Abstract: In this paper, an estimation accuracy of multiple moving
talker tracking using a microphone array is improved. The tracking
can be achieved by the adaptive method in which two algorithms are integrated, namely, the PAST (Projection Approximation Subspace
Tracking) algorithm and the IPLS (Interior Point Least Square) algorithm. When either talker begins to speak again after a silent
period, an appropriate feasible region for an evaluation function of
the IPLS algorithm might not be set. Then, the tracking fails due to the incorrect updating. Therefore, if an increment of the number of
active talkers is detected, the feasible region must be reset. Then, a low cost realization is required for the high speed tracking and a high
accuracy realization is desired for the precise tracking. In this paper,
the directions roughly estimated using the delayed-sum-array method
are used for the resetting. Several results of experiments performed in
an actual room environment show the effectiveness of the proposed method.
Abstract: Historical monuments as architectural heritage are,
economically and culturally, considered one of the key aspects for
modern communities. Cultural heritage represents a country-s
national identity and pride and maintains and enriches that country-s
culture. Therefore, conservation of the monuments remained from
our ancestors requires everybody-s serious and unremitting effort.
Conservation, renewal, restoration, and technical study of cultural
and historical matters are issues which have a special status among
various forms of art and science in the present century and this is due
to two reasons: firstly, progress of humankind in this century has
created a factor called environmental pollution which not only has
caused new destructive processes of cultural/historical monuments
but also has accelerated the previous destructive processes by several
times, and secondly, the rapid advance of various sciences, especially
chemistry, has lead to the contribution of new methods and materials
to this significant issue.
Abstract: In this paper, we present a preconditioned AOR-type iterative method for solving the linear systems Ax = b, where A is a Z-matrix. And give some comparison theorems to show that the rate of convergence of the preconditioned AOR-type iterative method is faster than the rate of convergence of the AOR-type iterative method.
Abstract: This paper deals optimized model to investigate the
effects of peak current, pulse on time and pulse off time in EDM performance on material removal rate of titanium alloy utilizing copper tungsten as electrode and positive polarity of the electrode. The experiments are carried out on Ti6Al4V. Experiments were
conducted by varying the peak current, pulse on time and pulse off time. A mathematical model is developed to correlate the influences of these variables and material removal rate of workpiece. Design of
experiments (DOE) method and response surface methodology
(RSM) techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through
analysis of variance (ANOVA). The obtained results evidence that as
the material removal rate increases as peak current and pulse on time
increases. The effect of pulse off time on MRR changes with peak ampere. The optimum machining conditions in favor of material removal rate are verified and compared. The optimum machining
conditions in favor of material removal rate are estimated and verified with proposed optimized results. It is observed that the developed model is within the limits of the agreeable error (about
4%) when compared to experimental results. This result leads to desirable material removal rate and economical industrial machining to optimize the input parameters.
Abstract: The study of the geometric shape of the plunging wave enclosed vortices as a possible indicator for the breaking intensity of ocean waves has been ongoing for almost 50 years with limited success. This paper investigates the validity of using the vortex ratio and vortex angle as methods of predicting breaking intensity. Previously published works on vortex parameters, based on regular wave flume results or solitary wave theory, present contradictory results and conclusions. Through the first complete analysis of field collected irregular wave breaking vortex parameters it is illustrated that the vortex ratio and vortex angle cannot be accurately predicted using standard breaking wave characteristics and hence are not suggested as a possible indicator for breaking intensity.
Abstract: Traditionally, terror groups have been formed by ideologically aligned actors who perceive a lack of options for achieving political or social change. However, terrorist attacks have been increasingly carried out by small groups of actors or lone individuals who may be only ideologically affiliated with larger, formal terrorist organizations. The formation of these groups represents the inverse of traditional organizational growth, whereby structural de-evolution within issue-based organizations leads to the formation of small, independent terror cells. Ideological franchising – the bypassing of formal affiliation to the “parent" organization – represents the de-evolution of traditional concepts of organizational structure in favor of an organic, independent, and focused unit. Traditional definitions of dark networks that are issue-based include focus on an identified goal, commitment to achieving this goal through unrestrained actions, and selection of symbolic targets. The next step in the de-evolution of small dark networks is the miniorganization, consisting of only a handful of actors working toward a common, violent goal. Information-sharing through social media platforms, coupled with civil liberties of democratic nations, provide the communication systems, access to information, and freedom of movement necessary for small dark networks to flourish without the aid of a parent organization. As attacks such as the 7/7 bombings demonstrate the effectiveness of small dark networks, terrorist actors will feel increasingly comfortable aligning with an ideology only, without formally organizing. The natural result of this de-evolving organization is the single actor event, where an individual seems to subscribe to a larger organization-s violent ideology with little or no formal ties.
