Abstract: Routing security is a major concerned in Wireless
Sensor Network since a large scale of unattended nodes is deployed
in ad hoc fashion with no possibility of a global addressing due to a
limitation of node-s memory and the node have to be self organizing
when the systems require a connection with the other nodes. It
becomes more challenging when the nodes have to act as the router
and tightly constrained on energy and computational capabilities
where any existing security mechanisms are not allowed to be fitted
directly. These reasons thus increasing vulnerabilities to the network
layer particularly and to the whole network, generally. In this paper,
a Dynamic Window Secured Implicit Geographic Forwarding
(DWSIGF) routing is presented where a dynamic time is used for
collection window to collect Clear to Send (CTS) control packet in
order to find an appropriate hoping node. The DWIGF is expected to
minimize a chance to select an attacker as the hoping node that
caused by a blackhole attack that happen because of the CTS rushing
attack, which promise a good network performance with high packet
delivery ratios.
Abstract: In this paper a hybrid technique of Genetic Algorithm
and Simulated Annealing (HGASA) is applied for Fractal Image
Compression (FIC). With the help of this hybrid evolutionary
algorithm effort is made to reduce the search complexity of matching
between range block and domain block. The concept of Simulated
Annealing (SA) is incorporated into Genetic Algorithm (GA) in order
to avoid pre-mature convergence of the strings. One of the image
compression techniques in the spatial domain is Fractal Image
Compression but the main drawback of FIC is that it involves more
computational time due to global search. In order to improve the
computational time along with acceptable quality of the decoded
image, HGASA technique has been proposed. Experimental results
show that the proposed HGASA is a better method than GA in terms
of PSNR for Fractal image Compression.
Abstract: In this paper, a numerical study has been made to
analyze the transient 2-D flows of a viscous incompressible fluid
through channels with forward or backward constriction. Problems
addressed include flow through sudden contraction and sudden
expansion channel geometries with rounded and increasingly sharp
reentrant corner. In both the cases, numerical results are presented for
the separation and reattachment points, streamlines, vorticity and
flow patterns. A fourth order accurate compact scheme has been
employed to efficiently capture steady state solutions of the
governing equations. It appears from our study that sharpness of the
throat in the channel is one of the important parameters to control the
strength and size of the separation zone without modifying the
general flow patterns. The comparison between the two cases shows
that the upstream geometry plays a significant role on vortex growth
dynamics.
Abstract: Considering today-s increasing speed of change,
radical and innovative improvement - Kaikaku, is a necessity parallel
to continuous incremental improvement - Kaizen, especially for
SME-s in order to attain the competitive edge needed to be profitable.
During 2011, a qualitative single case study with the objective of
realizing a kaikaku in production has been conducted. The case study
was run as a one year project using a collaborative approach
including both researchers and company representatives. The case
study was conducted with the purpose of gaining further knowledge
about kaikaku realization as well as its implications. The empirical
results provide insights about the great productivity results achieved
by applying a specific kaikaku realization approach. However, it also
sheds light on the difficulty and contradiction of combining
innovation management and production system development.
Abstract: Repairing of the cracks by fiber metal laminates
(FMLs) was first done by some aeronautical laboratories in early
1970s. In this study, experimental investigations were done on the
effect of repairing the center-cracked aluminum plates using the FML
patches. The repairing processes were conducted to characterize the
response of the repaired structures to tensile tests. The composite
patches were made of one aluminum layer and two woven glassepoxy
composite layers. Three different crack lengths in three crack
angles and different patch lay-ups were examined. It was observed
for the lengthen cracks, the effect of increasing the crack angle on
ultimate tensile load in the structure was increase. It was indicated
that the situation of metal layer in the FML patches had an important
effect on the tensile response of the tested specimens. It was found
when the aluminum layer is farther, the ultimate tensile load has the
highest amount.
Abstract: Free and open source software is gaining popularity at
an unprecedented rate of growth. Organizations despite some
concerns about the quality have been using them for various
purposes. One of the biggest concerns about free and open source
software is post release software defects and their fixing. Many
believe that there is no appropriate support available to fix the bugs.
