Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: The technical realization of data transmission using
glass fiber began after the development of diode laser in year 1962.
The erbium doped fiber amplifiers (EDFA's) in high speed networks
allow information to be transmitted over longer distances without
using of signal amplification repeaters. These kinds of fibers are
doped with erbium atoms which have energy levels in its atomic
structure for amplifying light at 1550nm. When a carried signal wave
at 1550nm enters the erbium fiber, the light stimulates the excited
erbium atoms which pumped with laser beam at 980nm as additional
light. The wavelength and intensity of the semiconductor lasers
depend on the temperature of active zone and the injection current.
The present paper shows the effect of the diode lasers temperature
and injection current on the optical amplification. From the results of
in- and output power one may calculate the max. optical gain by
erbium doped fiber amplifier.
Abstract: A method and apparatus for noninvasive measurement
of blood glucose concentration based on transilluminated laser beam
via the Index Finger has been reported in this paper. This method
depends on atomic gas (He-Ne) laser operating at 632.8nm
wavelength. During measurement, the index finger is inserted into the
glucose sensing unit, the transilluminated optical signal is converted
into an electrical signal, compared with the reference electrical
signal, and the obtained difference signal is processed by signal
processing unit which presents the results in the form of blood
glucose concentration. This method would enable the monitoring
blood glucose level of the diabetic patient continuously, safely and
noninvasively.
Abstract: In this paper, by exploiting a single semiconductor
optical amplifier-Mach Zehnder Interferometer (SOA-MZI), an
integratable all-optical flip-flop (AOFF) is proposed. It is composed
of a SOA-MZI with a bidirectional coupler at the output. Output
signals of both bar and crossbar of the SOA-MZI is fed back to SOAs
located in the arms of the Mach-Zehnder Interferometer (MZI). The
injected photon-rates to the SOAs are modulated by feedback signals
in order to form optical flip-flop. According to numerical analysis,
Gaussian optical pulses with the energy of 15.2 fJ and 20 ps duration
with the full width at half-maximum criterion, can switch the states of
the SR-AOFF. Also simulation results show that the SR-AOFF has
the contrast ratio of 8.5 dB between two states with the transition
time of nearly 20 ps.
Abstract: Infrared communication in the wavelength band 780-
950 nm is very suitable for short-range point-to-point communications.
It is a good choice for vehicle-to-vehicle communication in several
intelligent-transportation-system (ITS) applications such as cooperative
driving, collision warning, and pileup-crash prevention. In this
paper, with the aid of a physical model established in our previous
works, we explore the communication area of an infrared intervehicle
communication system utilizing a typical low-cost cormmercial lightemitting
diodes (LEDs) as the emitter and planar p-i-n photodiodes
as the receiver. The radiation pattern of the emitter fabricated by
aforementioned LEDs and the receiving pattern of the receiver are
approximated by a linear combination of cosinen functions. This
approximation helps us analyze the system performance easily. Both
multilane straight-road conditions and curved-road conditions with
various radius of curvature are taken into account. The condition of
a small car communicating with a big truck, i.e., there is a vertical
mounting height difference between the emitter and the receiver, is
also considered. Our results show that the performance of the system
meets the requirement of aforementioned ITS applications in terms
of the communication area.
Abstract: Based on a theoretical erbium-doped fiber amplifier
(EDFA) model, we have proposed an application of disturbance
observer(DOB) with proportional/integral/differential(PID) controller
to EDFA for minimizing gain-transient time of wavelength
-division-multiplexing (WDM) multi channels in optical amplifier in
channel add/drop networks. We have dramatically reduced the
gain-transient time to less than 30μsec by applying DOB with PID
controller to the control of amplifier gain. The proposed DOB-based
gain control algorithm for EDFA was implemented as a digital control
system using TI's DSP(TMS320C28346) chip and experimental
results of the system verify the excellent performance of the proposed
gain control methodology.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: Optical burst switching (OBS) has been proposed to
realize the next generation Internet based on the wavelength division
multiplexing (WDM) network technologies. In the OBS, the burst
contention is one of the major problems. The deflection routing has
been designed for resolving the problem. However, the deflection
routing becomes difficult to prevent from the burst contentions as the
network load becomes high. In this paper, we introduce a flow rate
control methods to reduce burst contentions. We propose new flow
rate control methods based on the leaky bucket algorithm and
deflection routing, i.e. separate leaky bucket deflection method, and
dynamic leaky bucket deflection method. In proposed methods, edge
nodes which generate data bursts carry out the flow rate control
protocols. In order to verify the effectiveness of the flow rate control in
OBS networks, we show that the proposed methods improve the
network utilization and reduce the burst loss probability through
computer simulations.
Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: In this paper a novel structure of metamaterial is
proposed in order to miniaturize a rectangular microstrip patch
antenna. The metamaterial is composed of two nested split octagons
which are located on a 10 mm
Abstract: In high powered dense wavelength division
multiplexed (WDM) systems with low chromatic dispersion,
four-wave mixing (FWM) can prove to be a major source of noise.
The MultiCanonical Monte Carlo Method (MCMC) and the Split
Step Fourier Method (SSFM) are combined to accurately evaluate the
probability density function of the decision variable of a receiver,
limited by FWM. The combination of the two methods leads to more
accurate results, and offers the possibility of adding other optical
noises such as the Amplified Spontaneous Emission (ASE) noise.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: Optical network uses a tool for routing which is called
Latin router. These routers use particular algorithms for routing. In this paper, we present algorithm for configuration of optical network that is optimized regarding previous algorithm. We show that by decreasing the number of hops for source-destination in lightpath number of satisfied request is less. Also we had shown that more than
single-hop lightpath relating single-hop lightpath is better.
Abstract: In the present work, an attempt is made to understand
electromagnetic field confinement in a subwavelength waveguide
structure using concepts of quantum mechanics. Evanescent field in
the waveguide is looked as inability of the photon to get confined in
the waveguide core and uncertainty of position is assigned to it. The
momentum uncertainty is calculated from position uncertainty.
Schrödinger wave equation for the photon is written by incorporating
position-momentum uncertainty. The equation is solved and field
distribution in the waveguide is obtained. The field distribution and
power confinement is compared with conventional waveguide theory.
They were found in good agreement with each other.
Abstract: METIS is the Multi Element Telescope for Imaging
and Spectroscopy, a Coronagraph aboard the European Space
Agency-s Solar Orbiter Mission aimed at the observation of the solar
corona via both VIS and UV/EUV narrow-band imaging and spectroscopy. METIS, with its multi-wavelength capabilities, will
study in detail the physical processes responsible for the corona heating and the origin and properties of the slow and fast solar wind.
METIS electronics will collect and process scientific data thanks to its detectors proximity electronics, the digital front-end subsystem
electronics and the MPPU, the Main Power and Processing Unit,
hosting a space-qualified processor, memories and some rad-hard
FPGAs acting as digital controllers.This paper reports on the overall
METIS electronics architecture and data processing capabilities
conceived to address all the scientific issues as a trade-off solution between requirements and allocated resources, just before the
Preliminary Design Review as an ESA milestone in April 2012.
Abstract: An analytical solution for dispersion of a solute in the
peristaltic motion of a couple stress fluid in the presence of magnetic
field with both homogeneous and heterogeneous chemical reactions is
presented. The average effective dispersion coefficient has been found
using Taylor-s limiting condition and long wavelength approximation.
The effects of various relevant parameters on the average effective
coefficient of dispersion have been studied. The average effective
dispersion coefficient tends to decrease with magnetic field parameter,
homogeneous chemical reaction rate parameter and amplitude ratio
but tends to increase with heterogeneous chemical reaction rate
parameter.
Abstract: We propose an all optical flip-flop circuit composedof two Silicon-on-insulator microring resonators coupled to straightwaveguides by exploiting the optical bistability behavior due to thenonlinear Kerr effect. We used the transfer matrix analysis toinvestigate continuous wave propagation through microrings, as wellwe considered the nonlinear switching characteristics of an opticaldevice using a double-coupler silicon ring resonator in presence ofthe Kerr nonlinearity, thus obtaining the bistability behavior of theoutput port, the drop port and also inside the silicon microringresonator. It is shown that the bistability behavior depends on thecontrol of the input wavelength.KeywordsAll optical flip-flops, Kerr effect, microringresonator, optical bistability.