Abstract: Soil erosion is the most serious problem faced at
global and local level. So planning of soil conservation measures has
become prominent agenda in the view of water basin managers. To
plan for the soil conservation measures, the information on soil
erosion is essential. Universal Soil Loss Equation (USLE), Revised
Universal Soil Loss Equation 1 (RUSLE1or RUSLE) and Modified
Universal Soil Loss Equation (MUSLE), RUSLE 1.06, RUSLE1.06c,
RUSLE2 are most widely used conventional erosion estimation
methods. The essential drawbacks of USLE, RUSLE1 equations are
that they are based on average annual values of its parameters and so
their applicability to small temporal scale is questionable. Also these
equations do not estimate runoff generated soil erosion. So
applicability of these equations to estimate runoff generated soil
erosion is questionable. Data used in formation of USLE, RUSLE1
equations was plot data so its applicability at greater spatial scale
needs some scale correction factors to be induced. On the other hand
MUSLE is unsuitable for predicting sediment yield of small and large
events. Although the new revised forms of USLE like RUSLE 1.06,
RUSLE1.06c and RUSLE2 were land use independent and they have
almost cleared all the drawbacks in earlier versions like USLE and
RUSLE1, they are based on the regional data of specific area and
their applicability to other areas having different climate, soil, land
use is questionable. These conventional equations are applicable for
sheet and rill erosion and unable to predict gully erosion and spatial
pattern of rills. So the research was focused on development of nonconventional
(other than conventional) methods of soil erosion
estimation. When these non-conventional methods are combined with
GIS and RS, gives spatial distribution of soil erosion. In the present
paper the review of literature on non- conventional methods of soil
erosion estimation supported by GIS and RS is presented.
Abstract: In this paper the authors propose and verify an approach to control heat flow in machine tool components. Thermal deformations are a main aspect that affects the accuracy of machining. Due to goals of energy efficiency, thermal basic loads should be reduced. This leads to inhomogeneous and time variant temperature profiles. To counteract these negative consequences, material with high melting enthalpy is used as a method for thermal stabilization. The increased thermal capacity slows down the transient thermal behavior. To account for the delayed thermal equilibrium, a control mechanism for thermal flow is introduced. By varying a gap in a heat flow path the thermal resistance of an assembly can be controlled. This mechanism is evaluated in two experimental setups. First to validate the ability to control the thermal resistance and second to prove the possibility of a self-sufficient option based on the selfsensing abilities of thermal shape memory alloys.
Abstract: This paper presents a CFD analysis of the flow field
around a thin flat plate of infinite span inclined at 90° to a fluid
stream of infinite extent. Numerical predictions have been compared
to experimental measurements, in order to assess the potential of the
finite volume code of determining the aerodynamic forces acting on a
bluff body invested by a fluid stream of infinite extent.
Several turbulence models and spatial node distributions have
been tested. Flow field characteristics in the neighborhood of the flat
plate have been investigated, allowing the development of a
preliminary procedure to be used as guidance in selecting the
appropriate grid configuration and the corresponding turbulence
model for the prediction of the flow field over a two-dimensional
vertical flat plate.
Abstract: Analysis for the generalized thermoelastic Lamb
waves, which propagates in anisotropic thin plates in generalized
thermoelasticity, is presented employing normal mode expansion
method. The displacement and temperature fields are expressed by a
summation of the symmetric and antisymmetric thermoelastic modes
in the surface thermal stresses and thermal gradient free orthotropic
plate, therefore the theory is particularly appropriate for waveform
analyses of Lamb waves in thin anisotropic plates. The transient
waveforms excited by the thermoelastic expansion are analyzed for
an orthotropic thin plate. The obtained results show that the theory
provides a quantitative analysis to characterize anisotropic
thermoelastic stiffness properties of plates by wave detection. Finally
numerical calculations have been presented for a NaF crystal, and the
dispersion curves for the lowest modes of the symmetric and
antisymmetric vibrations are represented graphically at different
values of thermal relaxation time. However, the methods can be used
for other materials as well
Abstract: It is estimated that the total cost of abnormal
conditions to US process industries is around $20 billion dollars in
annual losses. The hydrotreatment (HDT) of diesel fuel in petroleum
refineries is a conversion process that leads to high profitable
economical returns. However, this is a difficult process to control
because it is operated continuously, with high hydrogen pressures
and it is also subject to disturbances in feed properties and catalyst
performance. So, the automatic detection of fault and diagnosis plays
an important role in this context. In this work, a hybrid approach
based on neural networks together with a pos-processing
classification algorithm is used to detect faults in a simulated HDT
unit. Nine classes (8 faults and the normal operation) were correctly
classified using the proposed approach in a maximum time of 5
minutes, based on on-line data process measurements.
