Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: With the resource exhaustion, bad affections of human
activities and the awakening of the human rights, the corporate social
responsibility became popular corporate strategy achieving
sustainable development of both corporation and society. The issue of
Guideline of Chinese Corporate Social Responsibility Report
promotes greatly corporation to take social responsibility. This paper
built the index system according to this guideline and takes the textile
industry as an example, uses the analytical hierarchy process to
identify the weightings of different responsibilities of corporation to
guide the corporate social responsibility performance assessment.
Abstract: This paper explores an application of an adaptive learning mechanism for robots based on the natural immune system. Most of the research carried out so far are based either on the innate or adaptive characteristics of the immune system, we present a combination of these to achieve behavior arbitration wherein a robot learns to detect vulnerable areas of a track and adapts to the required speed over such portions. The test bed comprises of two Lego robots deployed simultaneously on two predefined near concentric tracks with the outer robot capable of helping the inner one when it misaligns. The helper robot works in a damage-control mode by realigning itself to guide the other robot back onto its track. The panic-stricken robot records the conditions under which it was misaligned and learns to detect and adapt under similar conditions thereby making the overall system immune to such failures.
Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: Most of the biclustering/projected clustering algorithms are based either on the Euclidean distance or correlation coefficient which capture only linear relationships. However, in many applications, like gene expression data and word-document data, non linear relationships may exist between the objects. Mutual Information between two variables provides a more general criterion to investigate dependencies amongst variables. In this paper, we improve upon our previous algorithm that uses mutual information for biclustering in terms of computation time and also the type of clusters identified. The algorithm is able to find biclusters with mixed relationships and is faster than the previous one. To the best of our knowledge, none of the other existing algorithms for biclustering have used mutual information as a similarity measure. We present the experimental results on synthetic data as well as on the yeast expression data. Biclusters on the yeast data were found to be biologically and statistically significant using GO Tool Box and FuncAssociate.
Abstract: This study focused on arsenate removal by nano
zero-valent iron (NZVI) in the gas-bubbled aqueous solution. It
appears that solution acidified by H2SO4 is far more favorable than by
CO2-bubbled acidification. In addition, as dissolved oxygen was
stripped out of solution by N2 gas bubbling, the arsenate removal
dropped significantly. To take advantages of common practice of
carbonation and oxic condition, pretreatment of CO2 and air bubbling
in sequence are recommended for a better removal of arsenate.
Abstract: The survival of publicly listed companies largely
depends on their stocks being liquidly traded. This goal can be
achieved when new investors are attracted to invest on companies-
stocks. Among different groups of investors, individual investors are
generally less able to objectively evaluate companies- risks and
returns, and tend to be emotionally biased in their investing
decisions. Therefore their decisions may be formed as a result of
perceived risks and returns, and influenced by companies- images.
This study finds that perceived risk, perceived returns and trust
directly affect individual investors- trading decisions while attitude
towards brand partially mediates the relationships. This finding
suggests that, in courting individual investors, companies still need to
perform financially while building a good image can result in their
stocks being accepted quicker than the stocks of good performing
companies with hidden images.
Abstract: The whole-cell protein-profiling technique was
evaluated for studying differences in banding pattern of three
different species of Cyanobacteria i.e. Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica under the influence
of four different pesticides-2,4-D (Ethyl Ester of 2,4-Dichloro
Phenoxy Acetic Acid), Pencycuron (N-[(4-chlorophenyl)methyl]-Ncyclopentyl-
N'–phenylurea), Endosulfan (6,7,8,9,10,10hexachloro-
1,5,5a,6,9,9a-hexahydro-6,9-methano-2,4,3-benzodioxathiepine-3-
oxide) and Tebuconazole (1-(4-Chlorophenyl)-4,4-dimethyl-3-(1,2,4-
triazol-1-ylmethyl)pentan-3-ol). Whole-cell extracts were obtained by
sonication treatment (Sonifier cell disruptor -Branson Digital Sonifier
S-450D, USA) and were analyzed by sodium dodecyl sulfate
polyacrylamide gel electrophoresis (SDS-PAGE). SDS-PAGE
analyses of the total protein profile of Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica showed a linear
decrease in the protein content with increasing pesticide stress when
administered to different concentrations of 2, 4-D, Pencycuron,
Endosulfan and Tebuconazole. The results indicate that different
stressors exert specific effects on cyanobacterial protein synthesis.
