Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: A novel path planning approach is presented to solve
optimal path in stochastic, time-varying networks under priori traffic
information. Most existing studies make use of dynamic programming
to find optimal path. However, those methods are proved to
be unable to obtain global optimal value, moreover, how to design
efficient algorithms is also another challenge.
This paper employs a decision theoretic framework for defining
optimal path: for a given source S and destination D in urban transit
network, we seek an S - D path of lowest expected travel time
where its link travel times are discrete random variables. To solve
deficiency caused by the methods of dynamic programming, such as
curse of dimensionality and violation of optimal principle, an integer
programming model is built to realize assignment of discrete travel
time variables to arcs. Simultaneously, pruning techniques are also
applied to reduce computation complexity in the algorithm. The final
experiments show the feasibility of the novel approach.
Abstract: In modern distributed software systems, the issue of communication among composing parts represents a critical point, but the idea of extending conventional programming languages with general purpose communication constructs seems difficult to realize. As a consequence, there is a (growing) gap between the abstraction level required by distributed applications and the concepts provided by platforms that enable communication. This work intends to discuss how the Model Driven Software Development approach can be considered as a mature technology to generate in automatic way the schematic part of applications related to communication, by providing at the same time high level specialized languages useful in all the phases of software production. To achieve the goal, a stack of languages (meta-meta¬models) has been introduced in order to describe – at different levels of abstraction – the collaborative behavior of generic entities in terms of communication actions related to a taxonomy of messages. Finally, the generation of platforms for communication is viewed as a form of specification of language semantics, that provides executable models of applications together with model-checking supports and effective runtime environments.
Abstract: In the present work flow past circular cylinder and
cylinder with rectangular and triangular wake splitter is studied to
improve aerodynamic parameters. The Comparison of drag
coefficient is tabulated for bare cylinder, cylinder with rectangular
and triangular wake splitters. Flow past circular cylinder and cylinder
with triangular and rectangular wake splitter is performed at
Reynoldsnumber 5, 20, 40, 50,80, 100.An incompressible PISO finite
volume code employing a non-staggered grid arrangement is used, a
second order upwind scheme is used for convective terms. The time
discretization is implicit and a Second order Crank-Nicholson scheme
is employed. Length of wake splitter in both configurations is taken
to be equal to diameter of cylinder. Wake length is found to be less
with rectangular wake splitter when compared to bare cylinder and
cylinder with triangular wake splitter. Coefficient of drag is found to
be less for triangular wake splitter when compared to bare cylinder &
cylinder with rectangular wake splitter.
Abstract: Electrocardiogram (ECG) is considered to be the
backbone of cardiology. ECG is composed of P, QRS & T waves and
information related to cardiac diseases can be extracted from the
intervals and amplitudes of these waves. The first step in extracting
ECG features starts from the accurate detection of R peaks in the
QRS complex. We have developed a robust R wave detector using
wavelets. The wavelets used for detection are Daubechies and
Symmetric. The method does not require any preprocessing therefore,
only needs the ECG correct recordings while implementing the
detection. The database has been collected from MIT-BIH arrhythmia
database and the signals from Lead-II have been analyzed. MatLab
7.0 has been used to develop the algorithm. The ECG signal under
test has been decomposed to the required level using the selected
wavelet and the selection of detail coefficient d4 has been done based
on energy, frequency and cross-correlation analysis of decomposition
structure of ECG signal. The robustness of the method is apparent
from the obtained results.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: During this day a considerable amount of Leachate is produced with high amounts of organic material and nutrients needed plants. This study has done in order to scrutinize the effect of Leachate compost on the pH, EC and organic matter percentage in the form of statistical Factorial plan through randomizing block design with three main and two minor treatments and also three replications during three six month periods. Major treatments include N: Irrigation with the region-s well water as a control, I: Frequent irrigation with well water and Leachate, C: Mixing Leachate and water well (25 percent leachate + 75 percent ordinary well water) and secondary treatments, include DI: surface drip irrigation and SDI: sub surface drip irrigation. Results of this study indicated significant differences between treatments and also there were mixing up with the control treatment in the reduction of pH, increasing soluble salts and also increasing the organic matter percentage. This increase is proportional to the amount of added Leachate and in the treatment also proportional to higher mixture of frequent treatment. Therefore, since creating an acidic pH increases the ability to absorb some nutrient elements such as phosphorus, iron, zinc, copper and manganese are increased and the other hand, organic materials also improve many physical and chemical properties of soil are used in Leachate trash Consider health issues as refined in the green belts around cities as a liquid fertilizer recommended.
Abstract: In the context of global climate change, flooding and sea level rise is increasingly threatening coastal urban areas, in which large population is continuously concentrated. Dutch experiences in urban water system management provide high reference value for sustainable coastal urban development projects. Preliminary studies shows the urban water system in Almere, a typical Dutch polder city, have three kinds of operational modes, achieving functions as: (1) coastline control – strong multiple damming system prevents from storm surges and maintains sufficient capacity upon risks; (2) high flexibility – large area and widely scattered open water system greatly reduce local runoff and water level fluctuation; (3) internal water maintenance – weir and sluice system maintains relatively stable water level, providing excellent boating and landscaping service, coupling with water circulating model maintaining better water quality. Almere has provided plenty of hints and experiences for ongoing development of coastal cities in emerging economies.
