Abstract: The paper presents a one-dimensional transient
mathematical model of compressible non-isothermal multicomponent
fluid mixture flow in a pipe. The set of the mass,
momentum and enthalpy conservation equations for gas phase is
solved in the model. Thermo-physical properties of multi-component
gas mixture are calculated by solving the Equation of State (EOS)
model. The Soave-Redlich-Kwong (SRK-EOS) model is chosen. Gas
mixture viscosity is calculated on the basis of the Lee-Gonzales-
Eakin (LGE) correlation. Numerical analysis of rapid gas
decompression process in rich and base natural gases is made on the
basis of the proposed mathematical model. The model is successfully
validated on the experimental data [1]. The proposed mathematical
model shows a very good agreement with the experimental data [1] in
a wide range of pressure values and predicts the decompression in
rich and base gas mixtures much better than analytical and
mathematical models, which are available from the open source
literature.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: Web sites are rapidly becoming the preferred media
choice for our daily works such as information search, company
presentation, shopping, and so on. At the same time, we live in a
period where visual appearances play an increasingly important
role in our daily life. In spite of designers- effort to develop a web
site which be both user-friendly and attractive, it would be difficult
to ensure the outcome-s aesthetic quality, since the visual
appearance is a matter of an individual self perception and opinion.
In this study, it is attempted to develop an automatic system for
web pages aesthetic evaluation which are the building blocks of
web sites. Based on the image processing techniques and artificial
neural networks, the proposed method would be able to categorize
the input web page according to its visual appearance and aesthetic
quality. The employed features are multiscale/multidirectional
textural and perceptual color properties of the web pages, fed to
perceptron ANN which has been trained as the evaluator. The
method is tested using university web sites and the results
suggested that it would perform well in the web page aesthetic
evaluation tasks with around 90% correct categorization.
Abstract: Mechanical and water transport properties of high
performance concrete (HPC) containing natural zeolite as partial
replacement of Portland cement are studied. Experimental results
show that in the investigated mixes the use of natural zeolite leads to
an increase of porosity, decrease of compressive strength and
increase of moisture diffusivity and water vapor diffusion coefficient,
as compared with the reference HPC. However, for the replacement
level up to 20% of the mass of Portland cement the concretes still
maintain their high performance character and exhibit acceptable
water transport properties. Therefore, natural zeolite can be
considered an environmental friendly binder with a potential to
replace a part of Portland cement in concrete in building industry.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: Soft topological spaces are considered as mathematical tools for dealing with uncertainties, and a fuzzy topological space is a special case of the soft topological space. The purpose of this paper is to study soft topological spaces. We introduce some new concepts in soft topological spaces such as soft first-countable spaces, soft second-countable spaces and soft separable spaces, and some basic properties of these concepts are explored.
Abstract: Camera calibration plays an important role in the domain of the analysis of sports video. Considering soccer video, in most cases, the cross-points can be used for calibration at the center of the soccer field are not sufficient, so this paper introduces a new automatic camera calibration algorithm focus on solving this problem by using the properties of images of the center circle, halfway line and a touch line. After the theoretical analysis, a practicable automatic algorithm is proposed. Very little information used though, results of experiments with both synthetic data and real data show that the algorithm is applicable.
Abstract: Let Gα ,β (γ ,δ ) denote the class of function
f (z), f (0) = f ′(0)−1= 0 which satisfied e δ {αf ′(z)+ βzf ′′(z)}> γ i Re
in the open unit disk D = {z ∈ı : z < 1} for some α ∈ı (α ≠ 0) ,
β ∈ı and γ ∈ı (0 ≤γ 0 . In
this paper, we determine some extremal properties including
distortion theorem and argument of f ′( z ) .
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free and clamped-clamped boundary conditions.
