Abstract: This paper presents a method of evaluating the effect
of aggregate angularity on hot mix asphalt (HMA) properties and its
relationship to the Permanent Deformation resistance. The research
concluded that aggregate particle angularity had a significant effect
on the Permanent Deformation performance, and also that with an
increase in coarse aggregate angularity there was an increase in the
resistance of mixes to Permanent Deformation. A comparison
between the measured data and predictive data of permanent
deformation predictive models showed the limits of existing
prediction models. The numerical analysis described the permanent
deformation zones and concluded that angularity has an effect of the
onset of these zones. Prediction of permanent deformation help road
agencies and by extension economists and engineers determine the
best approach for maintenance, rehabilitation, and new construction
works of the road infrastructure.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.
Abstract: The aim of this study is to investigate formability of
Al based closed cell metallic foams at high temperature. The foam
specimens with rectangular section were produced from
AlMg1Si0.6TiH20.8 alloy preform material. Bending and free
bending tests based on gravity effect were applied to foam specimens
at high temperatures. During the tests, the time-angular deformation
relationships with various temperatures were determined.
Deformation types formed in cell walls were investigated by means
of Scanning Electron Microscopy (SEM) and optical microscopy.
Bending deformation about 90° was achieved without any defect at
high temperatures. The importance of a critical temperature and
deformation rate was emphasized in maintaining the deformation.
Significant slip lines on surface of cell walls at tensile zones of
bending specimen were observed. At high strain rates, the microcrack
formation in boundaries of elongated grains was determined.
Abstract: Image compression based on fractal coding is a lossy
compression method and normally used for gray level images range
and domain blocks in rectangular shape. Fractal based digital image
compression technique provide a large compression ratio and in this
paper, it is proposed using YUV colour space and the fractal theory
which is based on iterated transformation. Fractal geometry is mainly
applied in the current study towards colour image compression
coding. These colour images possesses correlations among the colour
components and hence high compression ratio can be achieved by
exploiting all these redundancies. The proposed method utilises the
self-similarity in the colour image as well as the cross-correlations
between them. Experimental results show that the greater
compression ratio can be achieved with large domain blocks but more
trade off in image quality is good to acceptable at less than 1 bit per
pixel.
Abstract: In this paper, a numerical simulation of a finned store
separating from a wing-pylon configuration has been studied and
validated. A dynamic unstructured tetrahedral mesh approach is
accomplished by using three grid sizes to numerically solving the
discretized three dimensional, inviscid and compressible Euler
equations. The method used for computations of separation of an
external store assuming quasi-steady flow condition. Computations of
quasi-steady flow have been directly coupled to a six degree-offreedom
(6DOF) rigid-body motion code to generate store
trajectories. The pressure coefficients at four different angular cuts
and time histories of various trajectory parameters and wing pressure
distribution during the store separation are compared for every grid
size with published experimental data.
Abstract: Experimental study of natural convection heat transfer
inside smooth and rough surfaces of vertical and inclined equilateral
triangular channels of different inclination angles with a uniformly
heated surface are performed. The inclination angle is changed from
15º to 90º. Smooth and rough surface of average roughness (0.02mm)
are used and their effect on the heat transfer characteristics are
studied. The local and average heat transfer coefficients and Nusselt
number are obtained for smooth and rough channels at different heat
flux values, different inclination angles and different Rayleigh
numbers (Ra) 6.48 × 105 ≤ Ra ≤ 4.78 × 106. The results show that
the local Nusselt number decreases with increase of axial distance
from the lower end of the triangular channel to a point near the upper
end of channel, and then, it slightly increases. Higher values of local
Nusselt number for rough channel along the axial distance compared
with the smooth channel. The average Nusselt number of rough
channel is higher than that of smooth channel by about 8.1% for
inclined case at θ = 45o and 10% for vertical case. The results
obtained are correlated using dimensionless groups for both rough
and smooth surfaces of the inclined and vertical triangular channels.
Abstract: The hydrodynamics and heat transfer characteristics
of a vaporized elongated bubble in a rectangular microchannel have
been simulated based on Cahn-Hilliard phase-field method. In the
simulations, the initially nucleated bubble starts growing as it comes
in contact with superheated water. The growing shape of the bubble
compared well with the available experimental data in the literature.
Abstract: Fixed-geometry hydrodynamic journal bearings are
one of the best supporting systems for several applications of rotating
machinery. Cylindrical journal bearings present excellent loadcarrying
capacity and low manufacturing costs, but they are subjected
to the oil-film instability at high speeds. An attempt of overcoming
this instability problem has been the development of non-circular
journal bearings. This work deals with an analysis of oil-lubricated
elliptical journal bearings using the finite element method. Steadystate
and dynamic performance characteristics of elliptical bearings
are rendered by zeroth- and first-order lubrication equations obtained
through a linearized perturbation method applied on the classical
Reynolds equation. Four-node isoparametric rectangular finite
elements are employed to model the bearing thin film flow. Curves of
elliptical bearing load capacity and dynamic force coefficients are
rendered at several operating conditions. The results presented in this
work demonstrate the influence of the bearing ellipticity on its
performance at different loading conditions.
Abstract: This paper presents two techniques, local feature
extraction using image spectrum and low frequency spectrum
modelling using GMM to capture the underlying statistical
information to improve the performance of face recognition
system. Local spectrum features are extracted using overlap sub
block window that are mapped on the face image. For each of this
block, spatial domain is transformed to frequency domain using
DFT. A low frequency coefficient is preserved by discarding high
frequency coefficients by applying rectangular mask on the
spectrum of the facial image. Low frequency information is non-
Gaussian in the feature space and by using combination of several
Gaussian functions that has different statistical properties, the best
feature representation can be modelled using probability density
function. The recognition process is performed using maximum
likelihood value computed using pre-calculated GMM components.
The method is tested using FERET datasets and is able to achieved
92% recognition rates.
Abstract: This paper presents Finite Element Method (FEM) for
analyzing the internal responses generated in thin rectangular plates
with various edge conditions and rigidity conditions. Comparison has
been made between the FEM (ANSYS software) results for
displacement, stresses and moments generated with and without the
consideration of hole in plate and different aspect ratios. In the end
comparison for responses in plain and composite square plates has
been studied.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: A compact UWB planar antenna fed with a
microstrip-line is proposed. The new design consist of a rectangular
patch with symmetric l-shaped slots and fed by 50 Ω microstrip
transmission line and a reduced ground-plane which have a periodic
slots with an overall size of 47 mm x 20 mm. It is intended to be used
in wireless applications that cover the ultra-wideband (UWB)
frequency band. A wider impedance bandwidth of around 116.5%
(1.875 – 7.115 GHz) with stable radiation pattern is achieved. The
proposed antenna has excellent characteristics, low profile and costeffective
compared to existing UWB antennas. The UWB antenna is
designed and analyzed using CST Microwave Studio in transient
mode to verify antenna parameters improvements.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: In the present study, mixed convection in a horizontal
rectangular duct using Al2O3 is numerically investigated. The effects
of different Rayleigh number, Reynolds number and radiation on
flow and heat transfer characteristics are studied in detail. This study
covers Rayleigh number in the range of 2 × 10^6 ≤ Ra ≤ 2 × 10^7 and
Reynolds number in the range of 100 ≤ Re ≤ 1100. Results reveal that
the Nusselt number increases as Reynolds and Rayleigh numbers
increase. It is also found that the dimensionless temperature
distribution increases as Rayleigh number increases.