Abstract: This paper is concerned with propagation of thermoelastic longitudinal vibrations of an infinite circular cylinder, in the context of the linear theory of generalized thermoelasticity with two relaxation time parameters (Green and Lindsay theory). Three displacement potential functions are introduced to uncouple the equations of motion. The frequency equation, by using the traction free boundary conditions, is given in the form of a determinant involving Bessel functions. The roots of the frequency equation give the value of the characteristic circular frequency as function of the wave number. These roots, which correspond to various modes, are numerically computed and presented graphically for different values of the thermal relaxation times. It is found that the influences of the thermal relaxation times on the amplitudes of the elastic and thermal waves are remarkable. Also, it is shown in this study that the propagation of thermoelastic longitudinal vibrations based on the generalized thermoelasticity can differ significantly compared with the results under the classical formulation. A comparison of the results for the case with no thermal effects shows well agreement with some of the corresponding earlier results.
Abstract: This paper presents a Reliability-Based Topology
Optimization (RBTO) based on Evolutionary Structural Optimization
(ESO). An actual design involves uncertain conditions such as
material property, operational load and dimensional variation.
Deterministic Topology Optimization (DTO) is obtained without
considering of the uncertainties related to the uncertainty parameters.
However, RBTO involves evaluation of probabilistic constraints,
which can be done in two different ways, the reliability index
approach (RIA) and the performance measure approach (PMA). Limit
state function is approximated using Monte Carlo Simulation and
Central Composite Design for reliability analysis. ESO, one of the
topology optimization techniques, is adopted for topology
optimization. Numerical examples are presented to compare the DTO
with RBTO.
Abstract: In this paper, an attempt is made to compute the total
optimal cost of interdependent queuing system with controllable
arrival rates as an important performance measure of the system. An
example of application has also been presented to exhibit the use of
the model. Finally, numerical demonstration based on a computing
algorithm and variational effects of the model with the help of the
graph have also been presented.
Abstract: The classification of the protein structure is commonly
not performed for the whole protein but for structural domains, i.e.,
compact functional units preserved during evolution. Hence, a first
step to a protein structure classification is the separation of the
protein into its domains. We approach the problem of protein domain
identification by proposing a novel graph theoretical algorithm. We
represent the protein structure as an undirected, unweighted and
unlabeled graph which nodes correspond the secondary structure
elements of the protein. This graph is call the protein graph. The
domains are then identified as partitions of the graph corresponding
to vertices sets obtained by the maximization of an objective function,
which mutually maximizes the cycle distributions found in the
partitions of the graph. Our algorithm does not utilize any other kind
of information besides the cycle-distribution to find the partitions. If
a partition is found, the algorithm is iteratively applied to each of
the resulting subgraphs. As stop criterion, we calculate numerically
a significance level which indicates the stability of the predicted
partition against a random rewiring of the protein graph. Hence,
our algorithm terminates automatically its iterative application. We
present results for one and two domain proteins and compare our
results with the manually assigned domains by the SCOP database
and differences are discussed.
Abstract: This paper proposes a delay-dependent leader-following consensus condition of multi-agent systems with both communication delay and probabilistic self-delay. The proposed methods employ a suitable piecewise Lyapunov-Krasovskii functional and the average dwell time approach. New consensus criterion for the systems are established in terms of linear matrix inequalities (LMIs) which can be easily solved by various effective optimization algorithms. Numerical example showed that the proposed method is effective.
Abstract: The intelligent fuzzy input estimator is used to estimate
the input force of the rigid bar structural system in this study. The
fuzzy Kalman filter without the input term and the fuzzy weighting
recursive least square estimator are two main portions of this method.
The practicability and accuracy of the proposed method were verified
with numerical simulations from which the input forces of a rigid bar
structural system were estimated from the output responses. In order to
examine the accuracy of the proposed method, a rigid bar structural
system is subjected to periodic sinusoidal dynamic loading. The
excellent performance of this estimator is demonstrated by comparing
it with the use of difference weighting function and improper the
initial process noise covariance. The estimated results have a good
agreement with the true values in all cases tested.
Abstract: A reduced order modeling approach for natural
gas transient flow in pipelines is presented. The Euler
equations are considered as the governing equations and
solved numerically using the implicit Steger-Warming flux
vector splitting method. Next, the linearized form of the
equations is derived and the corresponding eigensystem is
obtained. Then, a few dominant flow eigenmodes are used to
construct an efficient reduced-order model. A well-known test
case is presented to demonstrate the accuracy and the
computational efficiency of the proposed method. The results
obtained are in good agreement with those of the direct
numerical method and field data. Moreover, it is shown that
the present reduced-order model is more efficient than the
conventional numerical techniques for transient flow analysis
of natural gas in pipelines.