Abstract: Representation and description of object shapes by the
slopes of their contours or borders are proposed. The idea is to capture
the essence of the features that make it easier for a shape to be
stored, transmitted, compared and recognized. These features must
be independent of translation, rotation and scaling of the shape. A
approach is proposed to obtain high performance, efficiency and to
merge the boundaries into sequence of straight line segments with
the fewest possible segments. Evaluation on the performance of the
proposed method is based on its comparison with established method
of object shape description.
Abstract: Protection of slope and embankment from erosion has
become an important issue in Bangladesh. The constructions of
strong structures require large capital, integrated designing, high
maintenance cost. Strong structure methods have negative impact on
the environment and sometimes not function for the design period.
Plantation of vetiver system along the slopes is an alternative
solution. Vetiver not only serves the purpose of slope protection but
also adds green environment reducing pollution. Vetiver is available
in almost all the districts of Bangladesh. This paper presents the
application of vetiver system with geo-jute, for slope protection and
erosion control of embankments and slopes. In-situ shear tests have
been conducted on vetiver rooted soil system to find the shear
strength. The shear strength and effective soil cohesion of vetiver
rooted soil matrix are respectively 2.0 times and 2.1 times higher than
that of the bared soil. Similar trends have been found in direct shear
tests conducted on laboratory reconstituted samples. Field trials have
been conducted in road embankment and slope protection with
vetiver at different sites. During the time of vetiver root growth the
soil protection has been accomplished by geo-jute. As the geo-jute
degrades with time, vetiver roots grow and take over the function of
geo-jutes. Slope stability analyses showed that vegetation increase
the factor of safety significantly.
Abstract: In contrast to conventional generators, self-excited induction generators are found to be most suitable machines for wind energy conversion in remote and windy areas due to many advantages over grid connected machines. This papers presents a Self-Excited Induction Generator (SEIG) driven by wind turbine and supplying an induction motor which is coupled to a centrifugal pump. A method to describe the steady state performance based on nodal analysis is presented. Therefore the advanced knowledge of the minimum excitation capacitor value is required. The effects of variation of excitation capacitance on system and rotor speed under different loading conditions have been analyzed and considered to optimize induction motor pump performances.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: This paper presents a robust proportionalderivative
(PD) based cerebellar model articulation
controller (CMAC) for vertical take-off and landing flight
control systems. Successful on-line training and recalling
process of CMAC accompanying the PD controller is
developed. The advantage of the proposed method is mainly
the robust tracking performance against aerodynamic
parametric variation and external wind gust. The
effectiveness of the proposed algorithm is validated through
the application of a vertical takeoff and landing aircraft
control system.
Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.
Abstract: In this paper, FinFET devices are analyzed with
emphasis on sub-threshold leakage current control. This is achieved
through proper biasing of the back gate, and through the use of
asymmetric work functions for the four terminal FinFET devices. We
are also examining different configurations of multiplexers and XOR
gates using transistors of symmetric and asymmetric work functions.
Based on extensive characterization data for MUX circuits, our
proposed configuration using symmetric devices lead to leakage
current and delay improvements of 65% and 47% respectively
compared to results in the literature. For XOR gates, a 90%
improvement in the average leakage current is achieved by using
asymmetric devices. All simulations are based on a 25nm FinFET
technology using the University of Florida UFDG model.