Abstract: The effects of irrigation with dairy factory wastewater on soil properties were investigated at two sites that had received irrigation for > 60 years. Two adjoining paired sites that had never received DFE were also sampled as well as another seven fields from a wider area around the factory. In comparison with paired sites that had not received effluent, long-term wastewater irrigation resulted in an increase in pH, EC, extractable P, exchangeable Na and K and ESP. These changes were related to the use of phosphoric acid, NaOH and KOH as cleaning agents in the factory. Soil organic C content was unaffected by DFE irrigation but the size (microbial biomass C and N) and activity (basal respiration) of the soil microbial community were increased. These increases were attributed to regular inputs of soluble C (e.g. lactose) present as milk residues in the wastewater. Principal component analysis (PCA) of the soils data from all 11sites confirmed that the main effects of DFE irrigation were an increase in exchangeable Na, extractable P and microbial biomass C, an accumulation of soluble salts and a liming effect. PCA analysis of soil bacterial community structure, using PCR-DGGE of 16S rDNA fragments, generally separated individual sites from one another but did not group them according to irrigation history. Thus, whilst the size and activity of the soil microbial community were increased, the structure and diversity of the bacterial community remained unaffected.
Abstract: Honeycomb sandwich panels are increasingly used in the construction of space vehicles because of their outstanding strength, stiffness and light weight properties. However, the use of honeycomb sandwich plates comes with difficulties in the design process as a result of the large number of design variables involved, including composite material design, shape and geometry. Hence, this work deals with the presentation of an optimal design of hexagonal honeycomb sandwich structures subjected to space environment. The optimization process is performed using a set of algorithms including the gravitational search algorithm (GSA). Numerical results are obtained and presented for a set of algorithms. The results obtained by the GSA algorithm are much better compared to other algorithms used in this study.
Abstract: This study fabricates p-type Ni1−xO:Li/n-Si heterojunction solar cells (P+/n HJSCs) by using radio frequency (RF) magnetron sputtering and investigates the effect of substrate temperature on photovoltaic cell properties. Grazing incidence x-ray diffraction, four point probe, and ultraviolet-visible-near infrared discover the optoelectrical properties of p-Ni1-xO thin films. The results show that p-Ni1-xO thin films deposited at 300 oC has the highest grain size (22.4 nm), average visible transmittance (~42%), and electrical resistivity (2.7 Ωcm). However, the conversion efficiency of cell is shown only 2.33% which is lower than the cell (3.39%) fabricated at room temperature. This result can be mainly attributed to interfacial layer thickness (SiOx) reduces from 2.35 nm to 1.70 nm, as verified by high-resolution transmission electron microscopy.
Abstract: Starting from the basic pillars of the supportability
analysis this paper queries its characteristics in LCI (Life Cycle
Integration) environment. The research methodology contents a
review of modern logistics engineering literature with the objective to
collect and synthesize the knowledge relating to standards of
supportability design in e-logistics environment. The results show
that LCI framework has properties which are in fully compatibility
with the requirement of simultaneous logistics support and productservice
bundle design. The proposed approach is a contribution to the
more comprehensive and efficient supportability design process.
Also, contributions are reflected through a greater consistency of
collected data, automated creation of reports suitable for different
analysis, as well as the possibility of their customization according
with customer needs. In addition to this, convenience of this approach
is its practical use in real time. In a broader sense, LCI allows
integration of enterprises on a worldwide basis facilitating electronic
business.
Abstract: A numerical method is proposed to calculate damping
properties for sound-proof structures involving elastic body,
viscoelastic body, and porous media. For elastic and viscoelastic body
displacement is modeled using conventional finite elements including
complex modulus of elasticity. Both effective density and bulk
modulus have complex quantities to represent damped sound fields in
the porous media. Particle displacement in the porous media is
discretised using finite element method. Displacement vectors as
common unknown variables are solved under coupled condition
between elastic body, viscoelastic body and porous media. Further,
explicit expressions of modal loss factor for the mixed structures are
derived using asymptotic method. Eigenvalue analysis and frequency
responded were calculated for automotive test panel laminated
viscoelastic and porous structures using this technique, the results
almost agreed with the experimental results.
Abstract: In this paper, the application of the Mode Matching
(MM) method in the case of photonic crystal waveguide
discontinuities is presented. The structure under consideration is
divided into a number of cells, which supports a number of guided
and evanescent modes. These modes can be calculated numerically
by an alternative formulation of the plane wave expansion method
for each frequency. A matrix equation is then formed relating the
modal amplitudes at the beginning and at the end of the structure.
