Abstract: Only recently have water ethics received focused interest in the international water community. Because water is metabolically basic to life, an ethical dimension persists in every decision related to water. Water ethics at once express human society-s approach to water and act as guidelines for behaviour. Ideas around water are often implicit and embedded as assumptions. They can be entrenched in behaviour and difficult to contest because they are difficult to “see". By explicitly revealing the ethical ideas underlying water-related decisions, human society-s relationship with water, and with natural systems of which water is part, can be contested and shifted or be accepted with conscious intention by human society. In recent decades, improved understanding of water-s importance for ecosystem functioning and ecological services for human survival is moving us beyond this growth-driven, supplyfocused management paradigm. Environmental ethics challenge this paradigm by extending the ethical sphere to the environment and thus water or water Resources management per se. An ethical approach is a legitimate, important, and often ignored approach to effect change in environmental decision making. This qualitative research explores principles of water ethics and examines the underlying ethical precepts of selected water policy examples. The constructed water ethic principles act as a set of criteria against which a policy comparison can be established. This study shows that water Resources management is a progressive issue by embracing full public participation and a new planning model, and knowledgegeneration initiatives.
Abstract: Using efficient classification methods is necessary for automatic fingerprint recognition system. This paper introduces a new structural approach to fingerprint classification by using the directional image of fingerprints to increase the number of subclasses. In this method, the directional image of fingerprints is segmented into regions consisting of pixels with the same direction. Afterwards the relational graph to the segmented image is constructed and according to it, the super graph including prominent information of this graph is formed. Ultimately we apply a matching technique to compare obtained graph with the model graphs in order to classify fingerprints by using cost function. Increasing the number of subclasses with acceptable accuracy in classification and faster processing in fingerprints recognition, makes this system superior.
Abstract: A road pricing game is a game where various stakeholders and/or regions with different (and usually conflicting) objectives compete for toll setting in a given transportation network to satisfy their individual objectives. We investigate some classical game theoretical solution concepts for the road pricing game. We establish results for the road pricing game so that stakeholders and/or regions playing such a game will beforehand know what is obtainable. This will save time and argument, and above all, get rid of the feelings of unfairness among the competing actors and road users. Among the classical solution concepts we investigate is Nash equilibrium. In particular, we show that no pure Nash equilibrium exists among the actors, and further illustrate that even “mixed Nash equilibrium" may not be achievable in the road pricing game. The paper also demonstrates the type of coalitions that are not only reachable, but also stable and profitable for the actors involved.
Abstract: The mathematical modeling of storm surge in sea and
coastal regions such as the South China Sea (SCS) and the Gulf of
Thailand (GoT) are important to study the typhoon characteristics.
The storm surge causes an inundation at a lateral boundary exhibiting
in the coastal zones particularly in the GoT and some part of the SCS.
The model simulations in the three dimensional primitive equations
with a high resolution model are important to protect local properties
and human life from the typhoon surges. In the present study, the
mathematical modeling is used to simulate the typhoon–induced
surges in three case studies of Typhoon Linda 1997. The results
of model simulations at the tide gauge stations can describe the
characteristics of storm surges at the coastal zones.
Abstract: In this paper, a novel system
recognition of human faces without using face
different color photographs is proposed. It mainly in
face detection, normalization and recognition. Foot
method of combination of Haar-like face determined
segmentation and region-based histogram stretchi
(RHST) is proposed to achieve more accurate perf
using Haar. Apart from an effective angle norm
side-face (pose) normalization, which is almost a might be important and beneficial for the prepr
introduced. Then histogram-based and photom
normalization methods are investigated and ada
retinex (ASR) is selected for its satisfactory illumin
Finally, weighted multi-block local binary pattern
with 3 distance measures is applied for pair-mat
Experimental results show its advantageous perfo
with PCA and multi-block LBP, based on a principle.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.