On the contrary some believe that due to the active involvement of
internet user in online forums, they become a major source of
communicating the identification and fixing of defects in open source
software. The research model of this empirical investigation
establishes and studies the relationship between open source software
defects and online public forums. The results of this empirical study
provide evidence about the realities of software defects myths of
open source software. We used a dataset consist of 616 open source
software projects covering a broad range of categories to study the
research model of this investigation. The results of this investigation
show that online forums play a significant role identifying and fixing
the defects in open source software.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: Buckling-Restrained Braced Frame system(BRBFs)
are a new type of steel seismic-load-resisting system that has found
use in several countries because of its efficiency and its promise of
seismic performance far superior to that of conventional braced
frames. The system is addressed in the 2005 edition of the AISC
Seismic Provisions for Structural Steel Buildings, also a set of design
provisions has been developed by NEHRP. This report illustrates the
seismic design of buckling restrained braced frames and compares
the result of design in the application of earthquake load for ordinary
bracing systems and buckling restrained bracing systems to see the
advantage and disadvantages of this new type of seismic resisting
system in comparison with the old Ordinary Concentric Braced
Frame systems (OCBFs); they are defined by the provisions
governing their design.
Abstract: Microarray experiments are information rich; however, extensive data mining is required to identify the patterns that characterize the underlying mechanisms of action. For biologists, a key aim when analyzing microarray data is to group genes based on the temporal patterns of their expression levels. In this paper, we used an iterative clustering method to find temporal patterns of gene expression. We evaluated the performance of this method by applying it to real sporulation data and simulated data. The patterns obtained using the iterative clustering were found to be superior to those obtained using existing clustering algorithms.
Abstract: The selective recovery of heavy metals of Cu, Zn, Ni and Cr from a mixed plating sludge by sulfidation and oxidation treatment was targeted in this study. At first, the mixed plating sludge was simultaneously subjected to an extraction and Cu sulfidation process at pH=1.5 to dissolve heavy metals and to precipitate Cu2+ as CuS. In the next step, the sulfidation treatment of Zn was carried out at pH=4.5 and the residual solution was subjected to an oxidation treatment of chromium with H2O2 at pH=10.0. After the experiments, the selectivity of metal precipitation and the chromium oxidation ratio were evaluated. As results, it was found that the filter cake obtained after selective sulfidation of Cu was composed of 96.6% of Cu (100% equals to the sum of Cu, Zn, Ni and Cr contents). Such findings confirmed that almost complete extraction of heavy metals was achieved at pH=1.5 and also that Cu could be selectively recovered as CuS. Further, the filter cake obtained at pH=4.5 was composed of 91.5% Zn and 6.83% of Cr. Regarding the chromium oxidation step, the chromium oxidation ratio was found to increase with temperature and the addition of oxidation agent of H2O2, but only oxidation ratio of 59% was achieved at a temperature of 60°C and H2O2 to Cr3+ equivalent ratio of 180.
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: Wrist pulse analysis for identification of health status
is found in Ancient Indian as well as Chinese literature. The preprocessing
of wrist pulse is necessary to remove outlier pulses and
fluctuations prior to the analysis of pulse pressure signal. This paper
discusses the identification of irregular pulses present in the pulse
series and intricacies associated with the extraction of time domain
pulse features. An approach of Dynamic Time Warping (DTW) has
been utilized for the identification of outlier pulses in the wrist pulse
series. The ambiguity present in the identification of pulse features is
resolved with the help of first derivative of Ensemble Average of
wrist pulse series. An algorithm for detecting tidal and dicrotic notch
in individual wrist pulse segment is proposed.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: The growing problem of youth unemployment in
Egypt after the 25th January Revolution has directed the attention of
some human resource experts towards considering remote
employment as a partial remedy for the unemployed youth instead of
the unavailable traditional jobs, a trend which will also help with the
congested offices and unsolved traffic problem in Cairo and spread
a flexible work culture, but despite of that, the main issue remains
unresolved for these organizations to deal with the system challenges.
