Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: The whole work is based on possibility to use Lego Mindstorms robotics systems to reduce costs. Lego Mindstorms consists of a wide variety of hardware components necessary to simulate, programme and test of robotics systems in practice. To programme algorithm, which simulates space using the ultrasonic sensor, was used development environment supplied with kit. Software Matlab was used to render values afterwards they were measured by ultrasonic sensor. The algorithm created for this paper uses theoretical knowledge from area of signal processing. Data being processed by algorithm are collected by ultrasonic sensor that scans 2D space in front of it. Ultrasonic sensor is placed on moving arm of robot which provides horizontal moving of sensor. Vertical movement of sensor is provided by wheel drive. The robot follows map in order to get correct positioning of measured data. Based on discovered facts it is possible to consider Lego Mindstorm for low-cost and capable kit for real-time modelling.
Abstract: An international cooperation between educators in
Australia and the US has led to a reconceptualization of the teaching
of a library science course at Appalachian State University. The
pedagogy of Action Learning coupled with a 3D virtual learning
environment immerses students in a social constructivist learning
space that incorporates and supports interaction and reflection. The
intent of this study was to build a bridge between theory and practice
by providing students with a tool set that promoted personal and
social reflection, and created and scaffolded a community of practice.
Besides, action learning is an educational process whereby the fifty
graduate students experienced their own actions and experience to
improve performance.
Abstract: A complex valued neural network is a neural network, which consists of complex valued input and/or weights and/or thresholds and/or activation functions. Complex-valued neural networks have been widening the scope of applications not only in electronics and informatics, but also in social systems. One of the most important applications of the complex valued neural network is in image and vision processing. In Neural networks, radial basis functions are often used for interpolation in multidimensional space. A Radial Basis function is a function, which has built into it a distance criterion with respect to a centre. Radial basis functions have often been applied in the area of neural networks where they may be used as a replacement for the sigmoid hidden layer transfer characteristic in multi-layer perceptron. This paper aims to present exhaustive results of using RBF units in a complex-valued neural network model that uses the back-propagation algorithm (called 'Complex-BP') for learning. Our experiments results demonstrate the effectiveness of a Radial basis function in a complex valued neural network in image recognition over a real valued neural network. We have studied and stated various observations like effect of learning rates, ranges of the initial weights randomly selected, error functions used and number of iterations for the convergence of error on a neural network model with RBF units. Some inherent properties of this complex back propagation algorithm are also studied and discussed.
Abstract: Molodstov-s soft sets theory was originally proposed
as general mathematical tool for dealing with uncertainty problems. The matrix form has been introduced in soft set and some of its
properties have been discussed. However, the formulation of soft
matrix in group decision making problem only with equal importance
weights of criteria, which does not show the true opinion of decision maker on each criteria. The aim of this paper is to propose a method
for solving group decision making problem incorporating the importance of criteria by using soft matrices in a more objective manner. The weight of each criterion is calculated by using the Analytic Hierarchy Process (AHP) method. An example of house
selection process is given to illustrate the effectiveness of the proposed method.
Abstract: In this paper, an ultra low power and low jitter 12bit
CMOS digitally controlled oscillator (DCO) design is presented.
Based on a ring oscillator implemented with low power Schmitt
trigger based inverters. Simulation of the proposed DCO using 32nm
CMOS Predictive Transistor Model (PTM) achieves controllable
frequency range of 550MHz~830MHz with a wide linearity and high
resolution. Monte Carlo simulation demonstrates that the time-period
jitter due to random power supply fluctuation is under 31ps and the
power consumption is 0.5677mW at 750MHz with 1.2V power
supply and 0.53-ps resolution. The proposed DCO has a good
robustness to voltage and temperature variations and better linearity
comparing to the conventional design.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Development of intelligent assembly cell conception includes new solution kind of how to create structures of automated and flexible assembly system. The current trend of the final product quality increasing is affected by time analysis of the entire manufacturing process. The primary requirement of manufacturing is to produce as many products as soon as possible, at the lowest possible cost, but of course with the highest quality. Such requirements may be satisfied only if all the elements entering and affecting the production cycle are in a fully functional condition. These elements consist of sensory equipment and intelligent control elements that are essential for building intelligent manufacturing systems. Intelligent behavior of the system as the control system will repose on monitoring of important parameters of the system in the real time. Intelligent manufacturing system itself should be a system that can flexibly respond to changes in entering and exiting the process in interaction with the surroundings.
Abstract: The paper presents the case study of hazard
identification and sensitivity of potential resource of emergency
water supply as part of the application of methodology classifying
the resources of drinking water for emergency supply of population.