Abstract: In recent years, there has been an increasing interest in using daylight to save energy in buildings. In tropical regions, daylighting is always an energy saver. On the other hand, daylight provides visual comfort. According to standards, it shows that many criteria should be taken into consideration in order to have daylight utilization and visual comfort. The current standard in Malaysia, MS 1525 does not provide sufficient guideline. Hence, more research is needed on daylight performance. If architects do not consider daylight design, it not only causes inconvenience in working spaces but also causes more energy consumption as well as environmental pollution. This research had surveyed daylight performance in 5 selected office buildings from different area of Malaysian through experimental method. Several parameters of daylight quality such as daylight factor, surface luminance and surface luminance ratio were measured in different rooms in each building. The result of this research demonstrated that most of the buildings were not designed for daylight utilization. Therefore, it is very important that architects follow the daylight design recommendation to reduce consumption of electric power for artificial lighting while the sufficient quality of daylight is available.
Abstract: We present a Large-Eddy simulation of a vortex cell
with circular shaped. The results show that the flow field can be sub
divided into four important zones, the shear layer above the cavity,
the stagnation zone, the vortex core in the cavity and the boundary
layer along the wall of the cavity. It is shown that the vortex core
consits of solid body rotation without much turbulence activity. The
vortex is mainly driven by high energy packets that are driven into the
cavity from the stagnation point region and by entrainment of fluid
from the cavity into the shear layer. The physics in the boundary
layer along the cavity-s wall seems to be far from that of a canonical
boundary layer which might be a crucial point for modelling this
flow.
Abstract: The paper presents the case study of hazard
identification and sensitivity of potential resource of emergency
water supply as part of the application of methodology classifying
the resources of drinking water for emergency supply of population.
The case study has been carried out on a selected resource of
emergency water supply in one region of the Czech Republic. The
hazard identification and sensitivity of potential resource of
emergency water supply is based on a unique procedure and
developed general registers of selected types of hazards and
sensitivities. The registers have been developed with the help of the
“Fault Tree Analysis” method in combination with the “What if
method”. The identified hazards for the assessed resource include
hailstorms and torrential rains, drought, soil erosion, accidents of
farm machinery, and agricultural production. The developed registers
of hazards and vulnerabilities and a semi-quantitative assessment of
hazards for individual parts of hydrological structure and
technological elements of presented drilled wells are the basis for a
semi-quantitative risk assessment of potential resource of emergency
supply of population and the subsequent classification of such
resource within the system of crisis planning.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: From the beginning of creation, human being has ever
fought against the ecosystem by changes has made in environment.
The most environmental changes on the nature have been done after
starting the concentrated life in the same region. Dams are one of the
most important buildings in water resources and transferring. These
buildings have been made from old times without access to
hydrological, hydraulically, hydro mechanical information. Dams
have positive and negative effects on environment. Constructing a
dam relatively causes equal ecological consequences. According to
different criteria, environmental effects of dams can lead short term
and long term damages. These effects may influence on the situation
and treatment of meteorology, biology, culture, ancient works, etc
and severely causes to change and complicate it. So considering
importance of positive effects of dam construction, it is necessary to
minimize negative environmental effects of dams to achieve a stable
development. In this article the considered effects and their solutions
in influencing on assessment of destructive environmental effects of
dams construction have been surveyed and presented.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: Clustering algorithms are attractive for the task of class identification in spatial databases. However, the application to large spatial databases rises the following requirements for clustering algorithms: minimal requirements of domain knowledge to determine the input parameters, discovery of clusters with arbitrary shape and good efficiency on large databases. The well-known clustering algorithms offer no solution to the combination of these requirements. In this paper, a density based clustering algorithm (DCBRD) is presented, relying on a knowledge acquired from the data by dividing the data space into overlapped regions. The proposed algorithm discovers arbitrary shaped clusters, requires no input parameters and uses the same definitions of DBSCAN algorithm. We performed an experimental evaluation of the effectiveness and efficiency of it, and compared this results with that of DBSCAN. The results of our experiments demonstrate that the proposed algorithm is significantly efficient in discovering clusters of arbitrary shape and size.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: Loop detectors report traffic characteristics in real
time. They are at the core of traffic control process. Intuitively,
one would expect that as density of detection increases, so would
the quality of estimates derived from detector data. However, as
detector deployment increases, the associated operating and
maintenance cost increases. Thus, traffic agencies often need to
decide where to add new detectors and which detectors should
continue receiving maintenance, given their resource constraints.