The theory is highly efficient and accurate and can be applied to
study the transmission sensitivity of photonic crystal devices due to
fabrication tolerances. The accuracy of the MM method is compared
to the Finite Difference Frequency Domain (FDFD) and the Adjoint
Variable Method (AVM) and good agreement is observed.
Abstract: The previous researches focused on the influence of
anthropogenic greenhouse gases exerting global warming, but not
consider whether desert sand may warm the planet, this could be
improved by accounting for sand's physical and geometric properties.
Here we show, sand particles (because of their geometry) at the desert
surface form an extended surface of up to 1 + π/4 times the planar area
of the desert that can contact sunlight, and at shallow depths of the
desert form another extended surface of at least 1 + π times the planar
area that can contact air. Based on this feature, an enhanced heat
exchange system between sunlight, desert sand, and air in the spaces
between sand particles could be built up automatically, which can
increase capture of solar energy, leading to rapid heating of the sand
particles, and then the heating of sand particles will dramatically heat
the air between sand particles. The thermodynamics of deserts may
thus have contributed to global warming, especially significant to
future global warming if the current desertification continues to
expand.
Abstract: In this paper, the absorption and fluorescence
emission spectra of Yb:Y3Al5O12 (YAG)(25 at%) crystal as a disk
laser medium are measured at high temperature (300-450K). The
absorption and emission cross sections of Yb:YAG crystal are
determined using Reciprocity method. Temperature dependence of
941nm absorption cross section and 1031nm emission cross section
is extracted in the range of 300-450K. According to our experimental
results, an exponential temperature dependence between 300K and
450K is acquired for the 1031nm peak emission cross section and
also for 941nm peak absorption cross section of Yb:YAG crystal.
These results could be used for simulation and design of high power
highly doped Yb:YAG thin disk lasers.
Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: The objective of this study is to investigate the effect of adding coal to obtain insulating ceramic product. The preparation of mixtures is achieved with 04 types of different masse compositions, consisting of gray and yellow clay, and coal. Analyses are performed on local raw materials by adding coal as additive. The coal content varies from 5 to 20 % in weight by varying the size of coal particles ranging from 0.25mm to 1.60mm.
Initially, each natural moisture content of a raw material has been determined at the temperature of 105°C in a laboratory oven. The Influence of low-coal content on absorption, the apparent density, the contraction and the resistance during compression have been evaluated. The experimental results showed that the optimized composition could be obtained by adding 10% by weight of coal leading thus to insulating ceramic products with water absorption, a density and resistance to compression of 9.40 %, 1.88 g/cm3, 35.46 MPa, respectively. The results show that coal, when mixed with traditional raw materials, offers the conditions to be used as an additive in the production of lightweight ceramic products.
Abstract: α-Pinene is the main component of the most
turpentine oils. The hydration of α-pinene with acid catalysts leads to
a complex mixture of monoterpenes. In order to obtain more valuable
products, the α-pinene in the turpentine can be hydrated in dilute
mineral acid solutions to produce α-terpineol. The design of
separation processes requires information on phase equilibrium and
related thermodynamic properties. This paper reports the results of
study on liquid-liquid equilibrium (LLE) of system containing α-
pinene + water and α-terpineol + water.
Binary LLE for α-pinene + water system, and α-terpineol + water
systems were determined by experiment at 301K and atmospheric
pressure. The two component mixture was stirred for about 30min,
then the mixture was left for about 2h for complete phase separation.
The composition of both phases was analyzed by using a Gas
Chromatograph. The experimental data were correlated by
considering both NRTL and UNIQUAC activity coefficient models.
The LLE data for the system of α-pinene + water and α-terpineol +
water were correlated successfully by the NRTL model. The
experimental data were not satisfactorily fitted by the UNIQUAC
model. The NRTL model (α =0.3) correlates the LLE data for the
system of α-pinene + water at 301K with RMSD of 0.0404%. And
the NRTL model (α =0.61) at 301K with RMSD of 0.0058 %. The
NRTL model (α =0.3) correlates the LLE data for the system of α-
terpineol + water at 301K with RMSD of 0.1487% and the NRTL
model (α =0.6) at 301K with RMSD of 0.0032%, between the
experimental and calculated mole fractions.