The case study has been carried out on a selected resource of
emergency water supply in one region of the Czech Republic. The
hazard identification and sensitivity of potential resource of
emergency water supply is based on a unique procedure and
developed general registers of selected types of hazards and
sensitivities. The registers have been developed with the help of the
“Fault Tree Analysis” method in combination with the “What if
method”. The identified hazards for the assessed resource include
hailstorms and torrential rains, drought, soil erosion, accidents of
farm machinery, and agricultural production. The developed registers
of hazards and vulnerabilities and a semi-quantitative assessment of
hazards for individual parts of hydrological structure and
technological elements of presented drilled wells are the basis for a
semi-quantitative risk assessment of potential resource of emergency
supply of population and the subsequent classification of such
resource within the system of crisis planning.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: A novel algorithm for construct a seamless video mosaic of the entire panorama continuously by automatically analyzing and managing feature points, including management of quantity and quality, from the sequence is presented. Since a video contains significant redundancy, so that not all consecutive video images are required to create a mosaic. Only some key images need to be selected. Meanwhile, feature-based methods for mosaicing rely on correction of feature points? correspondence deeply, and if the key images have large frame interval, the mosaic will often be interrupted by the scarcity of corresponding feature points. A unique character of the method is its ability to handle all the problems above in video mosaicing. Experiments have been performed under various conditions, the results show that our method could achieve fast and accurate video mosaic construction. Keywords?video mosaic, feature points management, homography estimation.
Abstract: Cassava is one of the top five crops in Cameroon. Its
evolution has remained constant since the independence period and
the production has more than tripled. It is a crop with multiple
industrial capacities but the sector-s business opportunities are
underexploited. Using Strengths, Weaknesses, Opportunities and
Threats analysis method, this paper examines the cassava actual state.
It appraises the sector-s strengths (S), considers suitable measures to
strengthen weaknesses (W), evaluates strategies to fully benefit from
the sector numerous business opportunities (O) and explore means to
convert threats (T) into opportunities. Data were collected from the
ministry of agriculture and rural development and different actors.
The results show that cassava sector embodies many business
opportunities and stands as a raw material provider for many
industries but ultimately requires challenges to be tackled
appropriately.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: From the beginning of creation, human being has ever
fought against the ecosystem by changes has made in environment.
The most environmental changes on the nature have been done after
starting the concentrated life in the same region. Dams are one of the
most important buildings in water resources and transferring. These
buildings have been made from old times without access to
hydrological, hydraulically, hydro mechanical information. Dams
have positive and negative effects on environment. Constructing a
dam relatively causes equal ecological consequences. According to
different criteria, environmental effects of dams can lead short term
and long term damages. These effects may influence on the situation
and treatment of meteorology, biology, culture, ancient works, etc
and severely causes to change and complicate it. So considering
importance of positive effects of dam construction, it is necessary to
minimize negative environmental effects of dams to achieve a stable
development. In this article the considered effects and their solutions
in influencing on assessment of destructive environmental effects of
dams construction have been surveyed and presented.
Abstract: the purpose of this research is to identify and clarify
factors which have positive effect among user satisfaction and their
social networking through websites. The examined factors in this
research are; innovation, ease of use, trustworthy and customer
support which are defined as satisfaction factors. To obtain reliable
research approaches and to have better result in this research four
hypothesizes used to test. This hypothesis testing has been done by
correlation, regression and test of normality by using “SPSS16" also
the data which was analyzed by this software. this data was gathered
from prepaid questionnaire.
Abstract: From environmental aspect purification of ammonia
containing wastewater is expected. High efficiency ammonia
desorption can be done from the water by air on proper temperature.
After the desorption process, ammonia can be recovered and used in
another technology. The calculation method described below give
some methods to find either the minimum column height or ammonia
rich solution of the effluent.
Abstract: The use of e-business in small and medium-sized
enterprises (SMEs) has been recently received an enormous attention
in information systems research by both academic and practitioners.
With the adoption of new and efficient technologies to enhance
businesses, Thai SMEs should be able to compete worldwide.
Unfortunately, most of the owners are not used to new technologies.
It is clear that most Thai SMEs prefer to work manually rather than
electronically. This paper aims to provide a fundamental conceptual
framework for E-business adoption by Thai SMEs. Rooted in
Knowledge transfer model, several factors are identified, which drive
and enable e-business adoption. By overlooking the benefits
associated with implementing new technologies, it is difficult for
Thai SMEs to perform well enough to compete globally. The paper
also helps Thai SMEs to understand factors related to E-business
adoption.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.