Abstract: Sinc-collocation scheme is one of the new techniques
used in solving numerical problems involving integral equations. This
method has been shown to be a powerful numerical tool for finding
fast and accurate solutions. So, in this paper, some properties of the
Sinc-collocation method required for our subsequent development
are given and are utilized to reduce integral equation of the first
kind to some algebraic equations. Then convergence with exponential
rate is proved by a theorem to guarantee applicability of numerical
technique. Finally, numerical examples are included to demonstrate
the validity and applicability of the technique.
Abstract: Calcium [Ca2+] dynamics is studied as a potential form
of neuron excitability that can control many irregular processes like
metabolism, secretion etc. Ca2+ ion enters presynaptic terminal and
increases the synaptic strength and thus triggers the neurotransmitter
release. The modeling and analysis of calcium dynamics in neuron
cell becomes necessary for deeper understanding of the processes
involved. A mathematical model has been developed for cylindrical
shaped neuron cell by incorporating physiological parameters like
buffer, diffusion coefficient, and association rate. Appropriate initial
and boundary conditions have been framed. The closed form solution
has been developed in terms of modified Bessel function. A computer
program has been developed in MATLAB 7.11 for the whole
approach.
Abstract: In this paper, the effect of transmission codes on the
performance of coherent square M-ary quadrature amplitude
modulation (CSMQAM) under hybrid selection/maximal-ratio
combining (H-S/MRC) diversity is analysed. The fading channels are
modeled as frequency non-selective slow independent and identically
distributed Rayleigh fading channels corrupted by additive white
Gaussian noise (AWGN). The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM under H-S/MRC diversity by
plotting error probabilities versus average signal to noise ratio (SNR)
for various values L and N in order to examine the improvement in
the performance of the digital communications system as the number
of selected diversity branches is increased. The results for no
diversity, conventional SC and Lth order MRC schemes are also
plotted for comparison. Closed form analytical results derived in this
paper are sufficiently simple and therefore can be computed
numerically without any approximations. The analytical results
presented in this paper are expected to provide useful information
needed for design and analysis of digital communication systems
over wireless fading channels.
Abstract: There are two major variants of the Simplex
Algorithm: the revised method and the standard, or tableau method.
Today, all serious implementations are based on the revised method
because it is more efficient for sparse linear programming problems.
Moreover, there are a number of applications that lead to dense linear
problems so our aim in this paper is to present some computational
results on parallel implementation of dense Simplex Method. Our
implementation is implemented on a SMP cluster using C
programming language and the Message Passing Interface MPI.
Preliminary computational results on randomly generated dense
linear programs support our results.
Abstract: In the past 20 years the economy of the Czech
Republic has experienced substantial changes. In the 1990s the
development was affected by the transformation which sought to
establish the right conditions for privatization and creation of
elementary market relations. In the last decade the characteristic
elements such as private ownership and corresponding institutional
framework have been strengthened. This development was marked by
the accession of the Czech Republic to the EU. The Czech Republic
is striving to reduce the difference between its level of economic
development and the quality of institutional framework in
comparison with other developed countries. The process of finding
the adequate solutions has been hampered by the negative impact of
the world financial crisis on the Czech Republic and the standard of
living of its inhabitants. This contribution seeks to address the
question of whether and to which extent the economic development
of the transitive Czech economy is affected by the change in
behaviour of households and their tendency to consumption, i.e. in
the sense of reduction or increase in demand for goods and services.
It aims to verify whether the increasing trend of household
indebtedness and decreasing trend of saving pose a significant risk in
the Czech Republic. At a general level the analysis aims to contribute
to finding an answer to the question of whether the debt increase of
Czech households is connected to the risk of "eating through" the
borrowed money and whether Czech households risk falling into a
debt trap. In addition to household indebtedness risks in the Czech
Republic the analysis will focus on identification of specifics of the
transformation phase of the Czech economy in comparison with the
EU countries, or selected OECD countries.