Abstract: In this paper, we propose a high capacity image hiding
technology based on pixel prediction and the difference of modified histogram. This approach is used the pixel prediction and the
difference of modified histogram to calculate the best embedding point.
This approach can improve the predictive accuracy and increase the pixel difference to advance the hiding capacity. We also use the
histogram modification to prevent the overflow and underflow. Experimental results demonstrate that our proposed method within the
same average hiding capacity can still keep high quality of image and low distortion
Abstract: Introduction applicability of high-speed cutting stock problem (CSP) is presented in this paper. Due to the orders continued coming in from various on-line ways for a professional cutting company, to stay competitive, such a business has to focus on sustained production at high levels. In others words, operators have to keep the machine running to stay ahead of the pack. Therefore, the continuous stock cutting problem with setup is proposed to minimize the cutting time and pattern changing time to meet the on-line given demand. In this paper, a novel method is proposed to solve the problem directly by using cutting patterns directly. A major advantage of the proposed method in series on-line production is that the system can adjust the cutting plan according to the floating orders. Examples with multiple items are demonstrated. The results show considerable efficiency and reliability in high-speed cutting of CSP.
Abstract: Optical burst switching(OBS) is considered as one of
preferable network technologies for the next generation Internet. The
Internet has two traffic classes, i.e. real-time bursts and reliable bursts.
It is an important subject for OBS to achieve cooperated operation of
real-time bursts and reliable bursts. In this paper, we proposes a new
effective traffic control method named Separate TB+LB (Token
Bucket + Leaky Bucket : TB+LB) method. The proposed method
presents a new Token Bucket scheme for real-time bursts called as
RBO-TB (Real-time Bursts Oriented Token Bucket). The method also
applies the LB method to reliable bursts for obtaining better
performance. This paper verifies the effectiveness of the Separate
TB+LB method through the performance evaluation.
Abstract: In the globalization context and competitiveness, the role of a university is further enhanced. University is no longer confined to traditional roles. Universities need to interact with others in order to be relevant and progressive. Symbiosis relationships between the university and industry are very significant because the relationship between those two can foster economic development of a nation. In a world of fast changing technology and competition, it is necessary for the university to collaborate with industry to combine efforts fostering the diffusion of knowledge, increasing research and development, patenting innovation and commercializing products. It has become increasingly accepted that the necessity of close university-industry interactions as a mean of national economic prosperity. Therefore, this paper is aim to examine the level of linkages in university-industry interactions to which promotes the regional economic growth and development. This paper will explore the formation of linkages between the Higher Education Institution (University Technology MARA) and industries located in the Klang Valley region of Malaysia. It will present the university-industry linkages with emphasis on the type of linkages existed, the benefits of having such linkages to promote regional economic development and finally the constraints that might impede the linkages and potentials to enhance the linkages towards economic growth and development.
Abstract: In this paper, a new reversible watermarking method is presented that reduces the size of a stereoscopic image sequence while keeping its content visible. The proposed technique embeds the residuals of the right frames to the corresponding frames of the left sequence, halving the total capacity. The residual frames may result in after a disparity compensated procedure between the two video streams or by a joint motion and disparity compensation. The residuals are usually lossy compressed before embedding because of the limited embedding capacity of the left frames. The watermarked frames are visible at a high quality and at any instant the stereoscopic video may be recovered by an inverse process. In fact, the left frames may be exactly recovered whereas the right ones are slightly distorted as the residuals are not embedded intact. The employed embedding method reorders the left frame into an array of consecutive pixel pairs and embeds a number of bits according to their intensity difference. In this way, it hides a number of bits in intensity smooth areas and most of the data in textured areas where resulting distortions are less visible. The experimental evaluation demonstrates that the proposed scheme is quite effective.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The efficient operation of any biological treatment
process requires pre-treatment of incompatible pollutants such as
acids, bases, oil, toxic substances, etc. which hamper the treatment
of other major components which are otherwise degradable. The
pre-treatment of alkaline waste-waters, generated from various
industries like textile, paper & pulp, potato-processing industries,
etc., having a pH of 10 or higher, is essential. The pre-treatment,
i.e., neutralization of such alkaline waste-waters can be achieved by
chemical as well as biological means. However, the biological pretreatment
offers better package over the chemical means by being
safe and economical. The biological pre-treatment can be
accomplished by using a blend of microorganisms able to withstand
such harsh alkaline conditions. In the present study, for the proper
pre-treatment of alkaline waste-waters, a package of alkalophilic
bacteria is formulated to neutralise the alkaline pH of the industrial
waste-waters. The developed microbial package is cost-effective as
well as environmental friendly.