In the past few years, in developed countries, there has been a
growing trend for many companies to shift to remote employment
instead of the traditional office employment for many reasons: due to
the growing technological advances that helped some employees do
their work from home on a part time basis, the need for achieving an
employee-s work balance in the middle of unbalanced complicated
life, top management focus on employee-s productivity rather their
time spent at work. The objective of this paper is to study and analyze
the advantages and challenges that Egypt-s labor force will be facing
in their implementation of remote or virtual employment in both
government and private organizations after the 25th January
revolution. Therefore, the research question will be: What are the
advantages and different challenges that Egyptian organizations
might face in their implementation for remote employment system
and how can they manage these challenges for the system to work
effectively? The study is divided into six main parts: the introduction,
objective and importance of the study, research problem,
methodology, experience of some countries that implemented remote
employment, advantages and challenges of implementing remote
employment in Egypt and then the conclusion which discuses the
results and recommendations of the study.
Abstract: It is very important to determine reference temperature when convective temperature because it should be used to calculate the temperature potential. This paper deals with the development of a new method that can determine heat transfer coefficient and reference free stream temperature simultaneously, based on transient heat transfer experiments with using two narrow band thermo-tropic liquid crystals (TLC's). The method is validated through error analysis in terms of the random uncertainties in the measured temperatures. It is shown how the uncertainties in heat transfer coefficient and free stream temperature can be reduced. The general method described in this paper is applicable to many heat transfer models with unknown free stream temperature.
Abstract: Texture classification is a trendy and a catchy
technology in the field of texture analysis. Textures, the repeated
patterns, have different frequency components along different
orientations. Our work is based on Texture Classification and its
applications. It finds its applications in various fields like Medical
Image Classification, Computer Vision, Remote Sensing,
Agricultural Field, and Textile Industry. Weed control has a major
effect on agriculture. A large amount of herbicide has been used for
controlling weeds in agriculture fields, lawns, golf courses, sport
fields, etc. Random spraying of herbicides does not meet the exact
requirement of the field. Certain areas in field have more weed
patches than estimated. So, we need a visual system that can
discriminate weeds from the field image which will reduce or even
eliminate the amount of herbicide used. This would allow farmers to
not use any herbicides or only apply them where they are needed. A
machine vision precision automated weed control system could
reduce the usage of chemicals in crop fields. In this paper, an
intelligent system for automatic weeding strategy Multi Resolution
Combined Statistical & spatial Frequency is used to discriminate the
weeds from the crops and to classify them as narrow, little and broad
weeds.
Abstract: We introduce a new interactive 3D simulator of ocular motion and expressions suitable for: (1) character animation applications to game design, film production, HCI (Human Computer Interface), conversational animated agents, and virtual reality; (2) medical applications (ophthalmic neurological and muscular pathologies: research and education); and (3) real time simulation of unconscious cognitive and emotional responses (for use, e.g., in psychological research). Using state-of-the-art computer animation technology we have modeled and rigged a physiologically accurate 3D model of the eyes, eyelids, and eyebrow regions and we have 'optimized' it for use with an interactive and web deliverable platform. In addition, we have realized a prototype device for realtime control of eye motions and expressions, including unconsciously produced expressions, for application as in (1), (2), and (3) above. The 3D simulator of eye motion and ocular expression is, to our knowledge, the most advanced/realistic available so far for applications in character animation and medical pedagogy.
Abstract: Achieving success is a highly critical issue for the
companies to survive in a competitive business environment. The
construction industry is also an area where there is strong
competition due to a large number of construction contractors. There
have been many factors such as qualified employees, quality
workmanship and financial management that can lead to company
success in the construction industry. The aim of this study was to
investigate the critical factors leading to construction company
success. Within this context, a survey was carried out among 40
Turkish construction companies which are located in the Northwest
region of Turkey. In this survey, top-level managers and owners of
the companies were interviewed. The interviews took place over a
five month period between January and May 2007. Finally, the
ranking of the critical success factors has been determined by using
the Simple Multi Attribute Rating Technique (SMART). Based on
the results, business management, financial conditions and
owner/manager characteristics were determined as the most
important factors to company success.
Abstract: Computer animation is a widely adopted technique used to specify the movement of various objects on screen. The key issue of this technique is the specification of motion. Motion Control Methods are such methods which are used to specify the actions of objects. This paper discusses the various types of motion control methods with special focus on behavioral animation. A behavioral model is also proposed which takes into account the emotions and perceptions of an actor which in turn generate its behavior. This model makes use of an expert system to generate tasks for the actors which specify the actions to be performed in the virtual environment.