Abstract: the work contains the results of complex investigation
related to the evaluation of condition of working blades of gas turbine
engines during fatigue tests by applying the acoustic emission
method. It demonstrates the possibility of estimating the fatigue
damage of blades in the process of factory tests. The acoustic
emission criteria for detecting and testing the kinetics of fatigue crack
distribution were detected. It also shows the high effectiveness of the
method for non-destructive testing of condition of solid and cooled
working blades for high-temperature gas turbine engines.
Abstract: It is well known that during the developments in the
economic sector and through the financial crises occur everywhere in
the whole world, volatility measurement is the most important
concept in financial time series. Therefore in this paper we discuss
the volatility for Amman stocks market (Jordan) for certain period of
time. Since wavelet transform is one of the most famous filtering
methods and grows up very quickly in the last decade, we compare
this method with the traditional technique, Fast Fourier transform to
decide the best method for analyzing the volatility. The comparison
will be done on some of the statistical properties by using Matlab
program.
Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.
Abstract: The paper presents the modeling of nonlinear
longitudinal aerodynamics using flight data of Hansa-3 aircraft at
high angles of attack near stall. The Kirchhoff-s quasi-steady stall
model has been used to incorporate nonlinear aerodynamic effects in
the aerodynamic model used to estimate the parameters, thereby,
making the aerodynamic model nonlinear. The Maximum Likelihood
method has been applied to the flight data (at high angles of attack)
for the estimation of parameters (aerodynamic and stall
characteristics) using the nonlinear aerodynamic model. To improve
the accuracy level of the estimates, an approach of fixing the strong
parameters has also been presented.
Abstract: The purpose of this research was to investigate Thai Muslims’ way of life through the way their clothes. The data of this qualitative research were collected from related documents and research reports, ancient cloths and clothing, and in-depth interviews with clothes owners and weavers.
The research found that in the 18th century Thai Muslims in the three southern border provinces used many types of clothing in their life. At home women wore plain clothes. They used checked cloths to cover the upper part of their body from the breasts down to the waist. When going out, they used Lima cloth and So Kae with a piece of Pla-nging cloth as a head scarf. For men, they wore a checked sarong as a lower garment, and wore no upper garment. However, when going out, they wore Puyo Potong. In addition, Thai Muslims used cloths in various religious rites, namely, the rite of placing a baby in a cradle, the Masoyawi rite, the Nikah rite, and the burial rite. These types of cloths were related to the way of life of Thai Muslims from birth to death. They reflected the race, gender, age, social status, values, and beliefs in traditions that have been inherited.
Practical Implication: Woven in these cloths are the lost local wisdom, and therefore, aesthetics on the cloths are like mirrors reflecting the background of people in this region that is fading away. These cloths are pages of a local history book that is of importance and value worth for preservation and publicity so that they are treasured. Government organizations can expand and materialize the knowledge received from the study in accordance with government policy in supporting the One Tambon, One Product project.
Abstract: The emergence of mobile application services and App
Store has led to the explosive growth of user innovation, which users
voluntarily contribute to. User innovation communities where end
users freely reveal innovative ideas and needs with other community
members are becoming increasingly influential in this area. However,
user-s ideas in user innovation community are not enough to be new
service opportunity, because some of them can already developed as
existing services in App Store. Moreover, the existing services similar
to new service opportunity can be significant references to apply
analogy to develop service concept. In response, this research
proposes Case-Based Reasoning approach to matching the user needs
and existing services, identifying unmet opportunistic user needs, and
retrieving similar services with opportunity. Due to its intuitive and
transparent algorithm, users related to App Store innovation
communities can easily employ Case-Based Reasoning based
approach to their innovation.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: The position and momentum space information entropies
of hydrogen atom are exactly evaluated. Using isospectral
Hamiltonian approach, a family of isospectral potentials is constructed having same energy eigenvalues as that of the original potential. The information entropy content is obtained in position
space as well as in momentum space. It is shown that the information
entropy content in each level can be re-arranged as a function of deformation parameter.
Abstract: Intellectual capital reporting becomes critical at
universities, mainly due to the fact that knowledge is the main output
as well as input in these institutions. In addition, universities have
continuous external demands for greater information and
transparency about the use of public funds, and are increasingly
provided with greater autonomy regarding their organization,
management, and budget allocation. This situation requires new
management and reporting systems. The purpose of the present study
is to provide a model for intellectual capital report in Spanish
universities. To this end, a questionnaire was sent to every member of
the Social Councils of Spanish public universities in order to identify
which intangible elements university stakeholders demand most. Our
proposal for an intellectual capital report aims to act as a guide to
help the Spanish universities on the road to the presentation of
information on intellectual capital which can assist stakeholders to
make the right decisions.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: This paper presents a new method of analog fault diagnosis based on back-propagation neural networks (BPNNs) using wavelet decomposition and fractal dimension as preprocessors. The proposed method has the capability to detect and identify faulty components in an analog electronic circuit with tolerance by analyzing its impulse response. Using wavelet decomposition to preprocess the impulse response drastically de-noises the inputs to the neural network. The second preprocessing by fractal dimension can extract unique features, which are the fed to a neural network as inputs for further classification. A comparison of our work with [1] and [6], which also employs back-propagation (BP) neural networks, reveals that our system requires a much smaller network and performs significantly better in fault diagnosis of analog circuits due to our proposed preprocessing techniques.
Abstract: Median filter is widely used to remove impulse noise
without blurring sharp edges. However, when noise level increased,
or with thin edges, median filter may work poorly. This paper
proposes a new filter, which will detect edges along four possible
directions, and then replace noise corrupted pixel with estimated
noise-free edge median value. Simulations show that the proposed
multi-stage directional median filter can provide excellent
performance of suppressing impulse noise in all situations.