Abstract: The paper shows how the perceptions of five organizational virtuousness dimensions (optimism, trust, compassion, integrity, and forgiveness) explain organizational citizenship behaviors (altruism, sportsmanship, courtesy, conscientiousness, and civic virtue). A sample comprising 216 individuals from 14 industrial organizations was collected. Individuals reported their perceptions of organizational virtuousness, their organizational citizenship behaviors (OCB) being reported by their supervisors. The main findings are the following: (a) the perceptions of trust predict altruism; (b) the perceptions of integrity predict civic virtue.
Abstract: Existing underground pipe jacking methods use a
reinforcing rod in a steel tube to obtain structural stiffness. However,
some problems such as inconvenience of works and expensive
materials resulted from limited working space and reinforcing works
are existed. To resolve these problems, a new pipe jacking method,
namely PST (Prestressed Segment Tunnel) method, was developed
which used joint to connect the steel segment and form erection
structure. For evaluating the flexural capacity of the PST method
structure, a experimental test was conducted. The parameters
considered in the test were span-to-depth ratio of segment, diameter of
steel tube at the corner, prestressing force, and welding of joint. The
flexural behaviours with the effect of load capacity in serviceability
state according to different parameters were examined.. The frame
with long segments could increase flexural stiffness and the specimen
with large diameter of concave corner showed excellent resistance
ability to the negative moment. In addition, welding of joints increased
the flexural capacity.
Abstract: The reliability of distributed systems and computer
networks have been modeled by a probabilistic network or a graph G.
Computing the residual connectedness reliability (RCR), denoted by
R(G), under the node fault model is very useful, but is an NP-hard
problem. Since it may need exponential time of the network size to
compute the exact value of R(G), it is important to calculate its tight
approximate value, especially its lower bound, at a moderate
calculation time. In this paper, we propose an efficient algorithm for
reliability lower bound of distributed systems with unreliable nodes.
We also applied our algorithm to several typical classes of networks
to evaluate the lower bounds and show the effectiveness of our
algorithm.
Abstract: Erwinia carotovora var. carotovora is the main cause of soft rot in potatoes. Hyphaene thebaica was studied for biocontrol of E. carotovora which inhibited growth of E. carotovora on solid medium, a comparative study of classical and ultrasound-assisted extractions of Hyphaene thebaica fruit. The use of ultrasound decreased significant the total time of treatment and increase the total amount of crude extract. The crude extract was subjected to determine the in vitro, by a bioassay technique revealed that the treatment of paper disks with ultrasound extraction of Hyphaene thebaica reduced the growth of pathogen and produced inhibition zones up to 38mm in diameter. The antioxidant activity of ultrasound-ethanolic extract of Doum fruits (Hyphaene thebaica) was determined. Data obtained showed that the extract contains the secondary metabolites such as Tannins, Saponin, Flavonoids, Phenols, Steroids, Terpenoids, Glycosides and Alkaloids.
Abstract: We describe a work with an evolutionary computing
algorithm for non photo–realistic rendering of a target image. The
renderings are produced by genetic programming. We have used two
different types of strokes: “empty triangle" and “filled triangle" in
color level. We compare both empty and filled triangular strokes to
find which one generates more aesthetic pleasing images. We found
the filled triangular strokes have better fitness and generate more
aesthetic images than empty triangular strokes.
Abstract: In this paper, we study the existence of solution of
the four-point boundary value problem for second-order differential
equations with impulses by using leray-Schauder theory:
Abstract: The progress of concentrations of particular heavy metals was assessed in chosen localities in region Moravia, the Czech Republic, from 2007 to 2009. Particular metals were observed in localities with various types and characterization of zone. Pb, Ni, As and Cd were emphasized as a result of their toxicity and potential adverse health effect to the exposed population. The progress of metal concentrations and their health effects in the most polluted localities were examined. According to the results, the air pollution limit values were not exceeded. Based on the health risk assessment, the probability of developing tumorous diseases is acceptable, except for the increased probability of cancer risk from long-term exposure to As.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.