Abstract: Following the laser ablation studies leading to a
theory of nuclei confinement by a Debye layer mechanism, we
present here numerical evaluations for the known stable nuclei where
the Coulomb repulsion is included as a rather minor component
especially for lager nuclei. In this research paper the required
physical conditions for the formation and stability of nuclei
particularly endothermic nuclei with mass number greater than to
which is an open astrophysical question have been investigated.
Using the Debye layer mechanism, nuclear surface energy, Fermi
energy and coulomb repulsion energy it is possible to find conditions
under which the process of nucleation is permitted in early universe.
Our numerical calculations indicate that about 200 second after the
big bang at temperature of about 100 KeV and subrelativistic region
with nucleon density nearly equal to normal nuclear density namely,
10cm all endothermic and exothermic nuclei have been
formed.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: In this paper, the 1-D conduction-radiation problem is solved by the lattice Boltzmann method. The effects of various parameters such as the scattering albedo, the conduction–radiation parameter and the wall emissivity are studied. In order to check on the accuracy of the numerical technique employed for the solution of the considered problem, the present numerical code was validated with the published study. The found results are in good agreement with those published
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.
Abstract: Real-time measurement of applied forces, like tension, compression, torsion, and bending moment, identifies the transferred energies being applied to the bottomhole assembly (BHA). These forces are highly detrimental to measurement/logging-while-drilling tools and downhole equipment. Real-time measurement of the dynamic downhole behavior, including weight, torque, bending on bit, and vibration, establishes a real-time feedback loop between the downhole drilling system and drilling team at the surface. This paper describes the numerical analysis of the strain data acquired by the measurement tool at different locations on the strain pockets. The strain values obtained by FEA for various loading conditions (tension, compression, torque, and bending moment) are compared against experimental results obtained from an identical experimental setup. Numerical analyses results agree with experimental data within 8% and, therefore, substantiate and validate the FEA model. This FEA model can be used to analyze the combined loading conditions that reflect the actual drilling environment.
Abstract: Recently, Uhlig [Numer. Algorithms, 52(3):335-353, 2009] proposed open questions about the ratios between the spectral norm, the numerical radius and the spectral radius of a square matrix. In this note, we provide some observations to answer these questions.
Abstract: A highly optimized implementation of binary mixture
diffusion with no initial bulk velocity on graphics processors is
presented. The lattice Boltzmann model is employed for simulating
the binary diffusion of oxygen and nitrogen into each other with
different initial concentration distributions. Simulations have been
performed using the latest proposed lattice Boltzmann model that
satisfies both the indifferentiability principle and the H-theorem for
multi-component gas mixtures. Contemporary numerical
optimization techniques such as memory alignment and increasing
the multiprocessor occupancy are exploited along with some novel
optimization strategies to enhance the computational performance on
graphics processors using the C for CUDA programming language.
Speedup of more than two orders of magnitude over single-core
processors is achieved on a variety of Graphical Processing Unit
(GPU) devices ranging from conventional graphics cards to
advanced, high-end GPUs, while the numerical results are in
excellent agreement with the available analytical and numerical data
in the literature.
Abstract: In this study, a semi-cylinder obstacle placed in a
channel is handled to determine the effect of flow and heat transfer
around the obstacle. Both faces of the semi-cylinder are used in the
numerical analysis. First, the front face of the semi-cylinder is stated
perpendicular to flow, than the rear face is placed. The study is
carried out numerically, by using commercial software ANSYS 11.0.
The well-known κ-ε model is applied as the turbulence model.
Reynolds number is in the range of 104 to 105 and air is assumed as
the flowing fluid. The results showed that, heat transfer increased
approximately 15 % in the front faze case, while it enhanced up to 28
% in the rear face case.
Abstract: The present study was provided to examine the
vortical structures generated by two inclined impinging jets with
experimental and numerical investigations. The jets are issuing with a
pitch angle α=40° into a confined quiescent fluid. The experimental
investigation on flow patterns was visualized by using olive particles
injected into the jets illuminated by Nd:Yag laser light to reveal the
finer details of the confined jets interaction. It was observed that two
counter-rotating vortex pairs (CVPs) were generated in the near
region. A numerical investigation was also performed. First, the
numerical results were validates against the experimental results and
then the numerical model was used to study the effect of section ratio
on the evolution of the CVPs. Our results show promising agreement
with experimental data, and indicate that our model has the potential
to produce useful and accurate data regarding the evolution of CVPs.