This paper evaluates the effect of detector spacing on freeway
travel time estimation. A freeway section (Interstate-15) in Salt
Lake City metropolitan region is examined. The research reveals
that travel time accuracy does not necessarily deteriorate with
increased detector spacing. Rather, the actual location of detectors
has far greater influence on the quality of travel time estimates.
The study presents an innovative computational approach that
delivers optimal detector locations through a process that relies on
Genetic Algorithm formulation.
Abstract: Accurate and comprehensive thermodynamic properties of pure and mixture of refrigerants are in demand by both producers and users of these materials. Information about thermodynamic properties is important initially to qualify potential candidates for working fluids in refrigeration machinery. From practical point of view, Refrigerants and refrigerant mixtures are widely used as working fluids in many industrial applications, such as refrigerators, heat pumps, and power plants The present work is devoted to evaluating seven cubic equations of state (EOS) in predicting gas and liquid phase volumetric properties of nine ozone-safe refrigerants both in super and sub-critical regions. The evaluations, in sub-critical region, show that TWU and PR EOS are capable of predicting PVT properties of refrigerants R32 within 2%, R22, R134a, R152a and R143a within 1% and R123, R124, R125, TWU and PR EOS's, from literature data are 0.5% for R22, R32, R152a, R143a, and R125, 1% for R123, R134a, and R141b, and 2% for R124. Moreover, SRK EOS predicts PVT properties of R22, R125, and R123 to within aforementioned errors. The remaining EOS's predicts volumetric properties of this class of fluids with higher errors than those above mentioned which are at most 8%.In general, the results are in favor of the preference of TWU and PR EOS over other remaining EOS's in predicting densities of all mentioned refrigerants in both super and sub critical regions. Typically, this refrigerant is known to offer advantages such as ozone depleting potential equal to zero, Global warming potential equal to 140, and no toxic.
Abstract: In this study, Friction Stir Processing (FSP) a recent grain refinement technique was employed to disperse micron-sized (2 *m) SiCp particles into aluminum alloy AA6063. The feasibility to fabricate bulk composites through FSP was analyzed and experiments were conducted at different traverse speeds and wider volumes of the specimens. Micro structural observation were carried out by employing optical microscopy test of the cross sections in both parallel and perpendicular to the tool traverse direction. Mechanical property including micro hardness was evaluated in detail at various regions on the specimen. The composites had an excellent bonding with aluminum alloy substrate and a significant increase of 30% in the micro hardness value of metal matrix composite (MMC) as to that of the base metal has observed. The observations clearly indicate that SiC particles were uniformly distributed within the aluminum matrix.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: In the paper a detailed analysis of the dynamic
response of a cooling tower shell to mining tremors originated from
two main regions of mining activity in Poland (Upper Silesian Coal
Basin and Legnica-Glogow Copper District) was presented. The
representative time histories registered in the both regions were used
as ground motion data in calculations of the dynamic response of the
structure. It was proved that the dynamic response of the shell is
strongly dependent not only on the level of vibration amplitudes but
on the dominant frequency range of the mining shock typical for the
mining region as well. Also a vertical component of vibrations
occurred to have considerable influence on the total dynamic
response of the shell. Finally, it turned out that non-uniformity of
kinematic excitation resulting from spatial variety of ground motion
plays a significant role in dynamic analysis of large-dimensional
shells under mining shocks.