Abstract: Software reliability prediction gives a great opportunity to measure the software failure rate at any point throughout system test. A software reliability prediction model provides with the technique for improving reliability. Software reliability is very important factor for estimating overall system reliability, which depends on the individual component reliabilities. It differs from hardware reliability in that it reflects the design perfection. Main reason of software reliability problems is high complexity of software. Various approaches can be used to improve the reliability of software. We focus on software reliability model in this article, assuming that there is a time redundancy, the value of which (the number of repeated transmission of basic blocks) can be an optimization parameter. We consider given mathematical model in the assumption that in the system may occur not only irreversible failures, but also a failure that can be taken as self-repairing failures that significantly affect the reliability and accuracy of information transfer. Main task of the given paper is to find a time distribution function (DF) of instructions sequence transmission, which consists of random number of basic blocks. We consider the system software unreliable; the time between adjacent failures has exponential distribution.
Abstract: The world economic crises and budget constraints
have caused authorities, especially those in developing countries, to
rationalize water quality monitoring activities. Rationalization
consists of reducing the number of monitoring sites, the number of
samples, and/or the number of water quality variables measured. The
reduction in water quality variables is usually based on correlation. If
two variables exhibit high correlation, it is an indication that some of
the information produced may be redundant. Consequently, one
variable can be discontinued, and the other continues to be measured.
Later, the ordinary least squares (OLS) regression technique is
employed to reconstitute information about discontinued variable by
using the continuously measured one as an explanatory variable. In
this paper, two record extension techniques are employed to
reconstitute information about discontinued water quality variables,
the OLS and the Line of Organic Correlation (LOC). An empirical
experiment is conducted using water quality records from the Nile
Delta water quality monitoring network in Egypt. The record
extension techniques are compared for their ability to predict
different statistical parameters of the discontinued variables. Results
show that the OLS is better at estimating individual water quality
records. However, results indicate an underestimation of the variance
in the extended records. The LOC technique is superior in preserving
characteristics of the entire distribution and avoids underestimation
of the variance. It is concluded from this study that the OLS can be
used for the substitution of missing values, while LOC is preferable
for inferring statements about the probability distribution.
Abstract: It was analyzed of fatty acid composition of 16 strains
of microalgae lipid fractions isolated from different basins of
Kazakhstan and characterized by stable active growth in the
laboratory. Three species of green microalgae (Oocystis
rhomboideus, Chlorococcum infusionum, Dictyochlorella globosa)
and three species of diatoms (Synedra sp., Nitzshia sp., Pleurosigma
attenuatum) are characterized by a high content of lipids and are
promising for further study as a source of polyunsaturated fatty acids.
Abstract: Existing literature ondesign reasoning seems to give
either one sided accounts on expert design behaviour based on
internal processing. In the same way ecological theoriesseem to
focus one sidedly on external elementsthat result in a lack of unifying
design cognition theory. Although current extended design cognition
studies acknowledge the intellectual interaction between internal and
external resources, there still seems to be insufficient understanding
of the complexities involved in such interactive processes. As
such,this paper proposes a novelmulti-directional model for design
researchers tomap the complex and dynamic conduct controlling
behaviour in which both the computational and ecological
perspectives are integrated in a vertical manner. A clear distinction
between identified intentional and emerging physical drivers, and
relationships between them during the early phases of experts- design
process, is demonstrated by presenting a case study in which the
model was employed.
Abstract: This paper looks into detailed investigation of
thermal-hydraulic characteristics of the flow field in a fuel rod
model, especially near the spacer. The area investigate represents a
source of information on the velocity flow field, vortex, and on the
amount of heat transfer into the coolant all of which are critical for
the design and improvement of the fuel rod in nuclear power plants.
The flow field investigation uses three-dimensional Computational
Fluid Dynamics (CFD) with the Reynolds stresses turbulence model
(RSM). The fuel rod model incorporates a vertical annular channel
where three different shapes of spacers are used; each spacer shape is
addressed individually. These spacers are mutually compared in
consideration of heat transfer capabilities between the coolant and
the fuel rod model. The results are complemented with the calculated
heat transfer coefficient in the location of the spacer and along the
stainless-steel pipe.
Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: According to the statistics, the prevalence of congenital hearing loss in Taiwan is approximately six thousandths; furthermore, one thousandths of infants have severe hearing impairment. Hearing ability during infancy has significant impact in the development of children-s oral expressions, language maturity, cognitive performance, education ability and social behaviors in the future. Although most children born with hearing impairment have sensorineural hearing loss, almost every child more or less still retains some residual hearing. If provided with a hearing aid or cochlear implant (a bionic ear) timely in addition to hearing speech training, even severely hearing-impaired children can still learn to talk. On the other hand, those who failed to be diagnosed and thus unable to begin hearing and speech rehabilitations on a timely manner might lose an important opportunity to live a complete and healthy life. Eventually, the lack of hearing and speaking ability will affect the development of both mental and physical functions, intelligence, and social adaptability. Not only will this problem result in an irreparable regret to the hearing-impaired child for the life time, but also create a heavy burden for the family and society. Therefore, it is necessary to establish a set of computer-assisted predictive model that can accurately detect and help diagnose newborn hearing loss so that early interventions can be provided timely to eliminate waste of medical resources. This study uses information from the neonatal database of the case hospital as the subjects, adopting two different analysis methods of using support vector machine (SVM) for model predictions and using logistic regression to conduct factor screening prior to model predictions in SVM to examine the results. The results indicate that prediction accuracy is as high as 96.43% when the factors are screened and selected through logistic regression. Hence, the model constructed in this study will have real help in clinical diagnosis for the physicians and actually beneficial to the early interventions of newborn hearing impairment.
