced without using expensive commercial enzymes from sugarcane bagasse. Alkali pretreatment was used to prepare biomass before enzymatic hydrolysis. The comparison between NaOH, KOH and Ca(OH)2 shows NaOH is more effective on bagasse. The required enzymes for biomass hydrolysis were produced from sugarcane solid state fermentation via two fungi: Trichoderma longibrachiatum and Aspergillus niger. The results show that the produced enzyme solution via A. niger has functioned better than T. longibrachiatum. Ethanol was produced by simultaneous saccharification and fermentation (SSF) with crude enzyme solution from T. longibrachiatum and Saccharomyces cerevisiae yeast. To evaluate this procedure, SSF of pretreated bagasse was also done using Celluclast 1.5L by Novozymes. The yield of ethanol production by commercial enzyme and produced enzyme solution via T. longibrachiatum was 81% and 50% respectively.
Abstract: In this paper, a method for matching image segments
using triangle-based (geometrical) regions is proposed. Triangular
regions are formed from triples of vertex points obtained from a
keypoint detector (SIFT). However, triangle regions are subject to
noise and distortion around the edges and vertices (especially acute
angles). Therefore, these triangles are expanded into parallelogramshaped
regions. The extracted image segments inherit an important
triangle property; the invariance to affine distortion. Given two
images, matching corresponding regions is conducted by computing
the relative affine matrix, rectifying one of the regions w.r.t. the other
one, then calculating the similarity between the reference and
rectified region. The experimental tests show the efficiency and
robustness of the proposed algorithm against geometrical distortion.
Abstract: Consider the Gregory integration (G) formula
with end corrections where h Δ is the forward difference operator with step size h. In this study we prove that can be optimized by
minimizing some of the coefficient k a in the remainder term by
particle swarm optimization. Experimental tests prove that can be rendered a powerful formula for library use.
Abstract: The objective of this work is to explicit knowledge on the interactions between the chlorophyll-a and nine meroplankton larvae of epibenthonic fauna. The studied case is the Arraial do Cabo upwelling system, Southeastern of Brazil, which provides different environmental conditions. To assess this information a network approach based in probability estimative was used. Comparisons among the generated graphs are made in the light of different water masses, application of Shannon biodiversity index, and the closeness and betweenness centralities measurements. Our results show the main pattern among different water masses and how the core organisms belonging to the network skeleton are correlated to the main environmental variable. We conclude that the approach of complex networks is a promising tool for environmental diagnostic.
Abstract: The usual correctness condition for a schedule of
concurrent database transactions is some form of serializability of
the transactions. For general forms, the problem of deciding whether
a schedule is serializable is NP-complete. In those cases other approaches
to proving correctness, using proof rules that allow the steps
of the proof of serializability to be guided manually, are desirable.
Such an approach is possible in the case of conflict serializability
which is proved algebraically by deriving serial schedules using
commutativity of non-conflicting operations. However, conflict serializability
can be an unnecessarily strong form of serializability restricting
concurrency and thereby reducing performance. In practice,
weaker, more general, forms of serializability for extended models of
transactions are used. Currently, there are no known methods using
proof rules for proving those general forms of serializability. In this
paper, we define serializability for an extended model of partitioned
transactions, which we show to be as expressive as serializability
for general partitioned transactions. An algebraic method for proving
general serializability is obtained by giving an initial-algebra specification
of serializable schedules of concurrent transactions in the
model. This demonstrates that it is possible to conduct algebraic
proofs of correctness of concurrent transactions in general cases.
Abstract: The frontal area in the brain is known to be involved in
behavioral judgement. Because a Kanji character can be discriminated
visually and linguistically from other characters, in Kanji character
discrimination, we hypothesized that frontal event-related potential
(ERP) waveforms reflect two discrimination processes in separate
time periods: one based on visual analysis and the other based
on lexcical access. To examine this hypothesis, we recorded ERPs
while performing a Kanji lexical decision task. In this task, either a
known Kanji character, an unknown Kanji character or a symbol was
presented and the subject had to report if the presented character was
a known Kanji character for the subject or not. The same response
was required for unknown Kanji trials and symbol trials. As a preprocessing
of signals, we examined the performance of a method
using independent component analysis for artifact rejection and found
it was effective. Therefore we used it. In the ERP results, there
were two time periods in which the frontal ERP wavefoms were
significantly different betweeen the unknown Kanji trials and the
symbol trials: around 170ms and around 300ms after stimulus onset.
This result supported our hypothesis. In addition, the result suggests
that Kanji character lexical access may be fully completed by around
260ms after stimulus onset.