Abstract: The major problem that wireless communication
systems undergo is multipath fading caused by scattering of the
transmitted signal. However, we can treat multipath propagation as
multiple channels between the transmitter and receiver to improve
the signal-to-scattering-noise ratio. While using Single Input
Multiple Output (SIMO) systems, the diversity receivers extract
multiple signal branches or copies of the same signal received from
different channels and apply gain combining schemes such as Root
Mean Square Gain Combining (RMSGC). RMSGC asymptotically
yields an identical performance to that of the theoretically optimal
Maximum Ratio Combining (MRC) for values of mean Signal-to-
Noise-Ratio (SNR) above a certain threshold value without the need
for SNR estimation. This paper introduces an improvement of
RMSGC using two different issues. We found that post-detection and
de-noising the received signals improve the performance of RMSGC
and lower the threshold SNR.
Abstract: This document details the process of developing a
wireless device that captures the basic movements of the foot (plantar
flexion, dorsal flexion, abduction, adduction.), and the knee
movement (flexion). It implements a motion capture system by using
a hardware based on optical fiber sensors, due to the advantages in
terms of scope, noise immunity and speed of data transmission and
reception. The operating principle used by this system is the detection
and transmission of joint movement by mechanical elements and
their respective measurement by optical ones (in this case infrared).
Likewise, Visual Basic software is used for reception, analysis and
signal processing of data acquired by the device, generating a 3D
graphical representation in real time of each movement. The result is
a boot in charge of capturing the movement, a transmission module
(Implementing Xbee Technology) and a receiver module for
receiving information and sending it to the PC for their respective
processing.
The main idea with this device is to help on topics such as
bioengineering and medicine, by helping to improve the quality of
life and movement analysis.
Abstract: It is known that the heart interacts with and adapts to
its venous and arterial loading conditions. Various experimental
studies and modeling approaches have been developed to investigate
the underlying mechanisms. This paper presents a model of the left
ventricle derived based on nonlinear stress-length myocardial
characteristics integrated over truncated ellipsoidal geometry, and
second-order dynamic mechanism for the excitation-contraction
coupling system. The results of the model presented here describe the
effects of the viscoelastic damping element of the electromechanical
coupling system on the hemodynamic response. Different heart rates
are considered to study the pacing effects on the performance of the
left-ventricle against constant preload and afterload conditions under
various damping conditions. The results indicate that the pacing
process of the left ventricle has to take into account, among other
things, the viscoelastic damping conditions of the myofilament
excitation-contraction process.
Abstract: Building intelligent traffic guide systems has been an
interesting subject recently. A good system should be able to observe
all important visual information to be able to analyze the context of
the scene. To do so, signs in general, and traffic signs in particular,
are usually taken into account as they contain rich information to
these systems. Therefore, many researchers have put an effort on
sign recognition field. Sign localization or sign detection is the most
important step in the sign recognition process. This step filters out
non informative area in the scene, and locates candidates in later
steps. In this paper, we apply a new approach in detecting sign
locations using a new color invariant model. Experiments are carried
out with different datasets introduced in other works where authors
claimed the difficulty in detecting signs under unfavorable imaging
conditions. Our method is simple, fast and most importantly it gives
a high detection rate in locating signs.
Abstract: Retention in the IT profession is critical for
organizations to stay competitive and operate reliably in the dynamic
business environment. Most organizations rely on compensation and
rewards as primary tools to enhance retention of employees. In this
quantitative survey-based study conducted at a large global bank, we
analyze the perceptions of 575 information technology (IT) software
professionals in India and Malaysia and find that fairness of rewards
has very little impact on retention likelihood. It is far more important
to actively involve employees in organizational activities. In
addition, our findings indicate that involvement is far more important
than information flow: the typical organizational communication to
keep employees informed.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: In this paper, in order to investigate the effects of
photovoltaic system introduction to detached houses in Japan, two
kinds of works were done. Firstly, the hourly generation amount of a
4.2kW photovoltaic system were simulated in 46 cities to investigate
the potential of the system in different regions in Japan using a
simulation model of photovoltaic system. Secondly, based on the
simulated electricity generation amount, the energy saving, the
environmental and the economic effect of the photovoltaic system
were examined from hourly to annual timescales, based upon
calculations of typical electricity, heating, cooling and hot water
supply load profiles for Japanese dwellings. The above analysis was
carried out using a standard year-s hourly weather data for the
different city provided by the Expanded AMeDAS Weather Data
issued by AIJ (Architectural Institute of Japan).